Info button Acura RDX 2007 Workshop Manual

µ
µ
µ
µ Select
this button to begin the process
required to connect to Acura. This is
used to access the most recent
diagnostic information when a
problem occurs. Select
ON to have
the system automatically read each
message to you. Select OFF to
manually select the Voice button
when you want a message read to
you.
To
access the following functions,
press the SETUP button, push the
interface dial to the right to select
MORE, then rotate the interface dial
to select AcuraLink/Messages.
Select this
button to delete all stored messages
within a category, except for
diagnostic info and recall campaign
messages. These messages can only
be deleted by a certified technician
after the recall is done or the
problem is corrected, or through a
broadcast message from Acura.
Select ON if you want to be notified
of new messages (envelope icon
appears on the naviga tion screen).
Select OFF if you do not want to be
noti fied of new messages (envelope
icon does not appear on the
naviga tion screen). For
the Phone Data
Connection button to be active, you
need a Bluetooth compatible and
enabled cellphone paired to the
HandsFreeLink (HFL), and a
compatible data service (see on page ).262
AcuraLink
AcuraL ink/Message Screen
Phone-Data Connection Auto Reading
Delete Messages
New Message Notif ication
Pairing
Your Phone
248
NOTE:
——
y
y
() yy

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure. Press the HomeLink button again
f or about 1 second. It should
operate the garage door.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes. Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
6.
2. 4.
5.
1. 3.
T raining With a Rolling Code
System
HomeL ink Universal Transceiver
Features
255
TRAINING BUTTON
——
y


y
() yy

Youshoulderaseallthreecodes
before selling the vehicl e.
Toerasethecodesstoredinallthree
buttons,
press and hold the two
outside buttons until the red
indicator begins to flash, then
release the buttons.
If you want to retrain a programmed
button for a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure: If
a standard transmitter was
programmed, the indicator will
stay on for about 25 seconds.
HomeLink
is a registered
trad emark of Johnson Controls, Inc.
If
you have problems with training
the HomeLink Universal Transceiver,
or would like information on home
products that can be operated by
HomeLink, call (800) 355-3515. On
the Internet, go to
www.homelink.com. Once
the HomeLink indicator
begins to flash slowl y, continue to
hold the HomeLink button, and
f ollow steps 3 thru 6 under
‘‘Training HomeLink’’ (see page ).
If a rolling code transmitter was
previously programmed, the
indicator will f lash rapidly f or 2
seconds, and then stay on f or
about 23 seconds.
Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly.
1. 2.
253
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Erasing Codes
Retraining a Button Customer Assistance
HomeL ink Universal Transceiver
256
——
y

y
() y
y

ÛÝ
Turn the engine off, and confi
rm the
fuel fill cap is installed. If it is, loosen
it, then retighten it until it clicks at
least once. When you c an restart the
engine, the message appears again.
The message goes off after several
days of norm al driving once you
tighten or replace the fuel fill cap. To
scroll to another message, press the
INFO ( / ) button.
If your fuel fill cap is loose or
missing, a ‘‘TIGHTEN FUEL CAP’’
message appears on the multi-
information display after you start
the engine.
Turn the engine off, and confi
rm the
fuel fill cap is installed. If it is, loosen
it, then retighten it until it clicks at
le ast once. When you restart the
engine, the message appears again.
The message goes off after several
days of norm al driving once you
tighten or replace the fuel fill cap. To
scroll to another display, p ress the
Select/Reset knob.
If the system still detects a leak in
your vehicle’s evaporative emissions
system, the malfunction indicator
lamp (MIL) comes on. If the fuel fill
cap was not already tightened, turn
the engine off, and check or
retighten the fuel fill cap until it
clicks at least once. The MIL should
go off after several days of normal
driving once the cap is tightened or
replaced. If the MIL does not go off,
have your vehicle inspected by a
dealer. For more information, see
page .
If the system still detects a leak in
your vehicle’s evaporative emissions
system, the malfunction indicator
lamp (MIL) comes on. If the fuel fill
cap was not already tightened, turn
the engine off, and check or
retighten
the fuel fill cap until it
clicks at least once. The MIL should
go off after several days of normal
driving once the cap is tightened or
replaced. If the MIL does not go off,
have your vehicle inspected by a
dealer. For more inf ormation, see
page . 394
394
On RDX with Technology Package
modelTighten Fuel Cap Message
Service Station Procedure
Bef ore Driving
281
——
yy
() yy

ÛÝ
To display the tire pressure monitor,
press the INFO ( / ) button until
it appears on the multi-inf ormation
display.
When all tire pressures are normal,
the tire pressure monitor will show a
‘‘TIRE PRESS. OK SYSTEM FUNC
NORMAL’’ message. When any of the tires have low
pressure, the low tire pressure
indicator on the instrument panel
comes on, and the multi-inf ormation
display also interrupts the current
display and shows a ‘‘CHECK TIRE
PRESSURE’’ message. You can see
one or more of the low pressure tire
positions highlighted in the display
along with this message.When any of the tires have low
pressure, the tire pressure monitor
shows a ‘‘TIRE PRESS. ERROR
SYSTEM FUNC NORMAL’’
message.
On RDX with Technology Package
model
Tire Pressure Monitoring System (TPMS)
312
INFO BUTTONS
——
y

y
() y
y

If one or more tires have low
pressure, the low tire pressure
indicator on the instrument panel
also comes on (see page ).
It is possible that the pressures
shown on the multi-inf ormation
display and the pressures you
manually measure are slightly
dif f erent.
If the dif f erence is signif icant or you
cannot make the low tire pressure
indicator and message on the multi-
inf ormation display go out af ter
inf lating the tires to the specif ied
values, have your dealer check the
system as soon as possible.
When the TPMS is functioning
normally, you can see the tire
pressure readings of each tire in psi
(U.S. models) or kPa (Canadian
models) by pressing the SEL/
RESET button while the multi-
inf ormation display shows the tire
pressure monitor. If there is a problem with the TPMS,
the multi-information display shows
a ‘‘CHECK TPMS SYSTEM’’
message.
73
CONT INUED
On RDX with Technology Package
model On RDX with Technology Package
model
Tire Pressure Monitoring System (TPMS)
T ire Pressure ReadingsCheck T PMS System Message
Driving
313
U. S.
Canada SEL/RESET BUTTON
——
y
y
() y
y

ÛÝ
Press
and hold the Select/Reset
knob for about 10 seconds. The
engine oil life and the maintenance
item code(s) will blink. Press
the Select/Reset knob for
another 5 seconds. The
maintenance item code(s) will
disappear, and the engine oil life
will reset to ‘‘100.’’ To
see the current engine oil life,
turn the ignition switch to the ON
(II) position, and push and release
the INFO ( / ) button on the
steering wheel repeatedly, until the
engine oil lif e is displayed (see page ).
3.
4.
80
On RDX with Technology Packagemodel
Maintenance Minder
334
ENGINE OIL
LIFE DISPLAY SEL/RESET BUTTONINFO
BUTTONS
——
y
y
() yy

ÛÝ
CONT INUED
When the remaining engine oil lif e is
15 percent or less, the display shows
a ‘‘SERVICE DUE SOON’’ message
along with the maintenance item
code(s) f or other scheduled
maintenance items needing service.The system message indicator on
the instrument panel will also come
on, and a beeper will sound.
To cancel the system message, press
and release the INFO ( / ) button
on the steering wheel. At this time,
the system message indicator will
also be turned of f . Then the display
will change to the engine oil lif e
display. You will see the
maintenance item code(s) along with
the engine oil lif e on the multi-
inf ormation display.
Maintenance Minder
Maint enance
335
SYSTEM MESSAGE INDICATOR
MAINTENANCE ITEM CODE(S)
——
y

y
() yy

ÛÝYou will also see the system
message every time you turn the
ignition switch to the ON (II)
position until your vehicle have the
indicated maintenance perf ormed by
your dealer.
If the indicated maintenance service
is not done and the engine oil lif e
reaches to 0 percent, you will see a
‘‘SERVICE PAST DUE’’ message
along with the maintenance item
code(s) on the multi-inf ormation
display.
To cancel the system message, press
and release the INFO ( / ) button
on the steering wheel. At this time,
the system message indicator will
also be turned of f . Then the display
will change to the engine oil lif e
display. You will see a ‘‘SERVICE’’
message and along with the
maintenance item code(s) on the
multi-inf ormation display.
CONT INUED
Maintenance Minder
Maint enance
337
——
y

y
() yy

ÛÝ
ÛÝ
When you see this message, have
the indicated maintenance done by
your dealer immediately. The system message indicator on
the instrument panel will also come
on, and a beeper will sound.
The system message will appear
again by pressing the INFO ( / )
button af ter cancel it.
You will also see the system
message every time you turn the
ignition switch to the ON (II)
position until your vehicle have the
indicated maintenance perf ormed by
your dealer.
To cancel the system message, press
and release the INFO ( / ) button
on the steering wheel. At this time,
the system message indicator will be turned of f . Then the display
will change to the engine oil lif e
display. You will see the engine oil
lif e blinking and a ‘‘SERVICE’’
message along with the maintenance
item code(s) on the multi-
inf ormation display.
Maintenance Minder
not
338
——
y
y
() yy