Acura RDX 2008 Owner's Manual

´
µ
´
µ
CONT INUED
Each time you pull the (right), the
transmission shifts to a higher gear.
Pull the (lef t) to downshif t. You
will see the selected gear number on
the instrument panel.
When you pull either paddle shif ter,
the gear position indicator shows you
the selected gear number.
When you are driving in D position,
pulling the either paddle shif ter
switches f rom the ordinary
automatic transmission [drive mode
(D)] to the D-paddle shif t mode. You
can shif t the transmission up or
down manually with the paddle
shif ters.
To shif t up or down, use the
(right) or (lef t) paddle shif ter on
each side of the steering wheel.
Downshif ting gives you more power
when climbing, and provides engine
braking when going down a steep hill.
Using the Paddle Shif ters in D
position (D-Paddle Shif t Mode)
Driving with the Paddle Shif ters
Driving
297
GEAR POSITION INDICATOR
\f—\f—\f
y

\f\fy
() 
\fy\f\fy
2008 RDX

The transmission downshif ts to f irst
gear and returns to drive mode (D)
when the vehicle comes to a
complete stop and the vehicle speed
is about 6 mph (10 km/h).
If there is a problem in the
transmission while you are driving
with the paddle shifters, the D
indicator f lashes, the D-paddle shif t
mode is canceled, and the
transmission returns to drive mode
(D).
Each time you pull either paddle
shif ter, the transmission shif ts one
gear up or down. If you want to shif t
up or down more than two gears, pull
the paddle shif ter twice, pause, and
then pull it again. The automatic transmission will not
allow you to change shif t if :
You downshif t bef ore the engine
speed reaches the upper limit of
the lower gear.
If you try to do this, the gear
position indicator will f lash the
numberof thelowergearseveral
times, then return to a higher gear.
You upshif t bef ore the engine
speed reaches the lower limit of
the higher gear.
You press both paddle shif ters at
thesametime.
You press one of the two paddle
shifters with another paddle
shif ter being pressed.
Driving with the Paddle Shif ters
298
\f—\f—\f
y

\f
y
() 
\fy\f\fy
Whenthetransmissionreturnsto
drivemode(D),thedisplayedgear
numbergoesout.
Thetransmissionremainsinthe
selectedgearifyoudonotaccelerate.
The transmission control system
monitors the accelerator pedal use
and your driving conditions. When
you press the accelerator pedal as in
normal driving, the system
judges that you are driving at a
constant cruising speed without
using the paddle shif ters. Under
these conditions, D-paddle shif t
mode is canceled, and the
transmission automatically returns to
drive mode(D).
2008 RDX

´µ
When you move the shif t lever f rom
‘‘D’’ to ‘‘S’’ position and pull either
paddle shif ter, the gear position
indicator displays on ‘‘M’’ along with
the selected gear number.
To upshif t, pull the (right) paddle
shif ter. To downshif t, pull the
(lef t) paddle shif ter. When you accelerate f rom a stop,
the transmission starts in f irst gear,
and you must manually upshif t
between f irst and f if th gears. Make
sure you upshif t bef ore the engine
speed reaches the tachometer’s red
zone.
The transmission remains in the
selectedgear(5,4,3,2,or1).There
is no automatic downshif t when you
push the accelerator pedal to the
f loor.
When you are driving in 4th or 5th
gear, the transmission downshifts to
the lower gear under the f ollowing
conditions:
The vehicle slows down to a
certain speed.
You press the brake pedal.
With the shif t lever in S position, you
can select the sequential shif t mode
to shif t gears; much like a manual
transmission using the paddle
shif ters, but without a clutch pedal.
To enter the sequential shif t mode,
pressthereleasebuttononthefront
of the shift lever, move the lever to
the S position, then pull either paddle
shif ter. To cancel the sequential shif t
mode and return to the ordinary
automatic transmission, move the
shif t lever f rom S position. When
moving the shift lever, be careful not
to operate incorrectly. While you are
driving in the sequential shif t mode,
the transmission will not
automatically return to ordinary
automatic transmission.
CONT INUED
Using the Paddle Shif t in S
position (Sequential Shif t Mode)
Driving with the Paddle Shif ters
Driving
299
‘‘M’’ INDICATOR
GEAR POSITION INDICATOR
\f—\f—\f
y

\fy
() 
\fy\f\fy
2008 RDX

à
à
à
à
à
à
à
à
Downshifting with the paddle shifter
allows you to increase the engine
braking when going down steep or
long hills, and provides more power
when climbing uphills. You can
upshif t the transmission manually to
reduce the rpm. Driving in the
higher gear helps f uel economy.
The transmission also shif ts
automatically as the vehicle comes to
a complete stop. It downshif ts to f irst
gear when the vehicle speed reaches
6mph(10km/h)orless.
To shiftfrom
21
32
43
54 Speed range
under 29 mph (47 km/h)
under 63 mph (100 km/h)
under 94 mph (150 km/h)
under 114 mph (182 km/h)
Here are the speed ranges f or
upshif ting and downshif ting.
To shift from
12
23
34
45 Speed range
over 0 mph (0 km/h)
over 8 mph (13 km/h)
over 17 mph (27 km/h)
over 47 mph (75 km/h)
The automatic transmission will not
allow you to change shif t if :
You downshif t bef ore the engine
speed reaches the upper limit of
the lower gear.
If you try to do this, the gear
position indicator will f lash the
numberof thelowergearseveral
times, then return to a higher gear.
You upshif t bef ore the engine
speed reaches the lower limit of
the higher gear.
You try to shif t to third or a higher
gear when the vehicle is stationary.
You press both paddle shif ters at
thesametime.
You press one of the two paddle
shifters with another paddle
shif ter being pressed.
Driving with the Paddle Shif ters
300
\f—\f—\f
y

\fy
() 
\fy\f\fy
2008 RDX

´
CONT INUED
When you are in sequential shif t
mode, and the vehicle is stopped,
pull the (right) paddle shifter to
shif t to second gear. You will see ‘‘M
2’’ in the display. Starting in second
gear helps to reduce wheelspin in
deep snow or on a slippery surf ace.The super handling-all wheel drive
(SH-AWD) system is a f ull time all-
wheel-drive system that
automatically controls and transfers
varying amounts of engine torque to
all wheels independently, according
to the driving conditions.
While the SH-AWD system helps to
enhance the vehicle’s driving
stability in all situations, it is still
your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. The SH-AWD torque distribution
monitor on the multi-inf ormation
display shows you the amount of
torque being sent to the wheels.
Each wheel: right f ront (RF), lef t
front(LF),rightrear(RR),andleft
rear (LR), has its own torque
indicator.
SH-AWD T orque Distribution
Monitor
Super Handling-A ll Wheel Drive
(SH-AWD) system
Driving with the Paddle Shif ters, Super Handling-A ll Wheel Drive (SH-A WD) System
Driving
St art ing in Second Gear
301
TORQUE INDICATOR
TORQUE INDICATOR
\f—\f—\f
y

\fy
() 
\fy\f\fy
2008 RDX

Your vehicle still has normal f ront-
wheel drive with vehicle stability
assist (VSA), but does not have the
advantages of SH-AWD. Have your
vehicle checked by a dealer as soon
as possible.
If the SH-AWD indicator on the
instrument panel stays on, and the
‘‘CHECK SH-AWD SYSTEM’’
message also appears on the multi-
inf ormation display, there is problem
with the SH-AWD system.
If the SH-AWD indicator blinks while
driving, it indicates the dif f erential
temperature is too high. You will also
see an ‘‘SH-AWD DIFF TEMP
HIGH’’ message on the multi-
inf ormation display. If this happens,
pull to the side of the road when it is
saf e, shif t to Park, and let the engine
idle until the indicator goes out. If
the indicator does not go out, take
your vehicle to a dealer to have it
checked.
Each torque indicator is displayed as
a bar graph divided into 5 segments.
The number of segments represents
the amount of torque distributed to
each wheel.
When there is only a slight change in
torque distribution while driving,
such as cruising on level roads at the
same speed, the torque distribution
monitor may stop displaying the
amount of torque. This is not a
system problem. The monitor will
show the amount if the system
senses any change in torque
distribution.
Super Handling-A ll Wheel Drive (SH-A WD) System
302
\f—\f—\f
y

\fy
() 
\fy\f\fy
2008 RDX

Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly, or
your vehicle may roll if it is parked
on an incline.Make sure the moonroof and the
windows are closed.
If the vehicle is f acing uphill, turn
the front wheels away from the
curb.
If the vehicle is f acing downhill,
turn the front wheels toward the
curb.
Check the indicator on the
instrument panel to verif y that the
security system is set.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
Set the parking brake bef ore you put
the transmission in Park. This keeps
the vehicle from moving and putting
pressure on the parking mechanism
in the transmission.
Turn of f the lights.
Place any packages, valuables, etc.
in the cargo area or take them
with you.
Lock the doors and the tailgate.
Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire.
Parking T ips
Parking
Driving
303
\f—\f—\f
y

\fy
() 
\fy\f\fy
2008 RDX

Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist using negative pressure
generated by the engine and the
electric vacuum pump helps reduce
the ef f ort needed on the brake pedal.
The anti-lock brake system (ABS)
helps you retain steering control
when braking very hard.All f our brakes have audible brake
wear indicators.
The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.
If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, and reduces their ef f ectiveness
and reduces brake pad life. In
addition, f uel economy can be
reduced. It also keeps your brake
lights on all the time, conf using
drivers behind you.
When the electric vacuum pump is in
operation, it makes some mechanical
noises come f rom the engine
compartment. This is normal.
When you drive in cold weather or
thinner air at high altitude, the
electric vacuum pump operates more
f requently af ter the engine is started.
For more inf ormation about the
electric vacuum pump, see page . Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear.
Check your brakes af ter driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious and alert in your driving.
384
Braking System
Brake Pad Wear Indicators
Braking System Design
304
\f—\f—\f
y


\f
y
() 
\fy\f\fy
2008 RDX

The anti-lock brake system (ABS)
helpspreventthewheelsfrom
locking up, and helps you retain
steering control by pumping the
brakes rapidly, much f aster than a
person can do it.
The electronic brake distribution
(EBD) system, which is part of the
ABS, also balances the f ront-to-rear
braking distribution according to
vehicle loading.You will f eel a pulsation in the brake
pedal when the ABS activates, and
you may hear some noise. This is
normal: it is the ABS rapidly
pumpingthebrakes.Ondry
pavement, you will need to press on
thebrakepedalveryhardbeforethe
ABS activates. However, you may
feel the ABS activate immediately if
you are trying to stop on snow or ice.
If this indicator comes on, the anti-
lock f unction of the braking system
has shut down. The brakes still work
like a conventional system, but
without anti-lock. You should have
your dealer inspect your vehicle as
soon as possible.
Let the ABS work f or you by always
keeping f irm, steady pressure on the
brake pedal. This is sometimes
ref erred to as ‘‘stomp and steer.’’ You will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
inf ormation display (see page ).
If the indicator comes on while
driving, test the brakes as instructed
on page .
78
383
CONT INUED
You should never pump the brake pedal.
ABS Indicator
Anti-lock Brakes (ABS)
Driving
305
\f—\f—\f
y


\fy
() 
\fy\f
\fy
2008 RDX

If the ABS indicator and the brake
system indicator come on together,
and the parking brake is f ully
released, the EBD system may also
be shut down.It only helps with the
steering control during braking.
such as trying to take a
corner too f ast or making a sudden
lane change. Always drive at a safe
speed f or the road and weather
conditions.
Always steer moderately
when you are braking hard. Severe
or sharp steering wheel movement
can still cause your vehicle to veer
into oncoming traffic or off the road. on loose or
uneven surf aces, such as gravel or
snow, than a vehicle without anti-
lock.
Test your brakes as instructed on
page . If the brakes f eel normal,
drive slowly and have your vehicle
repaired by your dealer as soon as
possible. Avoid sudden hard braking
which could cause the rear wheels to
lock up and possibly lead to a loss of
control.
The VSA indicator will come on
alongwiththeABSindicator. 383
Anti-lock Brakes (ABS)
Important Saf ety Reminders
A BS does not reduce the time or
distance it takes to stop the
vehicle.
A BS will not prevent a skid that
results f rom changing direction
abruptly,
A BS cannot prevent a loss of
stability. A vehicle with A BS may require a
longer distance to stop
306
\f—\f—\f
y



y
() 
\fy\f

y
2008 RDX