clock Acura RDX 2008 Owner's Manual
[x] Cancel search | Manufacturer: ACURA, Model Year: 2008, Model line: RDX, Model: Acura RDX 2008Pages: 433, PDF Size: 7.4 MB
Page 117 of 433
µ
µ µ
µ
The wiper is not activated.
When you turn the wiper switch to
OFF while the rear window wiper is
in action, it will return to its parked
position.
Rotate the switch clockwise
to turn the rear window wiper ON.
The wiper operates intermittently. When the wiper control lever
position is INT, the rear wiper
operates intermittently. When it is
LO or HI, the rear wiper operates
continuously. The rear window washer uses the
same f luid reservoir as the wind-
shield washer.
When you shif t the transmission to
the reverse position with the f ront
windshield wipers activated, the rear
window wiper operates automatically.
ON
OFF
Rear Window Washer with Wiper
Rear Window Washer Only. Hold past ON to turn the rear
window wiper on and to spray the
rear window washer. The rear
window wiper makes one more
sweep after you release the switch.
Rotate the switch counterclockwise
f rom OFF to spray the window
washer without activating the wiper.
The washer will operate until you
release the switch.
1.
2.
3.
4.
Rear Window Wiper and Washer OFF
ON Rear Window Washer with Wiper
Rear Window Washer Only
Windshield Wipers and Washers
Inst rument s and Cont rols
113
\f—\f—\f
y
y
()
\fy\f
y
2008 RDX
Page 163 of 433
The climate control system in your
vehicle provides a comfortable
driving environment in all weather
conditions.
The standard audio system has
many f eatures. This section
describes those f eatures and how to
use them.
Your vehicle has an anti-theft audio
system that requires a code number
to enable it.
The security system helps to dis-
courage vandalism and thef t of your
vehicle.
Theclimatecontrolsystemandthe
audio system have a voice control
feature. Refer to the navigation
system manual f or more inf ormation................
Climate Control System .160
..........
Dual Temperature Control .165
..............
Climate Control Sensors .167
................................
Audio System .168
.
Audio System (On RDX model) .170
.....
To Play the AM/FM Radio .170
.....
Operating the CD Changer .173
..................
XM
Satellite Radio .183
.................
Adjusting the Sound .186
......................
Setting the Clock .188
Audio System (On RDX with Technology Package ................................
model) .189
.............................
Interf ace Dial.189
......
To Play the AM/FM Radio.190
.....
Operating the CD Changer .196
...................
XM
Satellite Radio.211
..................
Adjusting the Sound.217
.......................
Auxiliary Input Jack .220
............................
Radio Reception .221
..................
Protecting Your Discs .223
.....
CD Changer Error Messages .226
.
Playing the XM
Satellite Radio .228
................
Remote Audio Controls .230
.................
Radio Thef t Protection .232
............................
Security System .233 ...............................
Cruise Control .234
......................................
AcuraLink .237
HomeLink
Universal
................................
Transceiver .247
........
Bluetooth
HandsFreeLink.252
.
Rear View Camera and Monitor .270
On RDX with Technology Package
model
Features
Features
159
\f—\f—\f
y
y
()
\fy\f
y
2008 RDX
Page 190 of 433
µµ´
µ Use the TREBLE/
BASS modes to adjust the tone to
your liking. You can adjust each
mode in levels between 6 and 6.
These two
modes adjust the strength of the
sound coming f rom each speaker.
BALANCE adjusts the side-to-side strength, while FADER adjusts the
front-to-back strength. BALANCE
can be adjusted in levels between L9
and R9. FADER can be adjusted in
levels between F9 and R9. When
FADER adjustment level reaches F9,
the subwoof er speaker will be turned
of f .
Eachmodeisshownonthecenter
display as it changes. Turn the
PWR/VOL knob to adjust the setting
to your liking. When the level
reaches the center, you will see
‘‘ ’’ on the center display. The
system will automatically return the
display to the selected audio mode
about 5 seconds af ter you stop
adjusting a mode.
Press the SOUND/CLOCK button
repeatedly to display the BASS,
TREBLE, FADER, BALANCE,
SUBWOOFER and SVC (speed-
sensitive volume compensation)
settings.
On RDX model
Treble/Bass
Balance/Fader
Adjusting the Sound
Audio System
186
ADJUSTMENT MODE
SOUND/CLOCK BUTTON
ADJUSTMENT LEVEL
U.S. model is shown. PWR/VOL KNOB
\f—\f—\fy
y
()
\fy\f
y
2008 RDX
Page 192 of 433
ChangethehourbypressingtheH
(preset 4) side of the preset bar until
the numbers advance to the desired
time. Change the minute by pressing
the M (preset 5) side of the bar until
the numbers advance to the desired
time.
To set the time, press the SOUND/
CLOCK button until you hear a beep,
then release the button. The
displayed time begins to blink.
You can quickly set the time to the
nearest hour. If the displayed time is
bef ore the half hour, pressing the
SOUND/CLOCK button until you
hear a beep, then pressing the R
(preset 6) side of the preset bar sets
the clock back to the previous hour.
If the displayed time is after the half
hour, the clock sets f orward to the
beginning of the next hour.When you are f inished, press the
SOUND/CLOCK button again to set
the time.
On RDX model
Setting the Clock
Audio System
188
SOUND/CLOCK BUTTON
CLOCK
PRESET 5 (M)
PRESET 4 (H) PRESET 6 (R)
U.S. model is shown.
\f—\f—\f
y
y
()
\fy\f
y
2008 RDX
Page 274 of 433
Whenever you shif t to reverse (R)
with the ignition switch in the ON
(II) position, the rear view is shown
on the navigation system screen.
For the best picture, always keep the
rearview camera clean, and do not
cover the camera lens. To avoid
scratching the lens when you clean it,
use a moist, sof t cloth.Since the rearview camera display
area is limited, you should always
back up slowly and caref ully, and
look behind you f or obstacles.
When in reverse, the navigation
buttons are locked out, except the
interf ace dial on the dashboard. Turn
the dial clockwise to make the
camera image brighter, and counter-
clockwise to darken the image.
On RDX with Technology Package
model
Rearview Camera and Monitor
270
INTERFACE DIAL
The camera brightness cannot be
adjusted by voice control.
\f—\f—\f
y
\fy
()
\fy\fy
2008 RDX
Page 345 of 433
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.Pour coolant into the reserve tank.
Fill it half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Make sure the engine and radiator
are cool.
Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise. Put the radiator cap back on, and
tighten it fully.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spills immediately; it
could damage components in the
engine compartment.
2.
1. 4. 5.
6.
3.
Engine Coolant
Maint enance
341
RESERVE TANK
RADIATOR CAP
MAX
MIN
\f—\f—\f
y
y
()
\fy\fy
2008 RDX
Page 351 of 433
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied technician.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Open the hood.
1.
2. 3.
4.
5.
Headlight A iming
L ow Beam Headlight Bulb
Replacement
Replacing a High Beam Headlight
Bulb
Lights
Maint enance
347
BULB CONNECTORHalogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
\f—\f—\f
y
y
()
\fy\fy
2008 RDX
Page 352 of 433
Test the lights to make sure the
new bulb is working.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Remove the bulb f rom the socket
by pushing the bulb in and turning
it counterclockwise until it unlocks.
Open the hood. Remove the
socket f rom the headlight
assembly by turning it one-quarter
turn counterclockwise. Open the hood. Remove the
socket f rom the headlight
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
1.
2.
3. 1.
2.
4.
5.
Lights
Replacing a Front T urn Signal/
Parking L ight Bulb
Replacing a Front Side Marker
Light Bulb
348
BULB
SOCKET SOCKET BULB
\f—\f—\f
y
\fy
()
\fy\fy
2008 RDX
Page 353 of 433
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.
Install the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
1.
2. 3.
4.
3.
4.
CONT INUED
Lights
Replacing Rear Bulbs
(in Tailgate)
Maint enance
349
COVER
NOTCH SOCKETS
BULBS
\f—\f—\f
y
y
()
\fy\fy
2008 RDX
Page 354 of 433
Determine which of the three
bulbs is burned out: brake/
taillight, turn signal or rear side
marker.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the tailgate.
Remove the two bolt covers on the
rear pillar by prying on the bottom
edge with a flat-tip screwdriver.
Remove the bolts with a Phillips-
head screwdriver, and remove the
light assembly f rom the rear pillar.
Turn on the lights to make sure
the new bulb is working.
Reinstall the light assembly cover.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
2. 4.
5.
3.
1.
5.
6.
7.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
350
COVERS
BULB SOCKET
BOLTS
\f—\f—\f
y
y
()
\fy\fy
2008 RDX