remove seats Acura RDX 2008 Owner's Manual

Position the lap part of the belt as
low as possible across your hips,
then pull up on the shoulder part of
the belt so the lap part f its snugly.
This lets your strong pelvic bones
take the force of a crash and reduces
the chance of internal injuries.
If necessary, pull up on the shoulder
belt again to remove any slack, then
check that the belt rests across the
center of your chest and over your
shoulder.This spreads the f orces of a crash
over the strongest bones in your
upper body.
If the seat belt touches or crosses
your neck, or if it crosses your arm
instead of your shoulder, you need to
adjust the seat belt anchor height.
The front seats have adjustable seat
belt anchors. To adjust the height of
an anchor, press and hold the release
button and slide the anchor up or
down as needed (it has f our
positions).
CONT INUED
Protecting A dults and Teens
Driver and Passenger Saf ety
15
RELEASE
BUTTON
Improperly positioning the seat
belts can cause serious injury
or death in a crash.
Make sure all seat belts are
properly positioned before
driving.
\f—\f—\f
y

y
() 
\fy\f\f\fy
2008 RDX

Whatever type you have, f ollow
the child seat maker’s instructions
f or adjusting or tightening the f it.
Remove the cargo area cover, and
place it on the cargo area f loor
(see page ).Lif t the head restraint (see page
), then route the tether strap
through the legs of the head
restraint and over the seat-back,
making sure the strap is not
twisted.
Other LATCH-compatible seats have
a f lexible-type connector as shown
above.
Place the child seat on the vehicle
seat, then attach the seat to the
lower anchors according to the
child seat maker’s instructions.
Some LATCH-compatible seats
have a rigid-type connector as
shown above.
5. 6.
4.
3.
158133
Installing a Child Seat
46
Flexible type
Rigid type TETHER STRAP
\f—\f—\f
y
y
() 
\fy\f\f
y
2008 RDX

To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button,
then pull the restraint out of the seat-
back.When reinstalling a head restraint,
put the legs back in place. Then
adjust it to the appropriate height
while pressing the release button.
Make sure the removed head
restraints are securely stored.
Seats
Removing t he Head Rest raint
134
Rear
CUSHION
SEAT BACK
LEGS
RELEASE BUTTON
Failure to reinstall the head
restraints can result in severe
injury during a crash.
Always replace the head
restraints before driving.
\f—\f—\f
y

y
() 
\fy\f
y
2008 RDX

The rear seat armrest is in the
center of the rear seat. Pivot it down
to use it.Remove any items from the seat
before folding down the seat-back.
Make sure there are no items on the
f loor bef ore f olding down the seats.
The lid of the console compartment
canbeusedasanarmrest. The rear seat-backs can be f olded
down to give more cargo room. Each
side f olds down separately. So you
can still carry a passenger in the rear
seat.
Folding the Rear Seats Down
Armrests
Seats
136
Front Rear
\f—\f—\f
y
y
() 
\fy\f

y
2008 RDX

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. This keeps the
f loor mat f rom sliding f orward and
possibly interf ering with the pedals.
If you remove the driver’s f loor mat,
make sure to re-anchor it when you
putitbackinyourvehicle.A non-Acura f loor mat may not f it
your vehicle properly. This could
prevent the proper operation of the
f olding rear seats and the passenger’s
seat weight sensors. We recommend
using genuine Acura f loor mats. Do
not put additional f loor mats on top
of the anchored mat.
Cleaning the Seat Belts Floor Mats
Cleaning the Seat Belts, Floor Mats
354
LOOP
FLOOR MAT ANCHORS
\f—\f—\f
y

\fy
() 
\fy\fy
2008 RDX