lock Acura RL 2002 3.5 Repair Manual

Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Put the drain cap back in place
tightly, then reinstall the clip on
the drain cap securely.
On the right side of the engine
block, remove the clip with a plier,
andthenremovethedraincap. 5.
4. 6.
Cooling Syst em
Maint enance234
C CL
LIIPP
D
D R
RAA I
INN C
CAA P
P
R
REES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K H
HO
OL LDD E
ER
R
01/09/28 20:03:39 31SZ3660_237

The air cleaner element should be
cleaned or replaced according to the
time and distance recommendations
in the maintenance schedule.
Clean the air cleaner element by
blowing compressed air through it in
the opposite direction to normal air
f low. If you do not have access to
compressed air (such as a service
station), ask your Acura dealer to do
this service.
Follow the replacement procedure
for removal and reinstallation.
Always use Honda Power Steering
Fluid. If it is not available, you may
use another power steering f luid as
an emergency replacement.
However, continued use can cause
increased wear and poor steering in
cold weather. Have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently and have
the system inspected as soon as
possible. Clean the hood latch assembly with a
mild cleaner, then lubricate it with a
multipurpose grease. Lubricate all
the moving parts (as shown),
including the pivot. Follow the time
and distance recommendations in
the Maintenance Schedule. If you
are not sure how to clean and grease
the latch, contact your Acura dealer.
CONT INUED
A ir Cleaner Element
Hood L atch
Maint enance
Power Steering, Hood L atch, A ir Cleaner Element
Cleaning (Severe Condit ions)
241
P P I
IVV O
OT TS
S
L
LA A T
TC
CH H
A
A S
SSSEEM
M B
BLLYY
T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.
01/09/28 20:04:54 31SZ3660_244

Put the new spark plug into the
socket, then screw it into the hole.
Screw it in by hand so you do not
crossthread it.
Use a wrench to remove the two
bolts holding the ignition coil.
Remove the ignition coil by pulling
it straight out.
Remove the spark plug with
a f ive-eighths inch (16 mm) spark
plug socket.
Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
4. 5.
6.7.
Spark Plugs
Maint enance244
I IG
GN NIITT I
IOON N C
COOI ILL
I
IG
GN NIITT I
IOON N C
COOI ILL
L
LO OC CKK T
TA
A B
BC
CO
ON NNNEEC
CT TO
OR R B
BO
OL LTT S
S
01/09/28 20:05:25 31SZ3660_247

Install the ignition coil. Reinstall
the two hold-down bolts.
Repeat this procedure f or the
other f ive spark plugs.
Torque the spark plug. (If you do
not have a torque wrench, tighten
the spark plug two-thirds of a turn
af ter it contacts the cylinder head.)
Tightening torque: Put the A/C tube back in place.
Install the tower bar and tighten
the two bolts and the f our nuts.
Tightening torque:
Push the wire connector onto the
ignition coil. Make sure it locks in
place. Install the engine cover. First
tighten the two bolts on the front
of the engine cover, then tighten
the three nuts on the engine cover.
Tightening torque:
8. 9.
10.
11. 12.
13.
14.
CONT INUED
Spark Plugs
Maint enance245
13 lbf·ft (18 N·m , 1.8 kgf·m) 16 lbf·ft (22 N·m , 2.2 kgf·m)
7 lbf·ft (9.8 N·m , 1.0 kgf·m)
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.
01/09/28 20:05:37 31SZ3660_248

µ
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
To replace the blade:
Turn the ignition ON (II), switch
the wipers to INT or (low
position), then turn the ignition
OFF when the wiper arm is
approximately midway in its travel. 2.
1.
CONT INUED
Wiper Blades
Maint enance249
W WI IPP E
ER
R A
AR
RMM S
S
L
LOOC CKK
T
T A
A B
B
01/09/28 20:06:10 31SZ3660_252

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Turn the ignition switch ON (II)
and return the windshield wipers
to their park position.
3. 4. 5.
6.
7.
Wiper Blades
Maint enance250
B BL
LAA D
DE
E B
BLLAA D
DE
E
R
RE EI
INNF FOOR RCCEEM
M E
EN
NT T
01/09/28 20:06:18 31SZ3660_253

Run the air conditioning at least once
a week during the cold weather
months. Run it f or at least ten
minutes while you are driving at a
steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the ref rigerant.If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the
system with Ref rigerant HFC-134a
(R-134a). (See Specif ications on page
.)
Periodically check the engine’s
radiator and air conditioning
condenser f or leaves, insects, and
dirt stuck to the f ront surf ace. These
block the air f low and reduce cooling
ef f iciency. Use a light spray f rom a
hose or a sof t brush to remove them. Your car’s air conditioning is a sealed
system. Any major maintenance,
such as recharging, should be done
by a qualif ied mechanic. You can do
a couple of things to make sure the
air conditioning works ef f iciently. 312
A ir Condit ioning Syst em
Maint enance251
A A I
IRR C
COON NDDI
ITT I
IOON NIINNG G C
COON NDDE
EN
NS SEER
R
Whenever you have the air conditioning
system serviced, make sure the service
f acility uses a ref rigerant recycling
system. This system captures the
ref rigerant f or reuse. Releasing
ref rigerant into the atmosphere can
damage the environment.
The condenser and radiator f ins bend
easily. Only use a low-pressure spray
or sof t-bristle brush to clean them.
01/09/28 20:06:26 31SZ3660_254

To remove the f ront turn signal/
parking light bulb, push it in
slightly and turn it
counterclockwise. To remove the
side marker bulb, pull it straight
out of its socket.
Install the new bulb into the
socket.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise. Pull the inner f ender cover back.
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left. Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter. Testthelightstomakesurethe
new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
1. 2. 3.
4.5.
6.
7.
8.
9.
Lights
Maint enance
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
265
H H
O
OL LDD I
INNG G C
CLLIIPP
01/09/28 20:08:43 31SZ3660_268

Open the trunk.Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
Undo the f astener on the side of
the trunk lining by pushing on the
center of the f astener’s head until
it pops in. Pull the lining back. Remove the socket by turning it one-quarter turn counterclockwise. Determine which of the f our bulbs
is burned out: stop/taillights, back-
up light, or turn signal.Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.
1.
3. 2.4.
5.
6.
7.
Replacing Rear Bulbs
Lights
Maint enance266
F FA
A S
STTE
EN
NE ER
R
01/09/28 20:08:54 31SZ3660_269

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Reset the f astener by pushing on
the pointed end until it pops back
almost f lush with the f ingers on
the housing.
Put the f astener in the hole in the
side of the trunk lining and push
on the center until it locks (the
center is f lush with the head). Reinstall the socket. Turn it
clockwise until it locks.
Install the new bulb in the socket. Remove the bulb by pushing it in
slightly and turning it counter-
clockwise. Testthelightstomakesurethe
new bulb is working.
1.
2.
8.
9. 3.
4.
Replacing a High-mount Brake
Light Bulb
Lights
Maint enance267
01/09/28 20:09:06 31SZ3660_270