light Acura RL 2006 User Guide

ÛÝ
Multi-Inf ormation Display
Inst rument s and Cont rols
85
Press the or button.
Press the SEL/RESET button.ADAPTIVE CRUISE
CONTROL SET UP
seepage86
METER SET
UP
seepage91
POSITION
SET UP
see page100
KEYLESS
ACCESS SET UP
see page105
LIGHTING
SET UP
see page112
DOOR/WINDOW
SET UP
see page119
WIPER SET
UP
see page130

ÛÝÛÝ
While the multi-information display
is in the ACC SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display. Press the SEL/RESET button. The
screen changes as shown above. The
highlighted unit, mph or km/h, is
the current setting. To change the
setting, press the INFO ( / )
button until the unit you want is
highlighted, then press the SEL/
RESET button.
To change the unit of measurement
f rom mph to km/h, do this:
CONT INUED
Multi-Inf ormation Display
A dapt ive Cruise Cont rol Display
Speed Unit
Inst rument s and Cont rols
89

ÛÝÛ
Ý
While the multi-information display
is in the METER SETUP of the
CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display. Press the SEL/RESET button. The
screen changes as shown above. The
highlighted number is the current
setting above or below the outside
temperature. Press the INFO ( /
) button repeatedly until the
number you want appears, then
press the SEL/RESET button to
enter your selection.
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions:
Multi-Inf ormation Display
A djust Outside T emp. Display
94

Û
Ý
ÛÝ Û
Ý
ÛÝ
CONT INUED
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO ( / ) button, then press the SEL/
RESET button.
Multi-Inf ormation Display
K EYL ESS A CCESS Setup
Inst rument s and Cont rols
105
Press the or button.
Press the SEL/RESET button. seepage106
seepage108
seepage110

ÛÝÛÝ
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.
The same exterior lights blink once
when you lock the doors by touching
the door lock sensor while carrying
the remote.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
Multi-Inf ormation Display
K eyless A ccess L ight Flash
108

ÛÝ
To exit KEYLESS ACCESS LIGHT
FLASH without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the
keyless access light f lash setup.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109

ÛÝÛ
Ý
ÛÝ
ÛÝ
There are three settings in the
lighting setup:INTERIOR LIGHT
DIMMING TIME
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select LIGHTING SETUP by
pressing the INFO ( / ) button,
then press the SEL/RESET button. AUTO LIGHT SENSITIVITY HEADLIGHT AUTO OFF TIMER
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Multi-Inf ormation Display
Lighting Setup
112
Press the or button.
Press the SEL/RESET button. see page113
seepage115
seepage117

ÛÝ
While the multi-information display
is in the LIGHTNING SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to the above display.
Press the SEL/RESET button. The
screen changes as shown above.
Select how long you want the lights
to stay on bef ore they f ade out (60,
30, or 15 seconds) by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
The interior lights f ade out when you
close all doors and the trunk. To
change how long the lights stay on
before they fade out, follow these
instructions:
CONT INUED
Multi-Inf ormation Display
Int erior L ight Dimming T ime
Inst rument s and Cont rols
113

ÛÝ
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY. If this
happens, you need to repeat the
interior light dimming time setup.To exit INTERIOR LIGHT
DIMMING TIME without changing
the current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
Multi-Inf ormation Display
114

ÛÝÛÝ
The headlights, parking lights, side
marker lights, taillights, and license
plate light go of f af ter the selected
time when you close the driver’s
door and take the remote with you.
To change how long the lights stay
on before they go off, follow these
instructions:
While the multi-information display
is in the LIGHTING SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select how long you want the lights
to stay on bef ore they go of f (60, 30,
or 15 seconds) by pressing the INFO
( / ) button, then press the SEL/
RESET button to enter your
selection.
CONT INUED
Multi-Inf ormation Display
Headlight A uto Of f T imer
Inst rument s and Cont rols
115