Acura RL 2007 Owner's Manual

The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off. Pressing this button also
turns the rear window defogger on
and off.
When
you finish, move the
selector switch to the center (off)
position. This turns off the
adjustment switch so you can’t
move a mirror out of position by
accidentally bumping the switch.
Outside mirror positions can be
stored in the driving position
memory system (see page ). Depending on the position of the
selector switch, the lef t or right side
mirror will pivot downward slightly
when you shif t the transmission into
reverse. In the lef t position, the lef t
mirror pivots. In the right position,
the right mirror pivots. This gives
you a better view of that side of the
vehicle while parallel parking. The
mirror returns to its original position
when you take the transmission out
of reverse. To turn this f eature of f ,
leave the switch in the center
position.
3.
160
Mirrors
Power Mirror HeatersReverse Tilt Door Mirror
Inst rument s and Cont rols
159
HEATED MIRROR BUTTON
——
y
y
(y
y

Store a driving position only when
the vehicle is parked.
Adjust the steering wheel to a
comfortable position (see page
).
Adjust the outside mirrors for best
visibility (see page ).
Adjust
the seat to a comfortable
position (see page ).
Your vehicle has a memory feature
f or the steering wheel, driver’s seat,
and outside mirror positions.
Two seat, steering wheel, and
outside mirror positions can be
stored in separate memories. You
select a memorized position by
pushing the appropriate button.
Press the MEMO button on the
driver’s door. You will hear a beep.
The indicator in the memory
buttons (1 and 2) will blink.
Immediatelypressoneof the
memory buttons (1 or 2) until you
hear two beeps. The indicator in
the memory button will stay on.
The current positions of the
driver’s seat, steering wheel, and
outside mirrors are now stored.
Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
3.
1.
2.
155
147 159
Storing a Driving Position in
Memory
Driving Position Memory System
160
MEMORY
BUTTONS
MEMO BUTTON
——
y
y
(y
y

To select a memorized position, do
this: Press
the desired memory button
(1 or 2) until you hear a beep.
The system will move the seat,
steering wheel, and outside mirrors
to the memorized positions. The
indicator in the selected memory
button will flash during movement.
When the adjustments are complete,
you will hear two beeps, and the
indicator will remain on.
Make sure the shift lever is in
Park. To change the ‘‘MEMORY
POSITION LINK’’ setting, see page
.
To cancel the storing procedure
after pressing the MEMO button:
Do not press a memory button
within 5 seconds.
Readjust the outside mirror
position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. Readjust the seat or steering
position.
1. 2.
104
CONT INUED
Selecting a Memorized Position
Driving Position Memory System
Inst rument s and Cont rols
161
MEMORY BUTTONS
——
y
y
(y
y

Press any button on the control
panel: MEMO, 1, or 2.
Adjust the outside mirrors. Shif t out of Park. Push any of the adjustment
switches f or the seat or steering
wheel.
If you select a memorized position
without pushing the ignition switch
knob or inserting the built-in key in
the ignition switch, only the seat and
outside mirrors will adjust. To get
the system to also adjust the steering
wheel, push and turn the ignition
switch or insert the built-in key in
the ignition switch. You will hear two
beeps when it is complete. You can use the adjustment switches
to change the positions of the seat,
steering wheel, or outside mirrors
af ter they are in their memorized
position. If you change the
memorized position, the indicator in
the memory button will go out. To
keep this driving position f or later
use, you must store it in the driving
position memory.
To stop the system’s automatic
adjustment, do any of the f ollowing:
Driving Position Memory System
162
——
y


y
(y
y

Your vehicle has a keyless access
system. When you carry the remote
with you, you can lock/unlock the
door(s), unlock the trunk, and start
the engine without using the built-in
key.
The system may not work if:Thebatteryof theremoteisweak.
You carry a cell phone, a laptop
computer, or other electrical
device near the remote. There is strong electrical current
nearby.
The remote is covered by metal.
A vehicle is being operated with a
transmitter nearby.
When the remote battery is dead. Protect the remote and the built-in
key f rom direct sunlight, high
temperature, and high humidity.
Always keep the remote and the
built-in key away from any magnetic
material.
Youshouldhavereceivedakey
number tag with your built-in key.
You will need this key number if you
ever have to get a lost key replaced.
Use only Acura-approved key blanks.
When the vehicle battery is dead.
Make sure the driver always carries
the remote/built-in key set. Do not drop the remote or the
built-in key, and do not set heavy
objects on them.
The built-in keys do not contain
batteries. Keep the remote and the built-in key
away f rom liquids. If they get wet,
dry them immediately with a sof t
cloth.
K eyless A ccess System
Inst rument s and Cont rols
163
——
y
y
(y
y

This remote is used to lock/unlock the
doors and unlock the trunk.
When you carry the remote, you can
lock/unlock the doors, unlock the
trunk, and start the engine without a
key.
You can lock/unlock the doors
within about 32 inches (about 80 cm)
radius from the outside door handle.
The
following keys come with your
vehicle. Refer to page for how to
separate the keys.
This key is used to lock/unlock the
doors, glove box, trunk pass-through
cover, and to start the engine (after
you remove the ignition switch cover,
see page ). You can open the trunk within about
32 inches (about 80 cm) radius f rom
thetrunkreleaseswitch. Anyone can lock/unlock a door or
open the trunk if the remote is
within the operating range of the
door or the trunk.
Theremotemaynotworkif:
It is too close to the vehicle.
It is above or below the vehicle,
even when it is within its operating
range.
174 177
Keys
K eyless A ccess System
Built -in K ey
K eyless A ccess Remot e
164
BUILT-IN KEYS OPERATING
RANGE
KEY NUMBER TAG KEYLESS ACCESS
REMOTES
——
y
y
(y
y

The handle of each front door has a
sensor. That sensor works with the
remote so you can automatically
unlock/lock the door(s).
To change the ‘‘DOOR UNLOCK
MODE’’ setting, see page . Wh
en you unlock the door(s), some
exterior lights blink twice and the
system beeps twice.
To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
.
To change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page .
By default, only the driver’s door
unlocks when you grab its handle. All
the doors unlock when you grab
the handle of the front passenger’s
door.
If you wear a glove while grabbing a
front door handle, the door sensor
maybeslowtorespondormaynot
respond by unlocking the doors.
If you do not open any of the doors
within 30 seconds, they will
automatically relock.
To change the ‘‘SECURITY
RELOCK TIMER’’ setting, see page .
If a remote is within operating range
while you wash your vehicle or when
it is raining heavily, the door sensors
may respond by unlocking the doors.
The unlock sensors do not operate
when: Theremoteisnotwithinthe
operating range.
The remote is too close to the
vehicle.
When the doors are unlocked.
Theremotebatteryisdead.
The vehicle battery is dead.
109 111
113131
Unlocking the Door(s)
K eyless A ccess System
Inst rument s and Cont rols
165
——
y
y
(y
y

Each front door has a LOCK/
UNLOCK feature.
When you touch the door lock
sensor of the front door by hand, all
the doors and the trunk will lock. The
lock sensors do not operate if:
When you lock the doors, some
exterior lights blink once and the system
beeps once. When you
cannot set the security system
because the trunk or hood is open,
no exterior light blinks and/or no
beeper sounds.
Befo re locking the doors, make sure
theremoteisnotinside thevehicle.If
a remote is within operating range
while you wash your vehicle or when
it is raining heavily, the door sensors
may respond by locking the doors.
Wi
thin 2 seconds of touching the
handle to lock the doors or locking
the doors with remote, pull the
handletomakesurethe doorsare
actually locked. The door unlock
sensors do not operate for about 2
seconds after the doors are locked.
To
change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page .
To
change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
. If you touch the door lock sensor of
the f ront door with your hand
wearing a glove, the door sensor may
delay to respond or not respond by
locking the doors.
Theremoteisnotwithinthe
operating range.
The doors are open.
The ignition switch is not in the
LOCK (0) position.
The built-in key is in the ignition
switch.
The remote is too close to the
vehicle.
Theremotebatteryisdead.
The vehicle battery is dead.
111
113
L ocking the Doors
K eyless A ccess System
166
DOOR LOCK SENSOR
——
y
y
(y

y

Bef ore closing the trunk, make sure
theremoteisnotinthetrunk.
If you close the trunk when the
remote is in it, the system beeps, and
the trunk reopens.
When you close the trunk with all
doors locked, the trunk will lock.
When you unlock all the doors with
the remote, built-in key or power
door lock master switch, the trunk
will unlock.
Use the pull handle when you close
the trunk.
If you open a door, pull its lock tab,
and shut it when the remote is inside
the vehicle, the driver’s door unlock.
Make sure you carry the remote
with you when you lock the doors.
K eyless A ccess System
Locking the TrunkDoor L ock Prevent ion
Inst rument s and Cont rols
167
PULL HANDLE
——
y
y
(y
y

µ
The
trunk cannot be locked if:
When the trunk is locked, you can
open it in any of these ways: Press
this button once to
lock all doors. Some exterior lights
will flash. When you push the LOCK
button twice within 5 seconds, you
will hear a beep to verify that the
doors are locked and the security
system is set.
Pull the trunk release switch when
carrying the remote (the system
beeps once).
Press
the trunk button on the
remote. Press the trunk release button
inside the vehicle. Keep
the trunk lid closed at all times
while driving to avoid damaging the
lid, and to prevent exhaust gas f rom
getting into the interior. See on page .
The remote is too close to the
seatback of the rear seat or the
seat cushion. Theremoteisontheinteriorrear
panel. The remote is too close to the
trunk lid.
56
K eyless A ccess System
L ocking and Unlocking the T runk K eyless A ccess Remote
LOCK
Carbon
Monoxide Hazard
168
LED
UNLOCK
BUTTON PANIC
BUTTON
TRUNK
RELEASE
BUTTON
LOCK
BUTTON
TRUNK RELEASE SWITCH
——
y

y
(y
y