reset Acura RL 2008 Manual Online

When cruise control is on while
driving, the pressure reading cannot
be checked by the tire pressure
monitor on the multi-inf ormation
display.
When the TPMS is functioning
normally, you can see the tire
pressure readings of each tire in psi
(U.S. models) or kPa (Canadian
models) by pressing the SEL/
RESET button while the multi-
inf ormation display shows the tire
pressure monitor.
If the low tire pressure/TPMS
indicator and the low tire position on
the low tire pressure monitor do not
go out after inflating the tires to the
specified values, have your dealer
check the system as soon as possible.
If one or more tires have low
pressure, the low tire pressure/
TPMS indicator on the instrument
panel also comes on (see page ).371
Tire Pressure Monitoring System (TPMS)
T ire Pressure Readings
374
CANADA
U.S.
\f—\f—
y\f
y
(\fy\fy
2008 RL

The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle turns
more or less than desired. It also
assists you in maintaining traction
while accelerating on loose or
slippery road surf aces. It does this
by regulating the engine’s output and
by selectively applying the brakes.When VSA activates, you will see the
VSA activation indicator blink (see
page ).
If this indicator comes on while
driving, pull to the side of the road
when it is saf e, and turn of f the
engine. Reset the system by
restarting the engine. If the VSA
system indicator stays on or comes
back on while driving, have the VSA
system inspected by your dealer.
If the indicator does not come on
when the ignition switch is turned to
the ON (II) position, there may be a
problem with the VSA system. Have
your dealer inspect your vehicle as
soon as possible (see page ).When the VSA system indicator
comes on, you will also see a
‘‘CHECK VSA SYSTEM’’ message
on the multi-information display.
Without VSA, your vehicle still has
normal braking and cornering ability,
but it does not have VSA traction and
stability enhancement.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. There may also
be some noise f rom the VSA
hydraulic system. You will also see
the VSA activation indicator blink.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. If the low tire pressure/TPMS
indicator comes on (see page ),
or the multi-information display
shows a ‘‘CHECK TPMS SYSTEM’’
message with the indicator flashing
(see page ), the VSA system
automatically turns on even when
the VSA system is turned of f with
the VSA OFF switch. In this case,
you cannot turn the VSA system of f
by pressing the VSA OFF switch
again.
65
65 371
375
VSA A ctivation Indicator
VSA System Indicator
Vehicle Stability Assist (VSA) System
Driving
377
\f—\f—
y\f\fy
(\fy\fy
2008 RL

µ
µ
µ
µ
µ
µ
µ
µ
µ
µµ
µ
One of the most convenient and
important f eatures of the multi-
inf ormation display on your vehicle
is the maintenance minder.
Based on engine operating
conditions and accumulated engine
revolutions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e.
The system also displays the code
f or other scheduled maintenance
items needing service.
To see the remaining engine oil lif e
displayed on the lower right corner
on the multi-information display as a
percentage, turn the ignition switch
to the ON (II) position, and press the
SEL/RESET button on the steering
wheel repeatedly until the engine oil
lifeappears(seepage ).The remaining engine oil lif e is
displayed according to the table
shown below.
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%
10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%)
100% 90%
80%
70%
60%
50%
40%
30%
20%
15%
10%
5%
0%
73
CONT INUED
Maintenance Minder
Engine Oil L if e Display
Maint enance
387
REMAINING ENGINE OIL LIFE
\f—\f—
y\f
y
(\fy\fy
2008 RL

ÝÛÝÛ
The message will be canceled if the
or buttononthesteeringwheel
is pressed. Press the or button
to see the message again.
When the remaining engine oil lif e is
15 to 6 percent, the multi-inf ormation
display shows a ‘‘SERVICE DUE
SOON’’ message along with the
maintenance schedule code
indicating the main and sub items
required at the time of the oil change.
Refer to page and for a
complete list of the maintenance
main items and sub items. Press the SEL/RESET button on the
steering wheel repeatedly to select
the engine oil lif e. The message
‘‘OIL LIFE’’ along with the
percentage of oil lif e remaining and
the maintenance item code(s),
appear on the lower part of the multi-
inf ormation display.
395 396
Maintenance Minder
388
MESSAGE
MAINTENANCE
MAIN ITEM REMAINING
ENGINE OIL LIFE
MAINTENANCE
ITEM CODE (S)
MAINTENANCE
SUB ITEM (S)
——
y
y
(yy
2008 RL

ÝÛÝÛ
The message will be canceled if the
or buttononthesteeringwheel
is pressed. Press the or button
to see the message again.
When the remaining engine oil lif e is
1 to 5 percent, the multi-information
display shows a ‘‘SERVICE DUE
NOW’’ message with the
maintenance items. When you see
this message have the indicated
maintenance perf ormed as soon as
possible. Press the SEL/RESET button on the
steering wheel repeatedly to select
the engine oil lif e. The message
‘‘SERVICE OIL LIFE’’, along with
‘‘5%’’, and the maintenance item
code(s) are displayed on the lower
part of the multi-inf ormation display
when the calculated engine oil lif e is
1 to 5 percent (see page ).
387
CONT INUED
Maintenance Minder
Maint enance
389
\f—\f—
y\fy
(\fy\fy
2008 RL

ÝÛÛÝ
Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
mode will be shown on the multi-
inf ormation display.
To reset the engine oil lif e, press
the or button on the steering
wheel to select RESET on the
display, and press the SEL/
RESET button. To cancel resetting the oil life,
press the or button on the
steering wheel to select CANCEL
on the display, and press the SEL/
RESET button.
If you do not complete the reset
procedure within 30 seconds af ter
selecting the reset mode, the mode
will be canceled automatically.
Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100%’’ on the display the
next time you turn the ignition
switch to the ON (II) position.
If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:
If the oil lif e minder is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it is.
Turn the ignition switch to the ON
(II) position.
The maintenance item code or codes
indicate the main and sub items
required at the time of the oil change
(see page ).
1.
2.
3.
395
Maintenance Minder
390
U.S.
CANADA
\f—\f—
y\fy
(\fy\fy
2008 RL

ÝÛÝÛ
Immediately have the service
perf ormed, and make sure to reset
the oil lif e minder as previously
described.
The message will be canceled if the
or buttononthesteeringwheel
is pressed. Press the or button
to see the message again.
If the indicated maintenance service
is not done and the remaining engine
oil lif e reaches 0 %, the multi-
inf ormation display will show the
message ‘‘SERVICE PAST DUE’’
and the maintenance item code(s).
This message is displayed when the
total mileage is less than 10 miles
(f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%. Press the SEL/RESET button on the
steering wheel repeatedly to select
the engine oil lif e minder. The
message ‘‘SERVICE OIL LIFE’’,
along with ‘‘0%’’, and the
maintenance item code are displayed
on the lower part of the multi-
inf ormation display when the
calculated engine oil lif e is 0 percent.
CONT INUED
Maintenance Minder
Maint enance
391
\f—\f—
y\fy
(\fy\fy
2008 RL

ÝÛÝÛ
And also, the percentage ‘‘0’’ keeps
blinking on the display.
If the indicated required service is
not done and the remaining engine
oil lif e becomes 0 %, the multi-
inf ormation display will show a
‘‘SERVICE PAST DUE’’ message,
thetotalmileageaftertheremaining
oillifebecame0%,andthe
maintenance item code(s).This message is displayed when you
drive over 10 miles (f or U.S. models)
or 10 km (f or Canadian models)
af ter seeing the 0 % message.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
The message will be canceled if the
or buttononthesteeringwheel
is pressed. Press the or button
to see the message again.
This particular message is displayed
whenthemileageaftertheengineoil
lifebecame0%reaches10miles(for
U.S. models)/10 km (f or Canadian
models).
The maximum total mileage shown
with this message is ‘‘9999 mile’’ (f or
U.S. models) or ‘‘9999 km’’ (f or
Canadian models).
Maintenance Minder
392
U.S.
CANADAMAINTENANCE ITEM CODE (S)TOTAL PAST DUE MILEAGE
\f—\f—
y\fy
(\fy\fy
2008 RL

µ
µ
This particular message is displayed
when you drive over 10 miles (f or
U.S. models) or 10 km (f or Canadian
models) af ter seeing 0 %.
When you press the SEL/RESET
button to select the engine oil lif e
minder, the message ‘‘SERVICE’’,
along with the maintenance item
code and the total negative mileage
aftertheoillifebecame0percent,
will be displayed on the lower part of
the multi-information display. The maximum total negative mileage
is ‘‘ 9999 mile’’ (f or U.S. models) or
‘‘ 9999 km’’ (f or Canadian models).
If you have the required service
perf ormed but do not reset the
display, or reset the display without
perf orming the service, the system
will not show the proper
maintenance intervals. This can lead
to serious mechanical problems
because you will no longer have an
accurate record of when
maintenance is needed.
Your authorized Acura dealer knows
your vehicle best and can provide
competent, ef f icient service.
CONT INUED
Maintenance Minder
Important Maintenance
Precautions
Maint enance
393
U.S.
CANADA
TOTAL PAST DUE MILEAGE
\f—\f—
y\f\fy
(\fy\fy
2008 RL

Î
Ì Ì
Ì
Î
CONT INUED
Maintenance Minder
395
:
If the message ‘‘SERVICE DUE NOW’’ does not appear more than 12 months
after the display is reset, change the engine oil every year.
See information on maintenance and emissions warranty on page .
Independent of the maintenance messages in the Multi-Information
Display, replace the brake fluid every 3 years.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy.
NOTE: 1:
394
Maintenance Main Items
Replace engine oil
Replace engine oil and oil filter
Inspect front and rear brakes
Check parking brake adjustment
Inspect these items: Tie rod ends, steering gear box, and boots
Suspension components
Driveshaft boots
Brake hoses and line (including ABS)
All fluid levels and condition of fluids
Exhaust system
Fuel lines and connections
A
B
Symbol1
Maintenance Minder
\f—\f—
y\fy
(\fy\f\f\fy
2008 RL