display Acura RL 2010 Owner's Manual

The security system will not set if
the hood, trunk, or any door is not
f ully closed. If the system will not set,
check the Door and Trunk Open
monitor on the instrument panel (see
page ) to see if the doors and
trunk are f ully closed. Since it is not
part of the monitor display, manually
check the hood.
Do not attempt to alter this system
or add other devices to it.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking/side marker
lights, and taillights f lash if someone
attempts to break into your vehicle
or remove the radio. This alarm
continues f or 2 minutes, then the
system resets. To reset an alarming
system bef ore the 2 minutes have
elapsed, unlock either f ront door
with the remote or the built-in key.
With the system set, you can still
open the trunk with the remote
without triggering the alarm. The
alarm will sound if the trunk lock is
f orced, or the trunk is opened with
the trunk release button on the
driver’s door or the emergency trunk
opener.
Once the security system is set,
opening any door or the hood
without using the built-in key or the
remote will cause it to sound. It also
sounds if the radio is removed f rom
the dashboard or the audio system
wiring is cut.
The security system automatically
sets 15 seconds after you lock the
doors, close the hood, and close the
trunk. For the system to activate,
you must lock the doors f rom the
outside with the remote, built-in key,
lock tab, or door lock switch. The
security system indicator on the
instrument panel starts blinking
immediately to show you the system
is setting itself . 13
Security System
Features
315
SECURITY SYSTEM INDICATOR
——y

y
(yy
2010 RL

Cruise control allows you to maintain
asetspeedabove25mph(40km/h)
without keeping your f oot on the
accelerator pedal. It should be used
f or cruising on straight, open
highways. It is not recommended f or
city driving, winding roads, slippery
roads, heavy rain, or bad weather.Push in the CRUISE button or the
ACC button (models with adaptive
cruise control) on the steering
wheel. The CRUISE MAIN or
green ACC indicator (models with
ACC) indicator on the instrument
panel comes on.
To switch f rom ACC to cruise
control, press the distance buttonon the steering wheel, and hold it
f or 1 second (see page ).
Accelerate to the desired cruising
speedabove25mph(40km/h).
Press and release the SET/
DECELbuttononthesteering
wheel. The CRUISE CONTROL
icon appears on the multi-
inf ormation display to show the
system is now activated.
1. 2.
3.
333
On models with adaptive cruise
control
Using Cruise Control
Cruise Control
316
RES/
ACCEL
BUTTON
CRUISE (ACC) BUTTON
SET/
DECEL
BUTTON
Non-ACC model is shown
Improper use of the cruise
control can lead to a crash.
Use the cruise control only
when traveling on open
highways in good weather.
——y

y
(y
y
2010 RL

You can increase the set cruising
speed in any of these ways:You can decrease the set cruising
speed in any of these ways:
Press and hold the RES/ACCEL
button. When you reach the
desired cruising speed, release the
button.
Push on the accelerator pedal.
Accelerate to the desired cruising
speed, then press the SET/
DECEL button. Press and hold the SET/DECEL
button. Release the button when
you reach the desired speed.
To increase your speed in very
small amounts, tap the RES/
ACCEL button. Each time you do
this, the vehicle speeds up about 1
mph (1.6 km/h).
Cruise control may not hold the set
speed when you are going up and
down hills. If your speed increases
going down a hill, use the brakes to
slow down. This will cancel cruise
control. On models with adaptive
cruise control (ACC), this also
causes the cruise control icon on the
multi-inf ormation display to go of f
and the cruise mode icon to come on.
To resume the set speed, press the
RES/ACCEL button. The CRUISE
CONTROLicononthemulti-
inf ormation display will come back
on.
To slow down in very small
amounts, tap the SET/DECEL
button. Each time you do this,
your vehicle will slow down about
1 mph (1.6 km/h).
Tap the brake pedal lightly with
your f oot. The CRUISE
CONTROLicononthemulti-
inf ormation display will go out.
When the vehicle slows to the
desired speed, press the SET/
DECEL button.
CONT INUED
Changing the Set Speed
Cruise Control
Features
317
——y

y
(yy
2010 RL

Adaptive cruise control (ACC)
consists of a radar sensor in the
f ront grille, the ACC buttons on the
steering wheel, and the ACC
f unctions of the multi-inf ormation
display.
The radar sensor for ACC is shared
with the collision mitigation brake
system (CMBS). For more
inf ormation on the radar sensor, see
page . For more inf ormation on
CMBS, see page .413
414
If equipped
A CC Components
A daptive Cruise Control (A CC)
Features
319
ACC INDICATOR
MULTI-INFORMATION
DISPLAY
ACC BUTTON
DISTANCE BUTTONSET/DECEL
BUTTON
RES/ACCEL BUTTON
CANCEL BUTTON
——y

y
(yy
2010 RL

Adaptive cruise control (ACC) allows
you to maintain a set speed and keep
the vehicle ahead of you and your
vehicle at a saf e distance without
having to use the accelerator pedal
or the brake pedal.If the vehicle ahead of you slows
down suddenly or another vehicle
cuts in f ront of your vehicle, ACC
alerts you by sounding a beeper and
displaying a message on the multi-
inf ormation display.
TheACCradarsensorinthefront
grille can detect and monitor the
distance of a vehicle up to 328 f eet
(100 meters) ahead of your vehicle.
For more inf ormation on the radar
sensor, see page .Do not use ACC under these
conditions:
In poor visibility.
In heavy traffic.
When you must slow down and
speed up repeatedly.
On winding roads.
When you enter a toll gate,
interchange, service area, parking
area, etc. In these areas, there is
no vehicle ahead of you, and ACC
would still try to accelerate to your
set speed.
In bad weather (rain, f og, snow,
etc.)
On a slippery road (f or example a
road covered with ice or snow).
As with any system, there are limits
to ACC. Inappropriate use of ACC
can result in a serious accident. Use
the brake pedal whenever necessary,
and always keep a safe distance
between your vehicle and other
vehicles.
When the vehicle ahead of you slows
down or speeds up, ACC senses the
change in distance and compensates
by accelerating or braking your
vehicle to reach the cruising speed
you previously set. The distance
between vehicles is based on your
speed: the f aster you go, the longer
the distance will be; the slower you
go, the shorter it will be.
414
Overview
Important Saf ety Precautions
A daptive Cruise Control (A CC)
320
——y

y
(yy
2010 RL

If the vehicle ahead of you slows
down abruptly, or if another vehicle
cuts in f ront of you, a beeper sounds
and a message appears on the multi-
inf ormation display to warn you.Your vehicle f ollows the vehicle
ahead of it, keeping a constant
distance. ACC will not keep your
vehicle at a constant distance if the
vehicle ahead of you goes out of
range of your set speed.If the vehicle ahead of you slows
down and changes lanes, ACC no
longer tracks it. Your vehicle will
then return to your set speed.
In this case, decelerate your vehicle
by pressing the brake pedal, and
keep an appropriate distance f rom
the vehicle ahead.
When a vehicle ahead is within ACC
range and going at a steady speed
A daptive Cruise Control (A CC)
322
——y

y
(yy
2010 RL

ACC does not work below 25 mph
(40 km/h). It cannot bring your
vehicle to a complete stop.
ACC will not sound a beeper or
display a message on the multi-
inf ormation display to warn you of
vehicles going slower than 13 mph
(20 km/h) or vehicles that are
parked. In these cases, it is up to
you to maintain a safe distance by
using the brake pedal.
ACC may not recognize
motorcycles or other small
vehicles ahead of your vehicle.ACC may react to vehicles beside
you or even a building beside you
by momentarily applying the
brakes or sounding a beeper under
conditions such as a sudden curve
or narrowing of the road, an
abrupt movement of the steering
wheel, or if you are in an unusual
position within your lane.
Limitations
A daptive Cruise Control (A CC)
Features
323
——y

y
(yy
2010 RL

Push the ACC button on the
steering wheel. The ACC indicator
on the instrument panel comes on,
and ‘‘ACC’’ is shown on the multi-
inf ormation display.
Accelerate to the desired speed
above25mph(40km/h).Press and release the SET/
DECELbuttononthesteering
wheel, then release the
accelerator pedal.
If you press the SET/DECEL button
when the vehicle speed is below 25
mph (40 km/h), you will hear a beep
about 1 second. This means ACC is
not activated, and you cannot set
your speed. When your speed reaches 25 mph
(40 km/h), ACC goes into wait mode,
and ‘‘ACC’’ is shown on the multi-
inf ormation display.
1.
2. 3.
Using the ACC
A daptive Cruise Control (A CC)
324
ACC BUTTON
SET/DECEL BUTTON
——y

y
(yy
2010 RL

When the speed is set, it is shown
along with a vehicle icon and
distance bars on the multi-
inf ormation display.
Refertopage forhowtosetand
change the set distance between
your vehicle and the vehicle ahead of
you.If you change the speed unit
measurement f rom the f actory
def ault setting, the initial speed unit
measurement is shown under the
current unit.
To change the speed unit
measurement f rom mph to km/h,
see page .
328 92
A daptive Cruise Control (A CC)
Features
325
SET VEHICLE
SPEED
U.S.
CANADA CANADA U.S.
SET VEHICLE
DISTANCE INITIAL SPEED
UNIT
——y

y
(yy
2010 RL

The set speed can be increased by
using the RES/ACCEL button or the
accelerator pedal.To increase the set speed with the
RES/ACCEL button, do this:
Press and hold the RES/ACCEL
button. The vehicle will accelerate.
When you reach the speed you want,
release the button.
To increase your speed in small
amounts, tap the RES/ACCEL
button repeatedly. Each time you do
this, your vehicle will speed up about
1 mph (1 km/h).
While the vehicle accelerates to the
set speed, the set speed on the multi-
inf ormation display will f lash.
If a vehicle ahead of you is driving at
a slower speed than the speed you
want to set, your vehicle will not
accelerate; it will keep some distance
between your vehicles.To increase the set speed with the
accelerator pedal, do this:
Press the accelerator pedal to
increase to the speed you want, then
press the SET/DECEL button. The
set speed will be shown on the multi-
inf ormation display. If you do not
press the SET/DECEL button, your
vehicle will return to the previously
set speed.
The ACC beeper will not sound
while you press the accelerator pedal,
no matter how close you get to the
vehicle ahead of you.
Increasing the Set Speed
A daptive Cruise Control (A CC)
326
RES/ACCEL BUTTON
——y

y
(y
y
2010 RL