ECU Acura RL 2010 User Guide

To deactivate the lockable retractor
andremoveachildseat,unlatchthe
buckle, unroute the seat belt, and let
the belt fully retract.
Push and pull the child seat
f orward and f rom side-to-side to
verify that it is secure enough to
stay upright during normal driving
maneuvers. If the child seat is not
secure, unlatch the belt, allow it to
retract f ully, then repeat these
steps.
Af ter conf irming that the belt is
locked, grab the shoulder part of
the belt near the buckle, and pull
up to remove any slack from the
lap part of the belt. Remember, if
the lap part of the belt is not tight,
the child seat will not be secure.
To remove slack, it may help to
putweightonthechildseat,or
push on the back of the seat while
pulling up on the belt. 5.
4.
Installing a Child Seat
50
——y
y
(yy
2010 RL

A child seat with a tether can be
installed in any seating position in
the back seat, using one of the
anchorage points shown above.
Since a tether can provide additional
security to the lap/shoulder belt
installation, we recommend using a
tether whenever one is required or
available.Lift the anchor cover, then attach
the tether strap hook to the
anchor, making sure the strap is
not twisted.
Tighten the strap according to the
seat maker’s instructions.
Af ter properly securing the child
seat with the lap/shoulder belt
(see page ), pivot the head
restraint down (see page ) and
route the tether strap over the
head restraint.
1. 2.
3.
22 157
Installing a Child Seat
Installing a Child Seat with a
Tether
Driver and Passenger Saf ety
51
COVER
ANCHOR
TETHER ANCHORAGE P
OINTS
TETHER STRAP HOOK
ANCHOR
——y


y
(yy
2010 RL

If you decide that a child can saf ely
ride up f ront, be sure to:Caref ully read the owner’s manual,
and make sure you understand all
seat belt instructions and all saf ety
inf ormation.
Move the vehicle seat to the rear-
most position.
Have the child sit up straight, back
against the seat, and feet on or
near the f loor.
Check that the child’s seat belt is
properly and securely positioned.
Supervise the child. Even mature
children sometimes need to be
reminded to f asten the seat belts
or sit properly.
Of course, children vary widely. And
while age may be one indicator of
when a child can saf ely ride in f ront,
there are other important f actors you
should consider.
If the passenger’s front airbag
inf lates in a moderate to severe
f rontal collision, the airbag can cause
serious injuries to a child who is
unrestrained, improperly restrained,
sitting too close to the airbag, or out
of position.
A side airbag also poses risks. If any
part of a larger child’s body is in the
path of a deploying side airbag, the
child could receive possibly serious
injuries. The National Highway Traffic Safety
Administration and Transport
Canada recommend that all children
age 12 and under be properly
restrained in a back seat. Physically, a child must be large
enough f or the lap/shoulder belt to
properly f it (see pages and ). If
the seat belt does not f it properly,
with or without the child sitting on a
booster seat, the child should not sit
in f ront.
To saf ely ride in f ront, a child must
be able to f ollow the rules, including
sitting properly, and wearing the seat
belt properly throughout a ride.5217
Protecting L arger Children
Physical Size
Maturity
When Can a L arger Child Sit in
Front
54
——y
y
(yy
2010 RL

Î
ÎÎ
Î
Î
The U.S. instrument panel is shown. Dif f erences f or the Canadian models are noted in the text. If equipped.
:
Instrument Panel
Inst rument s and Cont rols
61
SEAT BELT REMINDER
INDICATOR
CHARGING SYSTEM
INDICATOR KEYLESS ACCESS
SYSTEM INDICATOR
LOW OIL PRESSURE
INDICATOR MALFUNCTION INDICATOR
LAMP
LOW FUEL INDICATORELECTRONICALLY
CONTROLLED
POWER STEERING
SYSTEM (ECPS)
INDICATOR
LIGHTS ON INDICATOR
FOG LIGHT INDICATOR
MULTI-INFORMATION
DISPLAY MESSAGE INDICATOR
SECURITY SYSTEM
INDICATOR
(P.64)
(P.68)
(P.68)
(P.69)
(P.71)
(P.21,62) (P.68)
ANTI-LOCK BRAKE
SYSTEM (ABS)
INDICATOR
(P.34, 63)
SUPPLEMENTAL RESTRAINT SYSTEM
(SRS) INDICATOR
VEHICLE STABILITY ASSIST (VSA)
SYSTEM INDICATOR
VSA
ACTIVATION
INDICATOR
HIGH BEAM
INDICATOR
SIDE AIRBAG OFF
INDICATOR(P.35,
63)
(P.65) (P.65)
IMMOBILIZER SYSTEM
INDICATOR PARKING BRAKE
AND BRAKE SYSTEM
INDICATOR(P.64)
SH-AWD INDICATOR (P.66)
LOW TIRE PRESSURE/TPMS INDICATOR(P.66)
ADAPTIVE FRONT LIGHTING SYSTEM
(AFS) INDICATOR ADAPTIVE CRUISE CONTROL (ACC)
INDICATOR
(P.65) /
CRUISE MAIN INDICATOR
COLLISION MITIGATION BRAKE
SYSTEM (CMBS) INDICATOR (P.
69)
(P.69, 144) (P.66,
319)
(P.62, 500)
(P.62, 501)
(P.62, 500)
(P.67, 423) (P.63,
502)
(P.64,
411)
(P.65,
429)
(P.429)
——y
y
(yy
2010 RL

This indicator comes on when the
security system is set. For more
inf ormation, see page .
This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position.
Itcomesonasareminderthatyou
have turned off the adaptive front
lighting system (AFS).
This indicator blinks when there is a
problem with the AFS system; you
will also see a ‘‘CHECK ADAPTIVE
FRONT LIGHTING SYSTEM’’
message on the multi-inf ormation
display (see page ). If this
happens, stop the vehicle in a saf e
place, turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, and restart the engine. If
the indicator does not go of f or
blinks again, take your vehicle to a
dealer to have it checked. For more
inf ormation, see page .
This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. It also comes on as areminder that you have turned of f
the collision mitigation brake system
(CMBS).
The CMBS indicator also comes on
if dirt or other debris blocks the
radar sensor in the f ront grille. You
will also see a ‘‘CHECK CMBS
RADAR SENSOR’’ message on the
multi-inf ormation display. When you
clean the radar sensor, the indicator
should go of f the next time you turn
the ignition switch to the ON (II)
position.
If the indicator comes on at any
other time, there is a problem with
the CMBS. You will also see a
‘‘CHECK CMBS SYSTEM’’ message
on the multi-information display. If
this happens, take your vehicle to a
dealer, and have it checked. For
more information, see page .
When this indicator is on, the CMBS
is not working.
78
144 315
418
If equipped
If equipped
A daptive Front L ighting
System (A FS) IndicatorSecurity System Indicator
Collision Mitigation
Brake System (CMBS)
Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
69
SECURITY SYSTEM INDICATOR
——y
y
(yy
2010 RL

ÎÎ
Î
Î Î
Î CUST OMIZE MENU
DOOR/WINDOW
SETUP
(see page 122)
WIPER SETUP
(see page 133) AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMER
WIPER ACTION
SHIFT TO P
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 SEC
60 SEC
30 SEC
INTERMITTENT
WITH VEH SPD
SETPage
125
127
129
131
134
85
CHG SETTING
(see page 87)
DEFAULT ALL
(see page 85) Description
Changes when the doors
automatically unlock.
Changes which doors unlock with the
f irst push of the remote’s unlock
button.
The exterior lights flash each time
you press the LOCK or UNLOCK
button.
Changes how long it takes (in
seconds) f or the doors to relock and
the security system to set after you
unlock the driver’s door without
opening it.
Changes the wiper operation among
two settings when the wiper switch is
in the INT position.
Changes all settings to the default.
: Default setting
CUST OMIZE GROUP
CANCEL
CUSTOMIZE ENTRYCUSTOMIZE SET UP
Multi-Inf ormation Display
84
——y

y
(yy
2010 RL

Û
Ý
Û
Ý
ÛÝ
ÛÝ
AUTO DOOR LOCK
AUTO DOOR UNLOCK
There are five settings to choose
f rom in the door/window setup:
While CUSTOMIZE GROUP is
shown on the multi-inf ormation
display, select DOOR/WINDOW
SETUP by pressing the INFO ( /
) button, and then press the SEL/
RESET button.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. SECURITY RELOCK TIMER DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
Door/Window Setup
Multi-Inf ormation Display
122
seepage123
seepage125
seepage127
seepage129
see page 131
Press the or button.
Press the SEL/RESET button.
——y
y
(y
y
2010 RL

µµ
µ ÛÝ
There are three settings you can
choose f rom:
SHIFT FROM P
The doors lock whenever you move
the shift lever out of Park.
WITH VEH SPD
The doors lock when the vehicle
speed reaches about 10 mph (about
15 km/h).
OFF
The auto door lock mode is
deactivated all the time.
While DOOR/WINDOW SETUP is
shownintheCUSTOMIZEGROUP
of the multi-information display,
press the SEL/RESET button. You
will see the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select the desired setting by
pressing the INFO ( / ) button,
then press the SEL/RESET button
to enter your selection.
CONT INUED
A ut o Door L ock
Multi-Inf ormation Display
Inst rument s and Cont rols
123
——y
y
(y
y
2010 RL

ÛÝ
µ
µ ÛÝ
µ
There are three settings you can
choose f rom:
While DOOR/WINDOW SETUP is
shownintheCUSTOMIZEGROUP
of the multi-information display,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.
SHIFT TO P The driver’s door or
all the doors, depending on the door
lock mode setting (see page ),
unlock when you move the shif t
lever to Park.
IGN OFF The driver’s door or all
the doors, depending on the door
lock mode setting (see page ),
unlock when you turn the ignition
switch to the LOCK (0) position.
Press the SEL/RESET button. The
screen changes as shown above.
Select the desired setting by
pressing the INFO ( / ) button,
then press the SEL/RESET button
to enter your selection.
OFF The auto door unlock mode
is deactivated all the time. 127
127
CONT INUED
A ut o Door Unlock
Multi-Inf ormation Display
Inst rument s and Cont rols
125
——y
y
(y
y
2010 RL

ÛÝÛÝ
When you press the LOCK button
on the remote to lock the doors and
the trunk, and then press the button
again within 5 seconds, a beeper
sounds once and the exterior lights
blink once to verif y that the doors
arelockedandthesecuritysystemis
set.
While the multi-information display
is in the DOOR/WINDOW SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
When you press the UNLOCK
button on the remote to unlock the
doors, the exterior lights blink twice
to verify that the doors are unlocked
and the security system is turned of f .
To turn this feature on or off, follow
these instructions.
CONT INUED
K eyless L ock A cknowledgement
Multi-Inf ormation Display
Inst rument s and Cont rols
129
——y
y
(y
y
2010 RL