transmission Acura RL 2010 User Guide

µIf you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone. Make sure the ignition switch is in
the LOCK (0) position. Set the parking brake.
This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work.
To shift into the S
position, press the release button on
the front of the shift lever, and move
the lever to S. This position is similar
to D, except only gears f rom f irst to
f ourth are selected. The S position
keeps the transmission f rom cycling
between fourth and fifth gears in
stop-and-go driving.
With the shift lever in D or S, you
canalsousethepaddleshiftersto
shif t the transmission up or down.
Once you begin to use the paddle
shif ters in S, the transmission will no
longer upshif t or downshif t
automatically. For more inf ormation
of driving with the paddle shif ters,
see page . 1.
2.
403
CONT INUED
Engine Speed Limiter Shift Lock Release
S Position (S)
Automatic Transmission
Driving
401
——y
y
(yy
2010 RL

If you need to use the shif t lock
release, it means your vehicle is
developing a problem. Have the
vehicle checked by a dealer.
Put a cloth on the edge of the shif t
lock release slot cover next to the
shif t lever. Use a small f lat-tip
screwdriver or a metal f ingernail
f ile to remove the cover. Caref ully
pry on the edge of the cover. Push down on the built-in key
while you press the release button
and move the shif t lever out of
Park to neutral.Remove the built-in key from the
shif t lock release slot, then
reinstall the cover. Make sure the
notchonthecoverisonthedriver’s
side. Press the brake pedal, and
restart the engine.
Insert the built-in key into the shift
lock release slot.
3.
4.
5.6.
Automatic Transmission
402
COVER
SHIFT LOCK RELEASE SLOT
——y
y
(yy
2010 RL

´
µ
´
µ Each time you pull (right), the
transmission shifts to a higher gear.
Pull (lef t) to downshif t. You will
see the selected gear number on the
instrument panel.
To shif t up or down, use the
(right) or (lef t) paddle shif ter on
either side of the steering wheel.
WhenyouaredrivingintheD
position, pulling either paddle shif ter
switches f rom the ordinary
automatic transmission [drive mode
(D)] to the D-paddle shif t mode. You
can shif t the transmission up or
down manually with the paddle
shif ters.
When you pull either paddle shif ter,
the gear position indicator shows you
the selected gear number.
Downshif ting gives you more power
when climbing, and provides engine
braking when going down a steep hill.
CONT INUED
Using the Paddle Shif ters in the
D position (D-Paddle Shif t Mode)
Driving with the Paddle Shif ters
Driving
403
GEAR POSITION INDICATOR
PADDLE SHIFTERS
——y

y
(yy
2010 RL

The transmission control system
monitors the accelerator pedal use
and your driving conditions. When
you press the accelerator pedal as in
normal driving, the system judges
that you are driving at a constant
cruising speed without using the
paddle shif ters. Under these
conditions, D-paddle shif t mode is
canceled, and the transmission
automatically returns to drive mode
(D).If there is a problem in the
transmission while you are driving
with the paddle shifters, the D
indicator f lashes, the D-paddle shif t
mode is canceled, and the
transmission returns to drive mode
(D).
Each time you pull either paddle
shif ter, the transmission shif ts one
gear up or down. If you want to shif t
up or down more than two gears, pull
the paddle shif ter twice, pause, and
then pull it again. The transmission remains in the
selected gear if you do not accelerate. When the transmission returns to
drive mode (D), the displayed gear
number disappears. The automatic transmission will not
allow you to shif t up or down if :
You downshif t bef ore the engine
speed reaches the highest
threshold of the lower gear.
If you try to do this, the gear
position indicator will f lash the
numberof thelowergearseveral
times, then return to a higher gear. The transmission downshif ts to f irst
gear and returns to drive mode (D)
when the vehicle comes to a
complete stop and the vehicle speed
is about 9 mph (15 km/h).
You upshif t bef ore the engine
speed reaches the lowest
threshold of the higher gear.
You pull both paddle shif ters at
thesametime.
You pull one of the two paddle
shifters with another paddle
shif ter being pressed.
Driving with the Paddle Shif ters
404
——y

y
(yy
2010 RL

´µ
When you move the shif t lever f rom
‘‘D’’ to ‘‘S’’ position and pull either
paddle shif ter, the gear position
indicator displays ‘‘M’’ along with the
selected gear number.
To upshif t, pull the (right) paddle
shif ter. To downshif t, pull the
(lef t) paddle shif ter. When you accelerate f rom a stop,
the transmission starts in f irst gear,
and you must manually upshif t
between f irst and f if th gears. Make
sure you upshif t bef ore the engine
speed reaches the tachometer’s red
zone.
The transmission remains in the
selectedgear(5,4,3,2,or1).There
is no automatic downshif t when you
push the accelerator pedal to the
f loor.
When you are driving in 4th or 5th
gear, the transmission downshifts to
the lower gear under the f ollowing
conditions:
The vehicle slows down to a
certain speed.
You press the brake pedal.
With the shif t lever in the S position,
you can select the sequential shif t
mode to shif t gears; much like a
manual transmission using the
paddle shif ters, but without a clutch
pedal.
To enter the sequential shif t mode,
pressthereleasebuttononthefront
of the shift lever, move the lever to
the S position, then pull either paddle
shif ter. To cancel the sequential shif t
mode and return to the ordinary
automatic transmission, move the
shif t lever f rom the S position. When
moving the shift lever, be careful not
to operate incorrectly. While you are
driving in the sequential shif t mode,
the transmission will not
automatically return to ordinary
automatic transmission.
CONT INUED
Using the Paddle Shif ters in the S
position (Sequential Shif t Mode)
Driving with the Paddle Shif ters
Driving
405
GEAR POSITION INDICATOR
‘‘M’’ INDICATOR
——y

y
(y
y
2010 RL

à
à
à
à
à
à
à
à
Downshifting with the paddle shifter
allows you to increase the engine
braking when going down steep or
long hills, and provides more power
when climbing uphills. You can
upshif t the transmission manually to
reduce the rpm.
To Shift
from
12
23
34
45
Here are the speed ranges f or
upshif ting and downshif ting.
The automatic transmission will not
allow you to shif t up or down if :
You downshif t bef ore the engine
speed reaches the highest
threshold of the lower gear.
If you try to do this, the gear
position indicator will f lash the
numberof thelowergearseveral
times, then return to a higher gear.
Also, you cannot upshif t with the
paddle shif ter bef ore the engine
speed reaches the lower limit of
the higher gear.
You try to shif t to third or a higher
gear when the vehicle is stationary.
You pull one of the two paddle
shifters with another paddle
shif ter being pressed. You pull both paddle shif ters at
thesametime. Speed range
over 0 mph (0 km/h)
over 9 mph (15 km/h)
over 17 mph (27 km/h)
over 38 mph (60 km/h)
Speed range
under 131 mph (210 km/h) under 94 mph (150 km/h)
under 63 mph (100 km/h) under 31 mph (50 km/h)
To Shift
from
54
43
32
21
The transmission also shif ts
automatically as the vehicle comes to
a complete stop. It downshif ts to f irst
gear when the vehicle speed reaches
9mph(15km/h)orless.
Driving with the Paddle Shif ters
406
——y

y
(y

y
2010 RL

Check the indicator on the
instrument panel to verif y that the
security system is set. If the vehicle is f acing downhill,
turn the front wheels toward the
curb. If the vehicle is f acing uphill, turn
the front wheels away from the
curb. Never park over dry leaves, tall
grass, or other f lammable
materials. The hot three way
catalytic converter could cause
these materials to catch on fire.
Make sure the parking brake is
f ully released bef ore driving away.
Driving with the parking brake
partially set can overheat or
damage the rear brakes.
Always use the parking brake when
you park your vehicle. Make sure
the parking brake is set f irmly or
your vehicle may roll if it is on an
incline.
Set the parking brake bef ore you put
the transmission in Park. This keeps
the vehicle from moving and putting
pressure on the parking mechanism
in the transmission.
Make sure the moonroof and the
windows are closed.
Turn of f the lights.
Place any packages, valuables, etc.,
in the trunk or take them with you.
Lock the doors.
Parking T ips
Parking
Driving
409
——y

y
(y
y
2010 RL

Crosswinds and air turbulence
caused by passing trucks can disrupt
your steering and cause the trailer to
sway. When being passed by a large
vehicle, keep a constant speed, and
steer straight ahead. Do not try to
make quick steering or braking
corrections.
Follow all normal precautions when
parking, including f irmly setting the
parking brake and putting the
transmission in Park. Also, place
wheel chocks at each of the trailer’s
tires.
When climbing hills, closely watch
your temperature gauge. If it nears
the red (Hot) mark, turn the air
conditioning of f , reduce speed and, if
necessary, pull to the side of the
road to let the engine cool.
Always drive slowly and have
someone guide you when backing up.
Grip the of the steering
wheel; turn the wheel to the lef t to
get the trailer to move to the lef t,
andturnthewheelrighttomovethe
trailer to the right.Your vehicle is not designed to be
towed behind a motor home. If your
vehicle needs to be towed in an
emergency, see page .
If you must stop when f acing uphill,
use the f oot brake or parking brake.
Do not try to hold the vehicle in
placebypressingontheaccelerator,
as this can cause the automatic
transmission to overheat.
When driving down hills, reduce
your speed, and shif t down to S
position, or use the paddle shif ters to
the lower gear (3, 2 or 1) in the S
position. When towing a trailer, do
not ‘‘ride’’ the brakes, and remember,
it will take longer to slow down and
stop when towing a trailer. 513
bottom
Backing Up
Handling Crosswinds and Buf f et ing
Parking
Driving on Hills
Towing Your Vehicle
Towing a Trailer, Towing Your Vehicle
436
——y
y
(y
y
2010 RL

This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
If you have the skills and tools to
perf orm more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer. This section also includes
instructions on how to read the
maintenance minder messages on
the multi-information display, and
instructions f or simple maintenance
tasks you may want to take care of
yourself .......................
Maintenance Saf ety .438
....................
Maintenance Minder . 439
..............................
Fluid Locations .449
......
Engine Compartment Covers . 450
........................
Adding Engine Oil .452
Changing the Engine Oil and ...........................................
Filter .453
..............................
Engine Coolant .455
....................
Windshield Washers .458
....
Automatic Transmission Fluid . 458
....................................
Brake Fluid .460
....................
Power Steering Fluid . 460
....................................
Timing Belt .461
.............................................
Lights .462
..................
DustandPollenFilter . 470
................
Cleaning the Seat Belts . 470
.....................................
Floor Mats .471
.................................
Wiper Blades .472
...........................................
Wheels .474
...............................................
Tires .474
...................
Checking the Battery . 483
.............................
Vehicle Storage .486
535
Maintenance
Maint enance
437
——y
y
(yy
2010 RL

µµµ
µ
µ
µ
Ì Engine oil level Check every
time you f ill the f uel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
you f ill the f uel tank. See page .
Automatic transmission Check
the f luid level monthly. See page
.
Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
and license plate lights monthly.
See page . Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page .
Brakes Check the f luid level
monthly. See page .
U.S. Vehicles:
According to state and federal
regulations, f ailure to perf orm
maintenance on the items marked
with will not void your emissions
warranties. However, Acura
recommends that all maintenance
services be perf ormed in accordance
with the intervals indicated by the
multi-inf ormation display.
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the appropriate
page listed.
We recommend using Acura parts
and fluids whenever you have
maintenance done. These are
manuf actured to the same high
quality standards as the original
components, so you can be conf ident
of their perf ormance and durability. Your authorized dealer knows your
vehicle best and can provide
competent, ef f icient service.
However, service at a dealer is not
mandatory to keep your warranties
in effect. Maintenance may be done
by any qualif ied service f acility or
person who is skilled in this type of
automotive service. Keep all receipts
as proof of completion, and have the
person who does the work f ill out
your Maintenance Journal or
Canadian Maintenance Log. Check
your warranty booklet f or more
inf ormation. 383
383
458 460
474
462
Maintenance Minder
Maintenance, replacement, or
repair of emissions control
devices and systems may be done
by any automotive repair
establishment or individual using
parts that are ‘‘certif ied’’ to EPA
standards.
Owner’s Maintenance Checks
446
——y
y
(y
y
2010 RL