display Acura RL 2010 Workshop Manual

ÛÝ
To exit AUTO TILT &
TELESCOPIC without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the auto
tilt and telescopic setup.
Multi-Inf ormation Display
Inst rument s and Cont rols
107
——y


y
(y

y
2010 RL

Û
Ý
ÛÝ Û
Ý
ÛÝ
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the custom setting then press the
SEL/RESET button to enter your
selection. There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO ( / ) button, then press the SEL/
RESET button. K eyless A ccess Setup
Multi-Inf ormation Display
108
seepage109
seepage111
seepage113
Press the or button.
Press the SEL/RESET button.
——y

y
(y

y
2010 RL

ÛÝ
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select DRIVER DOOR ONLY or
ALL DOORS by pressing the INFO
( / ) button, then press the SEL/
RESET button to enter your
selection.
CONT INUED
Door Unlock Mode
Multi-Inf ormation Display
Inst rument s and Cont rols
109
——y

y
(y

y
2010 RL

ÛÝ
To exit DOOR UNLOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the door
unlock mode setup.
Multi-Inf ormation Display
110
——y

y
(y

y
2010 RL

ÛÝÛÝ
When KEYLESS ACCESS LIGHT
FLASH is set to ON, some exterior
lights blink twice when you unlock
thedoorsbygrabbingthedriver’s
door handle while carrying the
remote.
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.
The same exterior lights blink once
when you lock the doors by touching
the door lock sensor while carrying
the remote.
Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
CONT INUED
K eyless A ccess L ight Flash
Multi-Inf ormation Display
Inst rument s and Cont rols
111
——y
y
(y

y
2010 RL

ÛÝ
To exit KEYLESS ACCESS LIGHT
FLASH without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
keyless access light f lash setup.
Multi-Inf ormation Display
112
——y

y
(y

y
2010 RL

ÛÝÛÝ
When KEYLESS ACCESS BEEP is
set to ON, the beeper sounds twice
when you unlock the doors by
grabbing the drivers door handle
while carrying the remote.
When you lock the doors by
touching the door lock sensor while
carrying the remote, the beeper
sounds once.
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to CUSTOMIZE
MENU. Press the INFO ( / )
button until you see the above
display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
CONT INUED
K eyless A ccess Beep
Multi-Inf ormation Display
Inst rument s and Cont rols
113
——y
y
(y

y
2010 RL

ÛÝ
To exit KEYLESS ACCESS BEEP
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
keyless access beep setup.
Multi-Inf ormation Display
114
——y
y
(y

y
2010 RL

ÛÝÛ
Ý
ÛÝ
ÛÝ
There are three settings in the
lighting setup:INTERIOR LIGHT
DIMMING TIME
While CUSTOMIZE GROUP is
shown on the multi-inf ormation
display, select LIGHTING SETUP by
pressing the INFO ( / ) button,
then press the SEL/RESET button. AUTO LIGHT SENSITIVITY HEADLIGHT AUTO OFF TIMER
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
CONT INUED
Lighting Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
115
see page 116
seepage118
see page 120
Press the or button.
Press the SEL/RESET button.
——y
y
(y
y
2010 RL

ÛÝ
While LIGHTING SETUP is shown
in the CUSTOMIZE GROUP of the
multi-inf ormation display, press the
SEL/RESET button. You will see the
above display.
Press the SEL/RESET button. The
screen changes as shown above.
Select how long you want the lights
to stay on bef ore they f ade out (60,
30, or 15 seconds) by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
The interior lights f ade out when you
close all doors and the trunk. To
change how long the lights stay on
before they fade out, follow these
instructions:
Int erior L ight Dimming T ime
Multi-Inf ormation Display
116
——y
y
(y

y
2010 RL