key ACURA RL 2011 Owner's Manual

When you turn the ignition switch to
the LOCK (0) position and release it,
or remove the built-in key f rom the
ignition switch, the steering wheel
automatically moves f ully in and up.
Steering wheel movement is also
controlled by the driving position
memory system (see page ).
To change the ‘‘AUTO TILT &
TELESCOPIC’’ setting, see page. If your vehicle’s battery is
disconnected or goes dead, or the
f use f or the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the f use.
The steering wheel returns to its
original position when you push the
ignition switch or insert the built-in
key back in the ignition switch. Push the ignition switch f or more
than 1 second and release it, or
insert the built-in key into the
ignition switch, and remove it. The
steering wheel automatically moves
f ully in and up to let you know the
system is reset.
106 164
Steering Wheel A djustments
Inst rument s and Cont rols
149
10/08/04 19:06:14 31SJA660_154
ProCarManuals.com

These keys contain electronic
circuits that are activated by the
immobilizer system. They will not
work to start the engine if the
circuits are damaged.Protect the keys f rom direct
sunlight, high temperature, and
high humidity.
Donotdropthekeysorsetheavy
objects on them.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
The keys do not contain batteries.
Do not try to take them apart.
The built-in key (see page ) f its
all the locks on your vehicle.
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks. The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on
briefly, then go out. If the indicator
starts to blink, it means the system
does not recognize the coding of the
Honda smart key or built-in key.
Turn the ignition switch to the
LOCK (0) position, release the
ignition switch and push it, or
remove the built-in key, and reinsert
it.ThenturntheswitchtotheON
(II) position again.
181
Keys and Locks, Immobilizer System
Keys and Locks
Immobilizer System
150
KEY NUMBER TAG
BUILT-IN KEYS
10/08/04 19:06:26 31SJA660_155
ProCarManuals.com

The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
chain) is near the ignition switch
when you turn the ignition switch to
the ON (II) position.
If the system repeatedly does not
recognize the coding of your remote
or built-in key, contact your dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle inoperable.
If you have lost your remote or
built-in key and cannot start the
engine, contact your dealer.The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
To use the built-in key, you have to
remove the cover (see page ).
178As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
CONT INUED
Ignition Switch
Immobilizer System, Ignition Switch
Inst rument s and Cont rols
151
IGNITION SWITCH BUILT-IN KEY
COVER
Always take the keyless access remote
and built-in key with you whenever you
leave the vehicle alone.
10/08/04 19:06:40 31SJA660_156
ProCarManuals.com

µµ µ
µ
You can insert or
remove the built-in key only in this
position. To turn the ignition switch
to the LOCK (0) position, the shift
lever must be in Park, and you must
push the knob or built-in key in
slightly.
If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the ignition switch. Firmly
turn the steering wheel to the left or
right as you turn the ignition switch.
You can
operate the audio system and the
accessory power sockets in this
position. When you turn the ignition switch to
the ACCESSORY (I) position, an
‘‘ACCESSORY (I) POSITION’’
message is shown on the multi-
inf ormation display.
This is the normal
ignition switch position when driving.
Several of the indicators on the
instrument panel come on as a test
when you turn the ignition switch
f rom the ACCESSORY (I) to the ON
(II) position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the ignition switch. If you open the driver’s door and
leave the ignition switch in the
ACCESSORY (I) or LOCK (0)
position, you will hear a reminder
beeper, and a message appears on
the multi-information display
according to the ignition switch
position. When the ignition switch is
in the ACCESSORY (I) position, a
‘‘RETURNIGNITIONSWITCHTO
LOCK (0) POSITION’’ message is
shown on the multi-inf ormation
display. When the ignition switch is
in the LOCK (0) position, a
‘‘REMOVE KEY’’ message is shown
on the multi-information display.
TheshiftlevermustbeinPark
bef ore you turn the ignition switch
knob to the LOCK (0) position or
remove the built-in key from the
ignition switch.
Ignition Switch
LOCK (0)
A CCESSORY (I)
ON (II)
ST A RT (III)
152
10/08/04 19:06:49 31SJA660_157
ProCarManuals.com

All doors can be locked f rom the
outsidebyusingthebuilt-inkeyin
the driver’s door. To unlock only the
driver’s door, insert the built-in key,
turn it clockwise, and release it. The
remaining doors unlock when you
turn the built-in key a second time
within a f ew seconds.
Each f ront door has a power door
lock master switch. Either switch
locks and unlocks all doors. Push the
switch down to lock all doors and up
to unlock them. To change the ‘‘DOOR UNLOCK
MODE’’ setting, see page .
When the vehicle speed reaches
about 10 mph (15 km/h) or more, all
the doors lock automatically.When you shif t to P af ter driving, the
driver’s door unlocks.
To change the ‘‘AUTO DOOR
UNLOCK’’ setting, see page .
With the driver’s door open and the
built-in key in the ignition, both
master door lock switches are
disabled. They are not disabled if the
driver’s door is closed. Pushing the
switch down on the open f ront
passenger’s door will lock all doors.
If you try to lock an open driver’s
door by pulling the lock tab rearward
withtheremoteinsidethevehicle
and closing the driver’s door, the
driver’s door will unlock.
To change the ‘‘AUTO DOOR
LOCK’’ setting, see page .
Each door has a lock tab above the
inside door handle. Pull the tab
rearward to lock the door and push it
f orward to unlock. When you pull the
tabrearwardonthedriver’sdoor,all
the doors lock. To lock any door when getting out of
the vehicle, pull the lock tab
rearward and close the door.
109 125
123
L ockout Prevent ion
Door L ocks
Inst rument s and Cont rols
153
POWER DOOR LOCK
MASTER SWITCH
10/08/04 19:07:01 31SJA660_158
ProCarManuals.com

If your vehicle’s battery goes dead or
is disconnected, you can open the
trunk f rom the rear seat by pulling
the trunk release handle. Reach the
handle through the trunk pass-
through.
Keep the trunk lid closed at all times
while driving to avoid damaging the
lid, and to prevent exhaust gas f rom
getting into the interior. Seeon page .
Youcanopenthetrunkinanyof
f our ways: If the doors are locked, press the
trunk release switch on the trunk
lid with the remote in keyless
access operating range.
To close the trunk, press down on
the trunk lid.
Press the trunk release button on
the driver’s door.
Press and hold the trunk release
button on the remote.
If the doors are unlocked, press
thetrunkreleaseswitchonthe
trunk lid. 56Carbon
Monoxide Hazard
Trunk
154
TRUNK RELEASE BUTTON TRUNK RELEASE HANDLE
10/08/04 19:07:13 31SJA660_159
ProCarManuals.com

As a saf ety f eature, your vehicle has
a release lever on the right corner in
the trunk so the trunk can be opened
f rom the inside. To open the trunk,
push the release lever in the
direction indicated by the arrow.
For more inf ormation about child
saf ety, see page .
To protect items in the trunk, you
can disable the trunk-release button
on the driver’s door, the trunk lid,
andtheremote.Todothis,turnoff
the trunk main switch in the glove
box, lock the glove box, and lock the
trunk pass-through cover with the
built-in key.
Parents should decide if their
children should be shown how to use
this feature.The childproof door locks are
designed to prevent children seated
in the rear f rom accidentally opening
the rear doors. Each rear door has a
lock lever near the edge. With the
lever in the LOCK position (lever is
down), the door cannot be opened
f rom the inside regardless of the
position of the lock tab. To open the
door, push the lock tab f orward and
use the outside door handle.
41 Childproof Door L ocks
Emergency T runk Opener
T runk, Childproof Door L ocks
Inst rument s and Cont rols
155
LEVER
TRUNK MAIN SWITCH
lock
unlock
RELEASE LEVER
10/08/04 19:07:24 31SJA660_160
ProCarManuals.com

The rear seat armrest is in the
center of the rear seat. Pivot it down
to use it.To open the cover, pull down the
rear seat armrest. Pull on the tab at
the top of the inner partition, and
press on the button to f ully release
the cover. To close the cover, swing
it up, and push f irmly on the top.
Make sure it latches properly.Make sure all items in the trunk and
those extending through the pass-
through are secured.
For security, this cover can be
locked and unlocked only with the
built-in key. To lock the cover, insert
thekey,andturnitclockwise.
Never drive with this cover open and
the trunk lid open.
See on
page .
A beverage holder is located in the
armrest. 56
Rear Seat Armrest Trunk Pass-through Cover
Carbon Monoxide Hazard
Seats
160
BUTTON
LOCK
INNER PARTITION
10/08/04 19:08:24 31SJA660_165
ProCarManuals.com

To stop the system’s automatic
adjustment, do any of the f ollowing:Press any button on the control
panel: MEMO, 1, or 2.
Push any of the adjustment
switches f or the seat or steering
wheel.
Shif t out of Park.
Adjust the outside mirrors.
If you select a memorized position
without pushing the ignition switch
knob or inserting the built-in key in
the ignition switch, only the seat and
outside mirrors will adjust. To get
the system to also adjust the steering
wheel, push and turn the ignition
switch or insert the built-in key in
the ignition switch. You will hear two
beeps when it is complete. You can use the adjustment switches
to change the positions of the seat,
steering wheel, or outside mirrors
af ter they are in their memorized
position. If you change the
memorized position, the indicator in
the memory button will go out. To
keep this driving position f or later
use, you must store it in the driving
position memory.
Driving Position Memory System
166
10/08/04 19:09:34 31SJA660_171
ProCarManuals.com

Your vehicle has a keyless access
system. When you carry the remote
with you, you can lock/unlock the
door(s), unlock the trunk, and start
the engine without using the built-in
key.
The system may not work if:Thebatteryof theremoteisweak.
You carry a cell phone, a laptop
computer, or other electrical
device near the remote. There is strong electrical current
nearby.
The remote is covered by metal.
A vehicle is being operated with a
transmitter nearby.
When the remote battery is dead. Protect the remote and the built-in
key f rom direct sunlight, high
temperature, and high humidity.
When the vehicle battery is dead.
Make sure the driver always carries
the remote/built-in key set. Do not drop the remote or the
built-in key, and do not set heavy
objects on them.
The built-in keys do not contain
batteries. Keep the remote and the built-in key
away f rom liquids. If they get wet,
dry them immediately with a sof t
cloth.
Always keep the remote and the
built-in key away from any magnetic
material.
Youshouldhavereceivedakey
number tag with your built-in key.
You will need this key number if you
ever have to get a lost key replaced.
UseonlyAcura-approvedkeyblanks.
This key is used to lock/unlock the
doors, glove box, trunk pass-through
cover, and to start the engine (af ter
you remove the ignition switch cover,
see page ). The f ollowing keys come with your
vehicle. Refer to page for how to
separate the keys.
178 181
CONT INUED
K eyless A ccess System
Built -in K ey
Keys
Inst rument s and Cont rols
167
BUILT-IN KEYS KEYLESS ACCESS
REMOTES
KEY NUMBER TAG
10/08/04 19:09:52 31SJA660_172
ProCarManuals.com