open hood ACURA RL 2011 Owners Manual
[x] Cancel search | Manufacturer: ACURA, Model Year: 2011, Model line: RL, Model: ACURA RL 2011Pages: 562, PDF Size: 11.41 MB
Page 176 of 562
Each f ront door has a LOCK/
UNLOCK f eature.
When you touch the door lock
sensor of the f ront door by hand, all
the doors and the trunk will lock.The lock sensors do not operate if :
When you lock the doors, some
exterior lights blink once and the system beeps once. When you
cannot set the security system
because the trunk or hood is open,
no exterior light blinks and/or no
beeper sounds.
Bef ore locking the doors, make sure
theremoteisnotinsidethevehicle. If a remote is within operating range
while you wash your vehicle or when
it is raining heavily, the door sensors
may respond by locking the doors. Within 2 seconds of touching the
handle to lock the doors or locking
the doors with remote, pull the
handletomakesurethedoorsare
actually locked. The door unlock
sensors do not operate f or about 2
seconds af ter the doors are locked. To change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page . To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page
. If you touch the door lock sensor of
the f ront door with your hand
wearing a glove, the door sensor may
delay to respond or not respond by
locking the doors.
Theremoteisnotwithinthe
operating range.
The doors are open.
The ignition switch is not in the
LOCK (0) position.
The built-in key is in the ignition
switch.
The remote is too close to the
vehicle.
Theremotebatteryisdead.
The vehicle battery is dead.
111
113
L ocking the Doors
K eyless A ccess System
170
DOOR LOCK SENSOR
10/08/04 19:10:34 31SJA660_175
ProCarManuals.com
Page 179 of 562
µµ
µ
You cannot lock the doors if any
door is not f ully closed, if the built-in
key is in the ignition switch, or if the
ignition switch is in any position
except the LOCK (0) position.
When you cannot set the security
system because the trunk or hood is
open, no exterior light blinks and/or
no beeper sounds.
Press this button once
to unlock the driver’s door. Press it
twice to unlock the other doors.
Some exterior lights will f lash twice
each time you press the button. The
ceiling light (if the ceiling light
switch is in the DOOR position) will
come on when you press the
UNLOCK button. If you do not open
any door within 30 seconds, the
ceiling light f ades out. If you relock
the doors with the remote before 30
seconds have elapsed, the ceiling
light will go of f immediately. To change the ‘‘DOOR LOCK
MODE’’ setting, see page .
To change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote, but do not open any door
within 30 seconds, the doors
automatically relock and the security
system sets.
To change the ‘‘SECURITY
RELOCK TIMER’’ setting, see page
.
To change the ‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ setting, see
page .
You can also open all power windows
and the moonroof f rom outside the
vehicle with the remote transmitter
(see page ). Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the
built-in key is in the ignition or the
ignition switch is in any position
except the LOCK (0) position. You
cannot open the trunk with the
remote if the trunk main switch is
turned off.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote.
127
116
129
131
187
K eyless A ccess System
UNL OCK TRUNK
PA NIC
Inst rument s and Cont rols
173
10/08/04 19:11:11 31SJA660_178
ProCarManuals.com
Page 321 of 562
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking/side marker
lights, and taillights f lash if someone
attempts to break into your vehicle
or remove the audio unit. This alarm
continues f or 2 minutes, then the
system resets. To reset an activated
system bef ore the 2 minutes have
elapsed, unlock either f ront door
with the remote or the built-in key.Once the security system is set,
opening any door or the hood
without using the built-in key or the
remote will cause it to alarm. It also
alarms if the audio unit is removed
f rom the dashboard or the audio
system wiring is cut.
The security system automatically
sets 15 seconds after you lock the
doors, close the hood, and close the
trunk. For the system to activate,
you must lock the doors f rom the
outside with the remote, built-in key,
lock tab, or master door lock switch.
The security system indicator on the
instrument panel starts blinking
immediately to show you the system
is setting itself .
With the system set, you can still
open the trunk with the remote
without triggering the alarm. The
alarm will sound if the trunk lock is
f orced, or the trunk is opened withthe trunk release button on the
driver’s door or the emergency trunk
opener.
The security system will not set if
the hood, trunk, or any door is not
f ully closed. If the system will not set,
check the Door and Trunk Open
monitor on the instrument panel (see
page ) to see if the doors and
trunk are f ully closed. Since it is not
part of the monitor display, manually
check the hood.
Use the keyless access
remote to quickly check that the
hood, the trunk, and all doors are
closed. Push the lock button twice
within 5 seconds. There should be an
audible conf irmation beep.
Do not attempt to alter this system
or add other devices to it. 13
Security System
Features
315
NOTE:
SECURITY SYSTEM INDICATOR
10/08/04 19:36:08 31SJA660_320
ProCarManuals.com
Page 387 of 562
Bef ore you begin driving your
vehicle, you should know what
gasoline to use and how to check the
levels of important f luids. You also
need to know how to properly store
luggage or packages. The
inf ormation in this section will help
you. If you plan to add any
accessories to your vehicle, please
read the information in this section
first..............................
Break-in Period . 382
.................
Fuel Recommendation . 382
.........
Service Station Procedures . 383
....................................
Ref ueling . 383
.....
Tighten Fuel Cap Message . 385
Opening and Closing
................................
the Hood . 385
...................................
Oil Check . 387
.............
Engine Coolant Check . 387
...............................
Fuel Economy . 388
...
Accessories and Modif ications . 391
.............................
Carrying Cargo . 393
Bef ore Driving
Bef ore Driving
381
10/08/04 19:49:02 31SJA660_386
ProCarManuals.com
Page 391 of 562
Park the vehicle, and set the
parking brake. Pull the hood
release lever located under the
lower lef t corner of the dashboard.
The hood will pop up slightly.
Your vehicle’s on board diagnostic
system will detect a loose or missing
f uel f ill cap as an evaporative system
leak. The f irst time a leak is detected
a ‘‘TIGHTEN FUEL CAP’’ message
appears on the multi-inf ormation
display. Turn the engine of f , and
conf irm the f uel f ill cap is installed. If
it is, loosen it, then retighten it until
it clicks at least once. The message
should go of f af ter several days of
normal driving once you tighten or replace the f uel f ill cap. To scroll to
another message, press the INFO
button. The ‘‘TIGHTEN FUEL CAP’’
message will appear each time you
restart the engine until the system
turns the message of f .
If the system still detects a leak in
the vehicle’s evaporative emissions
system, the malf unction indicator
lamp (MIL) comes on. If the f uel f ill
cap was not already tightened, turn
the engine of f , and check or
retighten the f uel f ill cap until it
clicks at least once. The MIL should
go off after several days of normal
driving once the cap is tightened or
replaced. If the MIL does not go of f ,
have your vehicle inspected by a
dealer. For more inf ormation, see
page .
1.
509
CONT INUED
Opening and Closing the Hood
Tighten Fuel Cap Message
Service Station Procedures
Bef ore Driving
385
HOOD RELEASE LEVER
10/08/04 19:49:43 31SJA660_390
ProCarManuals.com
Page 392 of 562
If the hood latch handle moves
stif f ly, or if you can open the hood
without lifting the handle, the
mechanism should be cleaned and
lubricated. Reach between the hood and the
f ront bumper with your f inger.
Slide the latch handle up.To close the hood, lower the hood to
about a f oot (30 cm) above the
f ender, then f irmly press down on
the f ront edge of the hood. Make
sure it is securely latched.
Lif t the hood up most of the way.
The hydraulic supports will lif t it
uptherestof thewayandholdit
up.
2. 3.
Service Station Procedures
386
LATCH
10/09/08 21:18:42 31SJA660_391
ProCarManuals.com
Page 465 of 562
Your vehicle does not require any oil
additives. Additives may adversely
af f ect the engine or transmission
perf ormance and durability.Open the hood, and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.
Run the engine until it reaches
normal operating temperature,
then shut it off.
Always change the oil and f ilter
according to the maintenance
messages shown on the multi-
inf ormation display. The oil and f ilter
collect contaminants that can
damage your engine if they are not
removed regularly.
You may use a synthetic motor oil if
it meets the same requirements
given f or a conventional motor oil: it
displays the API Certif ication Seal
and it is the proper weight. You must
f ollow the oil and f ilter change
intervals shown on the multi-
inf ormation display.
Changing the oil and f ilter requires
special tools and access f rom
underneath the vehicle. The vehicle
should be raised on a service station-
type hydraulic lif t f or this service.
Unless you have the knowledge and
proper equipment, you should have
this maintenance done by a skilled
technician.
1.2.
CONT INUED
Synthetic Oil
Engine Oil A dditivesChanging the Engine Oil and
Filter
A dding Engine Oil, Changing the Engine Oil and Filter
Maint enance
459
OIL DRAIN BOLT WASHER
10/08/04 20:02:11 31SJA660_464
ProCarManuals.com
Page 475 of 562
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ). Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ). Open the hood. Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the engine compartment
side cover.
Reinstall the battery cover. (Driver’s side)
2.
3.
1.
4.5.
6.
7.
8.
9.
457
492
Lights
Maint enance
469
BULB
CONNECTOR
10/08/04 20:04:00 31SJA660_474
ProCarManuals.com
Page 476 of 562
Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Open the hood.
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ).
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Reinstall the engine compartment
side cover.
(Driver’s side)
Reinstall the battery cover.
2. 1.
3.
4.5.
6.
7.
457
492 8.
9.
Lights
Replacing a Front T urn Signal
Light Bulb
470
BULB SOCKET
10/08/04 20:04:13 31SJA660_475
ProCarManuals.com
Page 477 of 562
Remove the left or right side
engine compartment cover (see
page ).
Use a f lat-tip screwdriver to
remove the holding clip f rom the
windshield washer reservoir. (Passenger’s side) Open the hood.
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ).Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Turn on the lights to make sure
the new bulb is working.
Reinstall the engine compartment
side cover. Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Reinstall the windshield washer
reservoir.
(Driver’s side)
Reinstall the battery cover. (Passenger’s side)
1.
2.
3.
4.
5.6.
7.
8.
9.
457
492
10.
Lights
Replacing a Front Parking/Side
Marker Bulb
Maint enance
471
SOCKET
BULB
CLIP
10/08/04 20:04:31 31SJA660_476
ProCarManuals.com