ACURA RL 2012 Owners Manual

When the speed is set, it is shown
along with a vehicle icon and
distance bars on the multi-
inf ormation display.
Refertopage forhowtosetand
change the set distance between
your vehicle and the vehicle ahead of
you.If you change the speed unit
measurement f rom the f actory
def ault setting, the initial speed unit
measurement is shown under the
current unit. To change the speed unit
measurement f rom mph to km/h,
see page .
32892
A daptive Cruise Control (A CC)
Features
325
SET VEHICLE
SPEED U.S.
U.S.
SET VEHICLE
DISTANCEINITIAL SPEEDUNIT
Canada
Canada
11/07/20 18:42:01 31SJA670_330
ProCarManuals.com

The set speed can be increased by
using the RES/ACCEL button or the
accelerator pedal.To increase the set speed with the
RES/ACCEL button, do this:
Press and hold the RES/ACCEL
button. The vehicle will accelerate.
When you reach the speed you want,
release the button.
To increase your speed in small
amounts, tap the RES/ACCEL
button repeatedly. Each time you do
this, your vehicle will speed up about
1 mph (1 km/h).
While the vehicle accelerates to the
set speed, the set speed on the multi-
inf ormation display will f lash.
If a vehicle ahead of you is driving at
a slower speed than the speed you
want to set, your vehicle will not
accelerate; it will keep some distance
between your vehicles.To increase the set speed with the
accelerator pedal, do this:
Press the accelerator pedal to
increase to the speed you want, then
press the SET/DECEL button. The
set speed will be shown on the multi-
inf ormation display. If you do not
press the SET/DECEL button, your
vehicle will return to the previously
set speed.
The ACC beeper will not sound
while you press the accelerator pedal,
no matter how close you get to the
vehicle ahead of you. Increasing the Set Speed
A daptive Cruise Control (A CC)
326
RES/ACCEL BUTTON
11/07/20 18:42:10 31SJA670_331
ProCarManuals.com

The set speed can be decreased
using the SET/DECEL button or the
brake pedal.
To decrease the set speed with the
SET/DECEL button, do this:
Press and hold the SET/DECEL
button. Release the button when you
reach the speed you want.
To slow down in small amounts, tap
the SET/DECEL button repeatedly.Each time you do this, your vehicle
slows down about 1 mph (1 km/h).
When the system detects a vehicle
ahead of you, a beeper sounds once
and a solid-line vehicle icon appears
on the multi-information display. The set cruising speed will be shown
on the multi-information display.
On a steep downhill, the vehicle
speed may exceed the set cruising
speed.
To decrease the set speed with the
brake pedal, do this:
Tap the brake pedal. When the
vehicle slows down to the speed you
want, press the SET/DECEL button.
The set speed will be shown on the
multi-inf ormation display. If you use
the brake pedal to decrease speed,
andthenpresstheRES/ACCEL
button, your vehicle will return to the
previously set speed.
CONT INUED
Decreasing the Set Speed Detecting a Vehicle A head of You
A daptive Cruise Control (A CC)
Features
327
SET/DECEL BUTTONU.S.
Canada
11/07/20 18:42:20 31SJA670_332
ProCarManuals.com

With ACC on, the distance between
your vehicle and the vehicle ahead of
you is controlled and maintained.
You can change this distance to one
of three ranges: long, middle, or
short.To change the range, press the
DISTANCE button. Each time you
press the button, the range changes
f rom Long, to Middle, and then to
Short.
The higher your vehicle speed is, the
longer the distance between the
vehicle in f ront will be set as shown
below.
When that vehicle changes lanes or
goes out of ACC range, a beeper
sounds once. If there is no vehicle
ahead of you within ACC range, a
dotted-line vehicle icon will be on the
multi-inf ormation display.
To set the ACC beeper on or of f , see
page .90
50 mph
(80 km/h)
154 feet
47 meters
111 feet
34 meters
85 feet
26 meters Speed
Vehicle
Distance
Long
Middle
Short65 mph
(104 km/h)
200 feet
61 meters
138 feet
42 meters
101 feet
31 meters
Changing Vehicle Distance
A daptive Cruise Control (A CC)
328
DISTANCE BUTTON U.S.
Canada
11/07/20 18:42:30 31SJA670_333
ProCarManuals.com

Press the ACC button. The ACC
indicator in the instrument panel
goes off. Tap the brake pedal. Push the CANCEL button on the
steering wheel.If you cancel ACC by pressing the
ACC button, the previously set
cruising speed is erased f rom
memory. The distance you select is also
shown on the multi-inf ormation
display.
ACC is canceled whenever you do
any of these actions:When you push the CANCEL button
or tap the brake pedal to cancel ACC,
the set cruising speed stays in
memory. When you turn on ACC
again, the speed is shown on the
multi-inf ormation display. To return
to that speed, accelerate to over 25
mph (40 km/h), then press the RES/
ACCEL button. Canceling the A CC
A daptive Cruise Control (A CC)
Features
329
LONG
RANGE
MIDDLE
RANGE
SHORT
RANGECANCEL BUTTON U.S.
U.S.
U.S. Canada
Canada
Canada
11/07/20 18:42:40 31SJA670_334
ProCarManuals.com

This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. If it comes on at any other
time, there is a problem in the ACC
system. If this happens, take the
vehicle to your dealer to have it
checked. The vehicle speed decreases
below22mph(35km/h).Driving on a mountainous road, or
driving of f road f or extended
periods.
When the ABS or VSA is activated. Abrupt steering wheel movement.
Poor weather (rain, f og, snow, etc.)
When the radar sensor in the front
grille gets dirty.
The vehicle ahead of you cannot
be detected.
An abnormal tire condition is
detected, or the tires are skidding. When ACC is automatically canceled,
the beeper sounds about 1 second,
and an ACC OFF message appears
on the multi-inf ormation display f or 3
seconds.
Any of these conditions may cause
ACC to cancel:
The ACC system cannot be used
while this indicator (amber) is on. When the VSA system indicator
comes on.
If you turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position af ter ACC was automatically
canceled, the set speed is erased,
and you must enter it again (see
page ). If ACC is canceled by any these
conditions, wait until the condition
improves, then press the RES/
ACCEL button to restore ACC.
When you do this, the vehicle will
resume its set cruising speed.
324 A utomatic A CC Cancelation A CC Indicator
A daptive Cruise Control (A CC)
330
ACC INDICATOR
11/07/20 18:42:51 31SJA670_335
ProCarManuals.com

The multi-inf ormation display shows
various messages related to ACC.
For a description of each ACC
message you may see, ref er to the
chart on this and the f ollowing page.
Message
CONT INUED
Description
ACC is on.
ACC detects a vehicle ahead of you.
You will hear a beep when the vehicle
moves out of the ACC radar sensor’s
range.
ACC does not detect a vehicle ahead
of you.
You will hear a beep when ACC
detects a vehicle ahead of you.
Messages on the
Multi-Inf ormation Display
A daptive Cruise Control (A CC)
Features
331
U.S.
U.S. Canada
Canada
11/07/20 18:43:00 31SJA670_336
ProCarManuals.com

Message Message DescriptionDescription
Apply the brakes immediately.
Your vehicle is too close to the vehicle
ahead of it.
You will hear a continuous beep.
ACC needs to be checked.
Have your vehicle checked by a
dealer. ACC has automatically canceled
because its radar sensor in the f ront
grill is dirty.
You will hear a beep for about 1
second.
ACC has automatically canceled
because of bad weather or other
conditions.
You will hear a beep for about 1
second.
A daptive Cruise Control (A CC)
332
11/07/20 18:43:06 31SJA670_337
ProCarManuals.com

To switch f rom ACC to cruise
control, press the distance button on
the steering wheel, and hold it f or 1
second.
Always be aware which mode is
selected. When the cruise control is selected,
ACC does not sound a beeper or
display a message on the multi-
inf ormation display. Make sure to
keepasafedistancefromthevehicle
ahead of you. When you press the button, you will
see CRUISE MODE SELECTED on
the multi-information display for 2
seconds.ToswitchbacktoACC,
press and hold the distance button
again for 1 second. Switching to Cruise Control
A daptive Cruise Control (A CC)
Features
333
DISTANCE BUTTON
Press the distance button.
11/07/20 18:43:14 31SJA670_338
ProCarManuals.com

·
µ
µ The HomeLink
Universal
Transceiver built into your vehicle
canbeprogrammedtooperateupto
three remote controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
Bef ore programming your
HomeLink to operate a garage door
opener, conf irm that the opener has
an external entrapment protection
system, such as an ‘‘electronic eye,’’
or other saf ety and reverse stop
f eatures.
If your garage door was
manuf actured bef ore April 1, 1982,
you may not be able to program
HomeLink to operate it. These units
do not have safety features that
cause the motor to stop and reverse
it if an obstacle is detected during
closing, increasing the risk of injury.
Do not use HomeLink with anygarage door opener that lacks saf ety
stop and reverse f eatures.
Units manuf actured between April 1,
1982 and January 1, 1993 may be
equipped with saf ety stop and
reverse f eatures. If your unit does
not have an external entrapment
protection system, an easy test to
conf irm the f unction and
perf ormance of the saf ety stop and
reverse f eature is to lay a 2 4
under the closing door. The door
should stop and reverse upon
contacting the piece of wood.
As an additional safety feature,
garage door openers manuf actured
af ter January 1, 1993 are required to
have external entrapment protection
systems, such as an electronic eye,
which detect an object obstructing
the door.
Refer to the safety information that
came with your garage door openerto test that the safety features are
f unctioning properly. If you do not
have this information, contact the
manuf acturer of the equipment.
Bef ore programming HomeLink to a
garage door or gate opener, make
sure that people and objects are out
of the way of the device to prevent
potential injury or damage.
When programming a garage door
opener, park just outside the garage.
If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 10 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1. General Saf ety Inf ormation
Important Saf ety PrecautionsT raining HomeL ink
HomeL inkUniversal T ransceiver
Bef ore you begin
334
11/07/20 18:43:23 31SJA670_339
ProCarManuals.com