door lock ACURA RL 2012 Service Manual

µµ
µ You cannot lock the doors if any
door is not f ully closed, if the built-in
key is in the ignition switch, or if the
ignition switch is in any position
except the LOCK (0) position.
When you cannot set the security
system because the trunk or hood is
open, no exterior light blinks and/or
no beeper sounds.
Press this button once
to unlock the driver’s door. Press it
twice to unlock the other doors.
Some exterior lights will f lash twice
each time you press the button. The
ceiling light (if the ceiling light
switch is in the DOOR position) will
come on when you press the
UNLOCK button. If you do not open
any door within 30 seconds, the
ceiling light f ades out. If you relock
the doors with the remote before 30
seconds have elapsed, the ceiling
light will go of f immediately.To change the ‘‘DOOR LOCK
MODE’’ setting, see page .
To change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote, but do not open any door
within 30 seconds, the doors
automatically relock and the security
system sets.
To change the ‘‘SECURITY
RELOCK TIMER’’ setting, see page
.
To change the ‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ setting, see
page .
You can also open all power windows
and the moonroof f rom outside the
vehicle with the remote transmitter
(see page ).Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the
built-in key is in the ignition or the
ignition switch is in any position
except the LOCK (0) position. You
cannot open the trunk with the
remote if the trunk main switch is
turned off.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote. 127
116
129 131
188
K eyless A ccess System
UNL OCKTRUNK
PA NIC
Inst rument s and Cont rols
173
11/07/20 18:22:11 31SJA670_178
ProCarManuals.com

The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof eachremote.
Make sure you store your desired
driving position in the memory thatis activated by the remote you
normally carry.
When you unlock the driver’s door
with your remote transmitter, each
remote transmitter activates the
customized settings related to that
remote.To turn of f this f eature, press and
hold the LOCK and UNLOCK
buttonsatthesametime.TheLED
in the remote will blink once. Then
release the buttons. Doing this
cancels the keyless memory settings
f or that remote and restores the
def ault settings.
Some of them keep the same
settings as they were set previously.
To turn the keyless memory settings
back on, repeat this procedure. The
LED will blink twice to indicate the
f eature has been turned on.
When you unlock and open the
driver’s door with the remote, the
driver’s seat (except power lumbar)
and outside mirrors move to the
positions stored in memory. An
indicator on one of the driving
position memory buttons on the
driver’s door also comes on. Navigation system pref erences
(see the navigation system
manual). Here are the settings activated with
the remote:
Driving position memory
(see page ).
Customized settings
(see page ).
Audio system settings
(see page ).
Climate control settings
(see page ).
Compass system pref erences
(see page ).164
81
213
205
281
U.S. RL model
Except U.S. RL model
K eyless A ccess System
Recalling a Memorized Driving
Position
174
DRIVER’S ID
11/07/20 18:22:22 31SJA670_179
ProCarManuals.com

To remove the ignition switch cover,
insert the built-in key (see page ),
then pull the cover out by pulling the
built-in key while pushing it. Also, if you close the door when the
ignition switch is not in the LOCK
(0) position and the remote is not
inside the vehicle, the keyless access
alarm sounds outside the vehicle, a
message appears on the multi-
inf ormation display, and the beeper
sounds if the ignition switch is in the
ON (II) position.
When the beeper sounds af ter you
close the driver’s door outside the
vehicle, check the position of the
ignition switch and the location of
the remote.
If the engine is running and you
removetheremotefromthevehicle,
it will continue to run. But once
turned to the LOCK (0) position, the
engine will not restart until a remote
is brought back into the vehicle. To turn the ignition switch to the
LOCK (0) position, put the
transmission in Park, press the
switch in, and turn it to the LOCK
(0) position. When the transmission
is not in Park, you cannot turn the
ignition switch to the LOCK (0)
position.
Bef ore leaving the vehicle, make
sure the ignition switch is in the
LOCK (0) position.
If you open the driver’s door with the
ignition switch in the ACCESSORY
(I) position, a beeper will sound.
You will also see a ‘‘RETURN
IGNITION SWITCH TO LOCK (0)
POSITION’’ message on the multi-
inf ormation display.181
K eyless A ccess System
Removing the Ignition Switch
Cover
178
BUILT-IN KEY IGNITION SWITCH COVER
pushpull
11/07/20 18:22:55 31SJA670_183
ProCarManuals.com

The engine does not restart if you
turn the ignition switch to the LOCK
(0) position when the remote is
outside the vehicle. Check where the
remote is. Make sure that you carry
the remote or built-in key with you
when you operate the ignition switch.
If you pass the remote through an
open window, the system does not
respond.Also,evenwhentheremote
is inside the vehicle, the beeper may
sound when the location of the
remote is not detected due to
surrounding conditions. It is not a
f ailure. Make sure that you carry the
remote with you. The outside beeper sounds when
the ignition switch is in the
ACCESSORY (I) or the ON (II)
position.
When the ignition switch is in the
ON (II) position, the multi-
inf ormation display shows
‘‘KEYLESS REMOTE NOT
DETECTED,’’ and the inside and
outside beepers sound.
The multi-inf ormation display
message goes away when you
bring the remote back inside the
vehicle, and close the door or
apply the parking brake.
If the engine is running and you
removetheremotefromthe
vehicle, it will continue to run.
Once turned to the LOCK (0)
position, the engine will not restart
until a remote is brought back into
the vehicle. When you are pressing the ignition
switch, or when the ignition switch is
in the ON (II) position, the beeper
sounds if you take the remote out of
the vehicle and close the door.
CONT INUED
K eyless A ccess System
K eyless Remot e Not Det ect ed
Beeper and Message
Inst rument s and Cont rols
179
11/07/20 18:23:04 31SJA670_184
ProCarManuals.com

The keyless access system
indicator comes on and stays on
while you are driving.
The indicator comes on and stays
on with the ignition switch in the
ON (II) position.
The multi-inf ormation display
shows ‘‘CHECK KEYLESS
ACCESS SYSTEM.’’
In this case, use the built-in key to
lock/unlock the doors and start the
engine. The indicator comes on f or several
seconds when you turn the ignition
switch to the ON (II) position. Have
your vehicle checked by your dealer
if : Thebatteriesintheremotenormally
last about 2 years. To ensure
maximum battery life, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-inf ormation display shows
‘‘KEYLESS REMOTE LOW
BATTERY,’’ replace the batteries as
soon as possible (see page ).175Check K eyless A ccess Syst em K eyless Remot e L ow Bat t ery
K eyless A ccess System
180
KEYLESS ACCESS SYSTEM
INDICATOR
11/07/20 18:23:12 31SJA670_185
ProCarManuals.com

You can open and close the windows
and moonroof with the built-in key in
the driver’s door lock.
To open:
Insert the built-in key in the driver’s
door lock.
Turn the key clockwise, then
release it. Press the UNLOCK button a
second time, and hold it. All the
doors unlock, and all f our windows
and moonroof start to open. To
stop the windows and moonroof ,
release the button.
To open the windows and
moonroof f urther, press the
button again (within 10 seconds of
step 1) and hold it. If the windows
and the moonroof stop bef ore the
desired position, repeat steps 1
and 2.
You cannot close the windows or the
moonroof with the remote. You can open all of the windows and
the moonroof f rom outside with the
remote.
Press the UNLOCK button once
to unlock the driver’s door.
1.
2. 2.
3.
1.
Power Windows
Opening/Closing the Windows
and Moonroof with the Built-in
Key Opening the Windows and
Moonroof with the Remote
188
Open
Close UNLOCK BUTTON
11/07/20 18:24:15 31SJA670_193
ProCarManuals.com

CONT INUED
Turn the ignition switch to the ON
(II) position bef ore operating the
moonroof switch on the ceiling
console. To open the moonroof , pull
back the moonroof switch. To close
the moonroof , push the moonroof
switch f orward. Release the switch
to stop the moonroof . To close the windows and the
moonroof f urther, turn and hold
the key again (within 10 seconds
of step 2).
If the windows and the
moonroof stop bef ore the desired
position, repeat steps 2 and 3. Turn the built-in key clockwise
again, and hold it. All four
windows and the moonroof start to
open. To stop the windows and
moonroof , release the built-in key.
To open the windows and the
moonroof f urther, turn and hold
the key again (within 10 seconds
of step 2).
To close:
Insert the built-in key in the driver’s
door lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again, and hold it. All four
windows and the moonroof start to
close. To stop the windows and
the moonroof , release the key.4.
4. 3.
1.
2.
3.
Power Windows, Moonroof
Opening/Closing the Moonroof
with the Ceiling Console Switch
Inst rument s and Cont rols
189
NOTE:
MOONROOF SWITCH
Open
CloseTilt
11/07/20 18:24:25 31SJA670_194
ProCarManuals.com

Af ter pushing the DOOR button, all
the lights come on when you open
any door, unlock the doors with the
remote or built-in key, or turn the
ignition switch f rom the ON (II) or
the ACCESSORY (I) position to the
LOCK (0) position. The indicator in
the button comes on as a reminder.
The f ront and rear of the ceiling
have ceiling lights.
To change the ‘‘INTERIOR LIGHT
DIMMING TIME’’ setting, see page
. Push each ceiling light button to turn
its light on and of f .
Push the ON button to turn on all the
ceiling lights. Push the OFF button
to turn them off. 116 Ceiling L ights
Interior Lights
200
CEILING LIGHT
BUTTONS
CEILING LIGHT
BUTTONS OFF BUTTON
DOOR BUTTON
ON BUTTONFront
Rear
11/07/20 18:25:41 31SJA670_205
ProCarManuals.com

Ý Û Many climate control f unctions can
still be controlled by standard
buttons, dials, and knobs, but some
f unctions can only be accessed using
the interf ace dial. The interf ace dial
has two parts, a knob and a selector.
The knob turns lef t and right. Use it
to make selections or adjustments to
a list or menu on the screen.To select an item that comes with
, , , or icons,
push the interf ace selector up, down,
lef t, or right.When you unlock the doors with
your remote, the driver’s ID (Driver
1orDriver2)isdetected,andthe
climate control settings are turned to
therespectivemodeautomatically
when the ignition is turned to the
ON (II) position.
The climate control system can also
be operated by voice control.
See the navigation system manual
f or complete details.
Ref er to Voice Control Basics f or
complete details (see page ). When you make a selection, press
ENTERtogotothatselection.
304
On models with navigation system
On models without navigation system
Interf ace Dial Personalization Setting
Voice Control System
Climat e Cont rol Syst em
Features
205
ENTER
SELECTOR KNOB
11/07/20 18:26:12 31SJA670_210
ProCarManuals.com

Most audio system f unctions can still
be controlled by standard buttons,
dials, and knobs, but some f unctions
can only be accessed using the
interf ace dial. The interf ace dial has
two parts, a knob and a selector.The selector can be pushed lef t,
right, up, down, and in. Use the
selector to scroll through lists, to
select menus, and to highlight menu
items. When you make a selection,
press ENTER to go to that selection. The knob turns lef t and right. Use it
to make selections or adjustments to
a list or menu on the screen.When you unlock the doors with
your remote and turn the audio
system on, the driver’s ID (Driver 1
or Driver 2) is detected, and the
radio preset memory (see page ),
the auto select preset memory (see
page ), and the volume and
sound level settings (see page )
are turned to the respective
memorized mode automatically.
The audio system can also be
operated by voice control.
See the navigation system manual
f or complete details.
Ref er to Voice Control Basics f or
complete details (see page ).226 217
304217
On models with navigation system
On models without navigation system
Interf ace Dial Personalization Setting
Voice Control System
Audio System
Features
213
KNOB
ENTER
SELECTOR
11/07/20 18:27:31 31SJA670_218
ProCarManuals.com