seat adjustment ACURA RL KA9 1996 Service Repair Manual

Navigation System

System Diagnosis Mode (cont'd)

GPS Offset Time

This screen is for factory use only. It allows adjustment

of the GPS time. This display updates in real time.

• "GPS Time" is the time as received from the GPS

satellites. It is in Greenwich Mean Time (GMT).

• "System Time" is the internal time used by the navi-

gation unit to calculate your position on the map.

It is also in Greenwich Mean Time (GMT).

• "Display Time" is the time shown on Setup screen 2

"Adjust Time Zone/Clock", and reflects any changes

due to daylight savings time or time adjustments

entered by the customer.

• Date, Hour, Minute, and "Set" buttons should not be

used.
Mic Level

This diagnostic allows you to independently test the

microphone and the TALK and BACK buttons on the

steering wheel (voice control switch). The microphone

and voice control switch are used to activate the voice

control system. The microphone is located near the map

light in the ceiling. It is directional, and works best if the

voice is coming from the drivers seat.

• Press the TALK button on the steering wheel, and in a

normal voice say "testing". The TALK indicator on

the screen should momentarily become green, and

the text "Now Recording..." should appear in yellow.

In addition, the Mic Level indicator should move at

least to the 6th bar. If the Talk indicator on the screen

does not briefly become green, then check the wiring

from the steering wheel talk button to the navigation

unit. If there is no "Mic Level" movement when you

speak, then you should check the wire running from

the microphone to the control unit.

• Press the BACK button on the steering wheel. This

should cause the Cancel indicator on the screen to

momentarily become green. If it does not briefly

change to green, then check the wiring from the

steering wheel BACK button to the navigation unit.ProCarManuals.com

Shift Leve r
Link Adjustmen t (cont'd)
7. Chec k tha t th e hol e i n th e lin k adjuste r i s perfectl y
aligned wit h th e hol e i n th e lin k rod .
LINK ADJUSTE R
Lin k adjuste r
Too Shor tLink adjuste rToo Lon gExac tAlignmen t
NOTE: Ther e ar e tw o hole s i n th e lin k adjuster . The y
ar e positione d 90 ° apar t t o allo w lin k adjustment s i n
1/ 4 tur n increments .
8 I f no t perfectl y aligned , loose n th e locknu t o n th e
lin k adjuster , an d adjus t a s required .
9. Tighte n th e locknut .
TORQUE : 7 N- m (0. 7 kgf-m , 5 Ibf-ft)
10. Instal l th e loc k pi n o n th e adjuster . I f yo u fee l th e
loc k pi n bindin g a s yo u reinstal l it , th e lin k ro d i s
stil l ou t o f adjustmen t an d mus t b e readjusted .
11. Mak e sur e th e loc k pi n i s seate d securel y i n th e
adjuster .
NOTE : Replac e th e loc k pi n i f i t doe s no t sna p ove r
th e lin k adjuste r securely .
12. Mov e th e shif t leve r t o eac h gear , an d verif y tha t th e
A/T gea r positio n indicato r follow s th e transmissio n
rang e switch .
13 . Star t th e engine , an d chec k th e shif t leve r i n al l
gears . I f an y gea r doe s no t wor k properly , refe r t o
troubleshootin g o n pag e 14-10 0 thru 14-103 .
14. Instal l th e cente r consol e (se e sectio n 20 ).
15 . Inser t th e ignitio n ke y int o th e ke y cylinde r o n th e
A/T gea r positio n indicato r panel , an d verif y tha t th e
shif t loc k leve r i s released .
LINK RO D
ProCarManuals.com

GLASSRemoval , pag e 20- 7
Adjustment , pag e
20-16
REA R LOWE RCHANNE L
STRIKERAdjustment , pag e20-18
GLAS S RU N
CHANNE L
FRON T
CHANNE L
OUTERHANDL E
COVE R
OUTE R HANDL E
Removal , pag e
20-5
POWE R DOO R
LOC K SWITC H
LATCHRemoval , pag e20-5
REGULATO RRemoval, pag e 20- 7
CYLINDE RSWITCH OUTE
R HANDL E
BASE
SEAT B
SEAT A
LOC K CYLINDE R
INNER HANDL ECABLE
INNER
HANDL E
TRI M PLAT E
LATCHPROTECTO R
ProCarManuals.com

Adjustment ('9 6 - 9 8 models )
Before adjustin g th e headlights :
• Par k th e vehicl e o n leve l ground .
• Mak e sur e th e fue l tan k i s full .
• Th e drive r o r someon e who weigh s th e sam e shoul d
si t i n th e driver' s seat .
• Loa d th e trun k wit h th e item s yo u usuall y carry .
• Pus h dow n o n th e fron t an d rea r bumper s severa l
time s t o mak e sur e th e vehicl e i s sittin g normally .
CAUTION : Haloge n headlight s becom e ver y ho t i n use ;
d o no t touc h the m o r th e attachin g hardwar e immedi -
atel y afte r the y hav e bee n turne d off .
1 . Ope n th e hood .
2 . Chec k th e horizonta l adjustmen t indicator .
Th e mar k o n th e horizonta l indicato r gea r shoul d b e
aligne d wit h th e mar k o n th e horizonta l indicator .
NOTE : Th e illustratio n show s th e lef t sid e adjuster .
HORIZONTA L INDICATO RGEARARRO W
MARK
3. Chec k th e vertica l adjustmen t indicator . Th e bubbl e
shoul d b e centere d underneat h th e longes t scrib e
mar k o n th e gauge .
4 . I f eithe r indicato r i s no t aligne d wit h it s "O " mar k a s
describe d above , a n adjustmen t ca n b e mad e b y
usin g a Phillip s screwdriver .
VERTICAL INDICATOR :
INDICATOR (Bubble )
5. Adjus t th e headlight s t o loca l requirement s b y turn -
ing th e adjusters .
6. Afte r headligh t replacement , i t ma y b e necessar y t o
readjus t th e horizonta l indicator gear.
• Firs t instal l th e headlight , an d adjus t it s horizonta l
an d vertica l aiming s accordin g t o loca l require -
ments .
• The n chec k tha t th e arro w o n th e horizonta l indi -
cato r gea r i s aligne d wit h th e mar k o n th e hori -
zonta l indicator .
• I f the y ar e no t aligned , remov e th e screw , adjus t
th e indicato r gear , an d retighte n th e screw .
NOTE : A s th e oute r lense s ar e mad e o f a n acryli -
coated , polycarbonate d material , d o no t cove r th e
headlight s whe n the y ar e turne d on .
MAR K
ARRO W
SCREW
HORIZONTA L
I NDICATO R
GEA R
ProCarManuals.com

Headlights
Adjustmen t ('9 9 - 0 4 models )
CAUTION : Headlight s becom e ver y ho t i n use ; d o no t
touc h the m o r an y attachin g hardwar e immediatel y
afte r the y hav e bee n turne d off .
Befor e adjustin g th e headlights :
• Par k th e vehicl e o n a leve l surface .
• Mak e sur e th e tir e pressure s ar e correct .
• Th e drive r o r someon e who weigh s th e sam e shoul d
si t i n th e driver' s seat .
1 . Clea n th e oute r len s s o tha t yo u can see th e cente r
o f th e headlights . 4
. Tur n th e lo w beam s on .
5 . Determin e if th e headlight s ar e aime d properly .
Vertica l adjustment :
Measur e th e heigh t o f th e headlight s (A) . Th e light s
shoul d reflec t 5 2 m m (2. 1 in. ) belo w (B ) th e head -
light height .
Horizonta l adjustment : ('9 9 - 0 0 models )
Th e widt h o f th e refractin g point s (C ) shoul d b e th e
sam e a s th e widt h o f th e headligh t centra l point s (D ,
E).
2. Par k th e vehicl e in fron t o f a wal l o r a screen .
CENTER
SCREE N
3. Ope n th e hood .
7.5 m (2 5 ft )
6. I f necessary , adjus t th e headlight s t o loca l require -
ment s b y turnin g th e horizonta l adjuste r an d th e
vertica l adjuster .VERTICA LADJUSTE R
HORIZONTA L
ADJUSTE R ('9 9 - 0 0 models )
ProCarManuals.com

Driving Positio n Memor y Syste m (DPMS )
Descriptio n
The driver' s seat , th e powe r mirror s an d th e steerin g column , whos e position s ar e determine d th e driver' s position , hav e
a memor y feature . Th e sea t adjustments , th e mirro r adjustments , an d th e steerin g colum n adjustment s can be regulate d
separately . Al l o f adjustment s ca n b e memorize d b y th e pressin g th e MEM O butto n o n th e drivin g positio n memor y
switch , an d the n pressin g on e o f th e tw o positio n button s withi n 5 seconds . Pressin g th e appropriat e positio n butto n wil l
mov e th e seat , th e mirro r an d th e steerin g colum n t o th e positio n memorize d fo r drive r 1 o r drive r 2 , eliminatin g manua l
adjustment s whe n changin g drivers .
NOTE : Disconnectin g th e batter y wil l cance l th e memorize d positions .
STEERIN G COLUM N POSITIO N SENSOR S
B y mean s o f th e variabl e resistor-typ e til t positio n senso r an d extend-retrac t positio n sensor , th e steerin g colum n contro l
uni t detect s th e voltag e change s cause d b y th e movement s o f th e steerin g column . Thes e voltag e change s ar e store d in
memory , an d th e steerin g colum n positio n is memorized .
POWE R SEA T POSITIO N SENSOR S
Eac h moto r ha s a ree d switc h senso r whic h detect s moto r rotatio n an d send s a puls e to th e powe r sea t contro l uni t whe n
th e moto r rotates . Th e contro l uni t store s th e numbe r o f pulse s i n it s memory , an d th e sea t positio n is memorized .
POWE R MIRRO R POSITIO N SENSOR S
B y mean s o f a Hall-effec t typ e til t positio n senso r an d swin g positio n sensor , th e powe r mirro r contro l uni t detect s th e
voltag e change s cause d b y th e movement s o f th e mirrors .
Thes e voltag e change s ar e store d in memory , an d th e powe r mirro r position s ar e memorized .
"AUTO " SWITC H FUNCTIO N
Whe n th e ignitio n ke y i s pulle d ou t (ignitio n switc h turne d OFF ) wit h th e AUT O switc h i n th e steerin g colum n switc h O N
and th e vehicl e parke d (shif t leve r i n th e steerin g colum n wil l automaticall y mov e t o th e highes t til t positio n an d full y
retracte d positio n t o eas e exi t fro m th e vehicle .
Whe n th e ignitio n ke y i s inserte d int o th e ignitio n ke y switc h wit h th e AUT O switc h O N an d th e vehicl e parke d (shif t leve r
in th e steerin g colum n wil l automaticall y mov e bac k t o th e previou s position .
MEMOR Y RETRIEV E
When on e o f th e tw o button s o n th e drivin g positio n memor y switc h i s presse d wit h th e vehicl e parke d (shif t leve r i n
th e seat , th e mirror , an d th e steerin g colum n mov e t o th e memorize d positions .
ProCarManuals.com

Driving Positio n Memor y Syste m (DPMS )
Troubleshootin g Guid e
After completin g th e pre-troubleshootin g test s (se e pag e 23-204 ), selec t th e flowchart(s ) liste d o n th e nex t pag e fo r th e
symptom(s ) yo u wan t t o troubleshoot . I f th e symptom(s ) ar e relate d t o automati c adjusting , firs t rea d th e explanatio n fo r
th e automati c adjustmen t modes .
Automati c Adjustmen t Mode s
Mod e 1 : Whe n th e ignitio n ke y i s pulle d ou t (ignitio n switc h turne d OFF ) wit h th e AUT O switc h O N an d th e vehicl e parke d
the steerin g colum n automaticall y move s t o th e highes t til t positio n an d th e fully-retracte d
positio n t o eas e exi t fro m th e vehicle .
Mode 2 : Whe n th e ignitio n ke y is inserte d a t th e en d o f mod e 1 , withou t turnin g th e ignitio n switc h O N (II ) an d th e vehicl e
parked th e steerin g colum n wil l retur n t o th e positio n it wa s in befor e mod e 1 began .
Mode 3 : Whe n on e o f positio n button s i s presse d wit h th e vehicl e parke d an d th e ignitio n ke y i s inserted ,
the steerin g column , the sea t and th e mirror s will mov e to thei r memorize d positions.
NOTE: Th e priorit y o f th e automati c adjustment s ar e shown :
• I f th e ignitio n ke y i s no t inserted , th e steerin g colum n
i s no t adjuste d a t No . 3 to No . 4 . I t wil l b e adjuste d a t
No . 9 to No . 1 0 onl y afte r th e ke y is inserted .
• I f th e ignitio n ke y i s inserte d whil e No . 1 an d No . 2
ar e carrie d out , th e steerin g colum n wil l b e adjuste d
at No . 3 an d No . 4 .
Priorit y
1
2
3
4
5
6
7
8
9
10
Device s
Sea t slid e (backward) , mirro r
Sea t reclin e (backward )
Tilt
Extend-retrac t
Seat slid e (forward )
Sea t reclin e (forward )
Sea t fron t up-dow n
Sea t rea r up-dow n
Tilt
Extend-retrac t
ProCarManuals.com