coolant level Acura RSX 2002 Owner's Manual

This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise to near
the upper white mark. If it reaches
the red (Hot) mark, pull safely to the
side of the road. Turn to page f or
instructions and precautions on
checking the engine’s cooling
system.
This shows how much f uel you have.
It is most accurate when the car is on
level ground. It may show slightly
more or less than the actual amount
whenyouaredrivingoncurvyor
hilly roads.
The needle returns to the bottom
after you turn off the ignition. The
gauge shows the f uel level reading
immediately af ter you turn the
ignition switch back ON (II).
This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
To reset a trip meter, display it, and
then press and hold the Select/Reset
button until the number resets to
‘‘0.0’’. There are two trip meters: Trip A
and Trip B. Switch between these
displays and the odometer by
pressing the Select/Reset button
repeatedly. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
212
Gauges
Inst rument s and Cont rols
Temperature Gauge
Fuel Gauge
Trip Meter
67

Bef ore you begin driving your Acura,
youshouldknowwhatgasolineto
use, and how to check the levels of
important f luids. You also need to
know how to properly store luggage
or packages. The inf ormation in this
section will help you. If you plan to
add any accessories to your car,
please read the inf ormation in this
section f irst......................
General Precautions .154
.............................
Break-in Period .155
.........................................
Gasoline .155
.........
Service Station Procedures . 156
................
Filling the Fuel Tank . 156
....................
Opening the Hood .157
...............................
Oil Check .159
.........
Engine Coolant Check . 160
...............................
Fuel Economy .161
.....................
Vehicle Condition .161
...........................
Driving Habits .161
...
Accessories and Modif ications . 162
.............................
Carrying Cargo .164
Bef ore Driving
Bef ore Driving153

Remove the dipstick again and
check the level. It should be
between the upper and lower
marks.Look at the coolant level in the
radiator reserve tank. Make sure it is
between the MAX and MIN lines. If
it is below the MIN line, see
on page f or
inf ormation on adding the proper
coolant. Refer to
on page f or inf ormation
on checking other items in your
Acura.
If it is near or below the lower mark,
see on page .
4.
207 205
212
Engine Coolant Check
A dding
Engine Coolant Owner Maintenance
Checks
A dding Oil
Service Station Procedures
Bef ore Driving160
U UP PP
PE
ER
R M
M A
AR
RKK
M
MI
INN
M
M
A
AX
X
L
LO OW WE ER
R M
M A
AR
RKK R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K

µ
ÎÌ
ÌÌ
Î
Ì
Maint enance198
Service at the indicated distance or time whichever comes first. miles x 1,000
km x 1,000
months
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy Every 110,000 miles (176,000 km)Every 30,000 miles (48,000 km)
Service the following items at the recommended intervals
Every 110,000 miles (176,000 km) or 7 years
At 120,000 miles (192,000 km) or 10 years,
then every 60,000 miles (96,000 km) or 5 years
Check engine oil and coolant
Replace engine oil
Rotate tires (Check tire inflation and condition at least once per month)
Replace engine oil filter
Inspect front and rear brakes
Check parking brake adjustment
Visually inspect the following items:
Tie rod ends, steering gear box and boots, Suspension components
Driveshaft boots, Brake hoses and lines (including ABS)
All fluid levels and condition of fluidsExhaust system, Fuel lines and connections
Inspect and adjust drive belts
Replace dust and pollen filter
Replace transmission fluid
Replace air cleaner element
Replace spark plugs
Inspect valve clearance Inspect idle speed
Replace engine coolant
Replace brake fluid Check oil and coolant at each fuel stop
10
16
20
3230
4840
6450
8060
9670
112 80
128 90
144 100
160110
176120
192
See information on maintenance and emissions warranty, last column, page . See Dust and Pollen Filter on page for replacement information under special driving conditions. At 120,000 miles (192,000 km) or 6 years, then
every 90,000 miles (144,000 km) or 5 years
Every 3 years
24
4872
12 3660
M/T
A/T
1: : 232
197
1
Maintenance Schedule for Normal Conditions

µµ
Ø
Ø
Ø
Ø
Ø Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ì
Î
Ì Ì
Ì
Î
Maint enance199
U.S. Owners
Canadian Owners A
B
C
D
E
Service at the indicated distance or time, whichever comes first.
Refer to page to determine which schedule to use.Use the Maintenance Schedule for Severe Conditions.
10,000 mi/16,000 km/1 yr
20,000 mi/32,000 km/1 yr
30,000 mi/48,000 km/2 yrs
40,000 mi/64,000 km/2 yrs
50,000 mi/80,000 km/3 yrs
60,000 mi/96,000 km/3 yrs
70,000 mi/112,000 km/4 yrs
80,000 mi/128,000 km/4 yrs
90,000 mi/144,000 km/5 yrs
100,000 mi/160,000 km/5 yrs
110,000 mi/176,000 km
110,000 mi/176,000 km/6 yrs
110,000 mi/176,000 km/7 yrs
120,000 mi/192,000 km/6 yrs
120,000 mi/192,000 km/10 yrs Do items in A.
Do items in A, B.
DoitemsinA,C,D.
Do items in A, B.
Do items in A, E.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
DoitemsinA,C,D.
Do items in A, B.
Inspect valve clearance, cold engine.
Replace spark plugs.
Do items in A, E. Inspect idle speed.
Replace transmission fluid (M/T, A/T).
DoitemsinA,B,C,D. Replace engine coolant. Replace engine oil.
Rotate tires (follow pattern on page
238).
Replace engine oil filter.
Inspect front and rear brakes.
Check parking brake adjustment.
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks. Inspect exhaust system.
Inspect fuel lines and connections.
Inspect and adjust drive belts.
Replace dust and pollen filter.
Replace air cleaner element every 30,000 mi/48,000
km (independent of time).
Replace brake fluid every 3 years (independent of
mileage).
:
196
1:
1
See Dust and Pollen Filter on page for replacement
information under special driving conditions.
See information on maintenance and emissions warranty, last
column, page .
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
NOTE: 197 236
Maintenance Schedule for Normal Conditions (listed by distance/time)

µ
Î
Ì
ÌÌÎ
Ì
Maint enance200
Service at the indicated distance or time whichever comes first. miles x 1,000
km x 1,000
months
At 120,000 miles (192,000 km) or 10 years,
then every 60,000 miles (96,000 km) or 5 years Every 110,000 miles (176,000 km) or 7 years
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy Every 110,000 miles (176,000 km)
Service the following items at the recommended intervals
See information on maintenance and emissions warranty, last column, page .
Check engine oil and coolant
Replace engine oil
Rotate tires (Check tire inflation and condition at least once per month)
Replace engine oil filter
Inspect front and rear brakes
Lubricate all hinges, looks, and latches
Visually inspect the following items:
Tie rod ends, steering gear box and boots, Suspension components
Driveshaft boots
Check parking brake adjustment
Visually inspect the following items: Brake hoses and lines (including ABS)
All fluid levels and condition of fluidsExhaust system, Fuel lines and connections
Lights and controls, Vehicle underbody
Inspect and adjust drive belts
Replace dust and pollen filter
Replace transmission fluid
Clean or replace air cleaner element
Replace spark plugs
Inspect valve clearance Inspect idle speed
Replace engine coolant
Replace brake fluid Replace every 5,000 miles (8,000 km) or 6 months
Check oil and coolant at each fuel stop
See Dust and Pollen Filter on page for replacement information under special driving conditions. 10
16
20
3230
4840
6450
8060
9670
112 80
128 90
144 100
160110
176120
192
Every 3 years
24
4872
12 3660
1: : 197
M/T
A/T
232
1
Clean every 15,000 miles (24,000 km), and replace every 30,000 miles (48,000 km) (Use normal schedule except in dusty conditions)
Maintenance Schedule for Severe Conditions

µµ µ
µ
µ
µ µ
Engine oil level Check every
time you fill the fuel tank. See
page .
Engine coolant level Check the
radiator reserve tank every time
youfillthefueltank.Seepage . Tires Check the tire pressure
monthly. Examine the tread f or
wear and foreign objects. See page
.
Windshield washer f luid Check
the level in the reservoir monthly.
If weather conditions cause you to
use the washers f requently, check
the reservoir each time you stop
f or f uel. See page .
Automatic transmission Check
the f luid level monthly. See page .
Youshouldcheckthefollowing
items at the specif ied intervals. If
you are unsure of how to perf orm
any check, turn to the page given.
Brakes Check the f luid level
monthly. See page .Lights Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and
license plate lights monthly. See
page .
159
216
217 219 235
244
160
Owner Maintenance Checks
Maint enance205

If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks.
This coolant should always be a
mixtureof 50percentantifreezeand
50 percent water. Never add straight
antif reeze or plain water. Always use Honda All Season
Antif reeze/Coolant Type 2. This
coolant is pre-mixed with 50 percent
antif reeze and 50 percent water. It
does not require any additional
mixing. If it is not available, you may
use another major-brand non-silicate
coolant as a temporary replacement.
Make sure it is a high-quality coolant
recommended f or aluminum engines.
However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling
system to malf unction or f ail. Have
the cooling system f lushed and
ref illed with Honda antif reeze/
coolant as soon as possible.
A dding Engine Coolant
Cooling Syst em
Maint enance212
M M
I
INN
M
M
A
AX
X
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.

Make sure the engine and
radiator are cool.
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
Remove the radiator cap by
pushing down and turning
counterclockwise.Put the radiator cap back on.
Tighten it f ully. The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your car’s cooling
system. They may not be compatible
with the coolant or engine compo-
nents. 6.
5. 4.
2.
3. 1.
Cooling Syst em
Maint enance213
R RA
A D
DI
IAA T
TO
OR R C
CAA P
P
R
REES
SE ER
RV V E
E T
TA
A N
NK K

Check the level in the windshield
washer reservoir at least monthly
during normal usage. In bad weather,
when you use the washers of ten,
check the level every time you stop
f or f uel. This reservoir supplies the
windshield and rear window washers.
The cooling system capacity is:
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine.
Fill the radiator with coolant up to
the base of the f iller neck.
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.
Start the engine and let it run until
the radiator cooling f an comes on
at least twice. Then stop the
engine. Remove the radiator cap. Fill the
radiator with coolant up to the
base of the f iller neck.
Start the engine and hold it at
1,500 rpm until the radiator f an
comes on. Turn of f the engine.
Check the coolant level in the
radiator and add coolant if needed.
Install the radiator cap, and
tighten it fully.
If necessary, f ill the reserve tank
to the MAX mark. Install the
reserve tank cap.
9.
11. 10.
12.
13. 14.
15.
16. 17.
With automatic transmission:
Manual Transmission:
Maint enance
Cooling System, Windshield Washers
Windshield Washers
216
1.35 US gal (5.1, 1.12 Imp gal)
1.32 US gal (5.0
, 1.10 Imp gal)