Acura RSX 2004 Owner's Manual

Playing a T ape
Comf ort and Convenience Feat ures
A ll models except T ype-ST ype-S
98
PWR/VOL KNOB CASSETTE SLOT
FF BUTTON
FM BUTTON
PWR/VOL KNOB
PLAY/PROG BUTTON
REW BUTTON
SKIP BAR
AM BUTTON
RPT BUTTON TAPE DIRECTION INDICATOR
REPEAT INDICATORDOLBY INDICATOR
PLAY BUTTON PROG BUTTON REW BUTTON CD BUTTON
DOLBY BUTTON TAPE BUTTON
TAPE EJECT BUTTON
FF BUTTON
SKIP BUTTONS
CD/TAPE BUTTON
AM/FM BUTTON
TAPE DIRECTION INDICATOR
REPEAT BUTTONDOLBY INDICATOR
DOLBY BUTTON

Ûµ
Î
Î
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Make sure the open side of the tape
is facing right, then insert the tape
most of the way into the slot. The
system will pull the tape in the rest
of the way, and begin to play it.
The tape direction indicator will
come on to show you which side of
the tape is playing. The indicates
the side you inserted upward in now
playing. If you want to play the other
side, press the PLAY/PROG button.
When the player reaches the end of
the tape, it will automatically reverse
direction and play the other side.Dolby noise reduction turns on
when you insert a tape. The
indicator will come on in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the
NR ( ) button. Dolby remains
of f until you press the NR ( )
button again.
To remove the tape, press the
EJECT button. If you want to turn
the player of f , press the PWR/VOL
knob or turn of f the ignition. The
tape will remain in the drive. When
youturnthesystembackon,the
tape will begin playing where it lef t
off. To switch to the radio or CD player
while a tape is playing, press the
AM/FM or CD/TAPE button. To
change back to the tape player, press
the CD/TAPE button.
To switch to the radio or CD
changer while listening to a tape,
press the AM, FM, or CD button. To
change back to the tape player, press
the TAPE button.
To rewind the tape,
push the REW button. You will see
REW in the display. To fast forward
the tape, push the FF button. You
will see FF displayed. Press the FF,
REW, PLAY, or PLAY/PROG button
to take the system out of rewind or
fast forward.
Dolby noise reduction manuf actured under
license from Dolby Laboratories Licensing Corpo-
ration. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
CONT INUED
Optional on all models except Type-S
Type-S
Playing a T ape
Comf ort and Convenience Feat ures
To Play a Tape
To Stop Playing a TapeT ape Search Functions
FF/REW
99

µµ´
µ
Press the / ( )
buttons to f ind the beginning of the
current song or passage. Press the / ( ) buttons to find the
beginning of the next song or
passage. When the system reaches
the beginning of a song or passage, it
begins to play it.
Press the RPT button
to continuously play a song or
passage. You will see RPT displayed.
The track will repeat until you press
the RPT button again.
The SKIP and REPEAT
f unctions use silent periods on the
tape to find the end of a song or
passage. These f eatures may not
work if there is almost no gap
between selections, a high noise
level, or a silent period in the middle
of a selection. Thetapeplayerpicksupdirtand
oxides f rom the tape. This
contamination build up over time and
causes the sound quality to degrade.
To prevent this, you should clean the
player af ter every 30 hours of use.
If you do not clean the tape player
regularly, it may eventually become
impossible to remove the
contamination with a normal
cleaning kit. Your Acura dealer has a
cleaning kit available.
Use 100-minute or shorter tapes.
Tapes longer than that may break or
jam the drive.
If the tape is loose, tighten it by
turning the hub with a pencil or your
f inger. If the label is peeling of f ,
remove it or it could cause the tape
to jam in the player. Never try to
insert a warped or damaged tape in
the player.Store tapes in their cases to protect
them f rom dust and moisture. Never
placetapeswheretheywillbe
exposed to direct sunlight, high heat,
or high humidity. If a tape is exposed
to extreme heat or cold, let it reach a
moderate temperature bef ore
inserting it into the player.
If you see the error indication
‘‘ ’’ on the display, press the
EJECT button to remove the tape
from the unit. Make sure the tape is
not damaged. If the tape will not
eject or the error indication stays on
after the tape ejects, take the vehicle
to your Acura dealer. Never try to insert f oreign objects
into the tape player.
Type-S only
SK IP
REPEAT
Caring f or the T ape and Player
Comf ort and Convenience Feat ures
Playing a T ape
100
NOTE:

Comf ort and Convenience Feat ures
Playing a CD
A ll models except T ype-ST ype-S
101
CD/TAPE BUTTON
AM/FM BUTTON CD SLOTREPEAT INDICATOR
EJECT
BUTTON
RANDOM INDICATOR
SEEK/SKIP BAR
PWR/VOL KNOB
LOAD BUTTON CD SLOT
CD EJECT BUTTON
SKIP BUTTONS
REPEAT BUTTON
PWR/VOL KNOB REPEAT INDICATOR
RANDOM INDICATOR
CD BUTTON
FM BUTTON
AM BUTTON REPEAT BUTTON
RANDOM BUTTON
RANDOM BUTTON

´µ
´µ µ
µ
With the ignition in the
ACCESSORY (I) or ON (II) position,
insert a CD into the CD slot. The
drive will pull the CD in the rest of
the way and begin to play it. You
operate the CD player with the same
controls used f or the radio. The
number of the track playing is shown
in the display. The system will
continuously play a CD until you
change modes.
Each time you press and release
/ ( ) , the player skips
f orward to the beginning of the next
track. Press and release / ( )
to skip backward to the beginning of
the previous track. To move rapidly
within a track, press and hold the / ( ) or / ( ) . You will
see CUE or REW in the display. To continuously replay
a track, press and release the RPT
button. You will see RPT in the
display. Press the RPT button again
to turn it off.
Pressing either of the SKIP buttons
also turns of f the repeat f eature.
This f eature plays the
tracks in random order. To activate
Random Play, press and release the
RDM button. You will see RDM in
the display. This continues until you
press the RDM button again. Press the eject button ( ) to
remove the CD. If you eject the CD,
but do not remove it f rom the slot,
the system will automatically reload
the CD af ter 15 seconds and put it in
pause mode. To begin playing, press
the CD button.
Press the AM/FM button to switch
to the radio while a CD is playing.
Press the CD button to play the CD.
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or by turning off the ignition,
the CD will stay in the drive. When
youturnthesystembackon,theCD
will begin playing where it lef t of f .
Type-S only
Playing a CD, CD Changer
Comf ort and Convenience Feat ures
CD Player
To Change Tracks (SKIP)
REPEAT
RANDOM
To Stop Playing a CD
102

To load multiple CDs in one
operation:Press and hold the Load button
until you see ‘‘LOAd’’ in the
display, then release the button.
Ontheupperleftsideof the
display, the CD number f or an
empty position will begin blinking
and the green CD Loaded
indicator will come on.
Insert the CD into the CD slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way. You will see ‘‘BUSY’’ in the
display. The CD Loaded indicator
turns red and blinks as the CD is
loaded.
When LOAd appears again in the
display, insert the next CD into the
CD slot. Repeat this until all six positions
are loaded. The system will then
begin playing the last CD loaded.
If you are not loading CDs into all six
positions, press the Load button
again after the last CD has loaded.
The system will begin playing the
last CD loaded.
If you stop loading CDs bef ore all six
positions are f illed, and you do not
press the Load button, the system
will wait f or 10 seconds, then stop
the load operation and begin playing
the last CD loaded.
To load CDs or operate the CD
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position. Your Acura’s audio system has an in-
dash CD changer that holds up to six
CDs, providing several hours of
continuous entertainment. You
operate this CD changer with the
same controls used f or the radio and
tape player.
Load and play only standard round
CDs. Odd-shaped CDs may jam in
the drive or cause other problems.
You cannot load and play 3-inch (8
cm) CDs in this system. 1.
2.
3.
4.5.
CONT INUED
Type-S
Playing a CD, CD Changer
Comf ort and Convenience Feat ures
Operating the CD ChangerL oading CDs in t he Changer
103

µ
To load a single CD:
Press and release the Load button.
When the CD number f or an
empty position starts to blink and
the green CD Loaded indicator
comeson,youwillseeLOAdin
the display. Insert the CD into the
CD slot. Insert it only about
half way, the drive will pull it in the
rest of the way.
The system will load the CD, and
begin playing it. If you press the Load button while a
CD is playing, the system will stop
playing that CD and start the loading
sequence. It will then play the CD
just loaded.
You can also load a CD into an empty
position while a CD is playing by
pressing the appropriate preset
button. Select an empty position (the
CD Loaded indicator is of f ), and
press the preset button f or that
position (1 to 6). The system will
stop playing the current CD and start
the loading sequence. It will then
play the CD just loaded. Select the CD changer by pressing
the CD button. You will see ‘‘Cd’’ in
the display. The system will begin
playing the last selected CD in the
CD changer. You will see the CD and
track numbers displayed.
When that CD ends, the next CD in
the CD changer is loaded and played.
Af ter the last CD f inishes, the
system returns to CD 1.
To select a dif f erent CD, press the
appropriate Preset button (1
6). If
youselectanemptypositioninthe
CD changer, the system will go into
the loading sequence (see page ).
You can use the SKIP buttons while
a CD is playing to select passages
and change tracks.
1.
2.
3.
103
Playing a CD, CD Changer
Comf ort and Convenience Feat ures
Operat ion
104

Ó
ÓÓÓ µ
µ´
µ ´µ
To move rapidly within a track, press
and hold the appropriate SKIP
button. You will hear a beep and the
system will continue to move. Press
the button to move forward, or
the button to move backward.
Release the button when the system
reaches the point you want.
Each time you press the button
and release it, the system skips
f orward to the beginning of the next
track. Press and release the
buttontoskipbackwardtothe
beginning of the current track. Press
and release it again to skip to the
beginning of the previous track. To activate the Repeat
f eature, press and release the RPT
button. You will see RPT in the
display as a reminder. The system
continuously replays the current
track. Press the RPT button again to
turn it off. Pressing either of the
SKIP buttons also turns off the
repeat feature.
This feature,
when activated, plays the tracks
within a CD in random order, rather
than in the order they are recorded
on the CD. To activate Random Play,
press the RDM button. You will see
RDM in the display. The system will
then select and play tracks randomly.
This continues until you deactivate
RandomPlaybypressingtheRDM
button again, or you select a
dif f erent CD with a preset button. To take the system out of CD mode,
press the AM or FM button, or insert
a tape in the player. If a tape is
already in the tape player, press the
TAPE button. When you return to
CD mode by pressing the CD button,
play will continue at the same point
that it lef t of f .
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
CONT INUED
Playing a CD, CD Changer
REPEAT
RANDOM PLAY
Comf ort and Convenience Feat ures105

To remove the CD that is currently
playing, press the eject button. You
will see ‘‘EJEC’’ in the display. When
you remove the CD f rom the slot,
the system automatically begins the
Load sequence so you can load
another CD in that position. If you do
not load another CD, af ter 10
seconds the system begins playing
the next CD in the changer. If the
changer is empty, the system selects
the previous mode (AM, FM, or
Tape).
If you do not remove the CD f rom
the slot, the system will reload the
CD af ter 15 seconds and put the CD
changer in pause mode. To begin
playing the CD, press the CD button.
To remove a different CD from the
changer,firstselectitwiththe
appropriate preset button. When that
CD begins playing, press the eject
button.If you press the Eject button while
listening to the radio or tape, or with
the audio system turned of f , the CD
that was last selected is ejected.
After that CD is ejected, pressing the
Eject button again will eject the next
CD in the numerical order. By doing
this six times, you can remove all the
CDs f rom the changer.
In any mode, if you press the eject
button and hold it until you hear a
beep, the system will eject all of the
CDs in the changer.
You can also eject CDs when the
ignition switch is of f . The CD that
was last selected is ejected f irst. You
can eject up to six CDs, one at a time.
Playing a CD, CD Changer
Removing CDs f rom t he Changer
Comf ort and Convenience Feat ures106

µ´
To select the CD changer, press the
CD button. The CD and track
numbers will be displayed. To select
a dif f erent CD, use the preset 5
(DISC ) or preset 6 (DISC )
button. If you select an empty slot in
the magazine, the changer will, af ter
f inding that slot empty, try to load
the CD in the next slot.
Load the desired CDs in the
magazine, and load the magazine in
the changer according to the
instructions that came with the unit. A CD changer is available f or your
vehicle. It holds up to six CDs. You
operate the CD changer with the
same controls used f or the in-dash
CD player.
Optional on all models except Type-S
Playing a CD, CD Changer
Comf ort and Convenience Feat ures
Operating the Optional CD
Changer
107