instrument panel Acura RSX 2006 User Guide

The instrument panel has many
indicators to give you important
inf ormation about your vehicle.
This indicator comes on when you
turn the ignition switch to the ON
(II) position. It reminds you and your
passengers to f asten your seat belts.
A beeper also sounds if you have not
f astened your seat belt.This indicator comes on when you
turn the ignition switch to the ON
(II) position. If it comes on at any
other time, it indicates a potential
problem with your f ront airbags.
This indicator will also alert you to a
potential problem with your side
airbags, passenger’s side airbag
automatic cutoff system, or
automatic seat belt tensioners. For
more information, see page .This indicator comes on when you
turn the ignition switch to the ON
(II) position. If it comes on at any
other time, it indicates that the
passenger’s side airbag has
automatically shut off. For more
inf ormation, see page .
If you do not f asten your seat belt,
the beeper will stop af ter a f ew
seconds but the indicator stays on.
Both the indicator and the beeper
stay of f if you f asten your seat belt
bef ore turning on the ignition switch.
If you continue driving without
f astening your seat belt, the beeper
sounds and the indicator f lashes
again at regular intervals. 26
27
Instrument Panel Indicators
Supplemental Restraint
System Indicator
Seat Belt Reminder
Indicator Side Airbag Of f
Indicator
52
U.S.
Canada

This indicator has two f unctions:If this indicator comes on when the
engine is running, the battery is not
being charged. For more inf ormation,
see page .
The engine can be severely damaged
if this indicator f lashes or stays on
when the engine is running. For
more information, see page .
See page .
Itcomesonwhenyouturnthe
ignition switch to the ON (II)
position. It is a reminder to check
the parking brake. Driving with
the parking brake not f ully
released can damage the brakes
and tires.
If it remains lit af ter you f ully
release the parking brake while
the engine is running, or if it
comes on while driving, there
could be a problem with the brake
system. For more inf ormation, see
page . This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position, and when the ignition
switch is turned to the START (III)
position. If it comes on at any other
time, there is a problem with the
ABS. If this happens, have your
vehicle checked at a dealer. With the
indicator on, your vehicle still has
normal braking ability but no anti-
lock brakes. For more inf ormation,
see page .
1.
2. 216
216
217
159
218 Parking Brake
and Brake
System
Indicator
Charging System
Indicator
L ow Oil Pressure
Indicator
Malf unction Indicator
Lamp
Anti-lock Brake System
(A BS) Indicator
Instrument Panel Indicators
Inst rument s and Cont rols
53
U.S. Canada

Only on models equipped with CruiseControl System
This indicator comes on when you
set the cruise control. See page f or inf ormation on operating the
cruise control. This indicator comes on f or a f ew
seconds when you turn the ignition
switch to the ON (II) position. It will
gooffifyouhaveinserteda
properly-coded ignition key. If it is
not a properly-coded key, the
indicator will blink and the engine
will not start (see page ).
This indicator also blinks several
times when you turn the ignition
switch f rom the ON (II) position to
the ACCESSORY (I) or the LOCK
(0) position.
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
This indicator comes on if either
door or the hatch is not closed
tightly.
This indicator comes on with the
high beam headlights. For more
inf ormation, see page .
On Canadian models, this indicator
comes on with reduced brightness
when the daytime running lights
(DRL) are on (see page ). 65
186
61
61
127
Instrument Panel Indicators
Cruise Control Indicator
Turn Signal and
Hazard Warning
Indicators Immobilizer System
Indicator
Door and Hatch Open
Indicator
High Beam Indicator
54

This indicator comes on when you
turn the ignition switch to the ON
(II) position with the headlight
switch of f and the parking brake set.
It should go of f if you turn on the
headlights or release the parking
brake. If it comes on at any other
time, it means there is a problem
withtheDRL.Theremayalsobea
problem with the high beam
headlights.This indicator comes on when the
washer f luid level is low. Add washer
f luid when you see this indicator
come on (see page ).
This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance.
Ref er to the maintenance schedule
f or normal and severe driving
conditions on pages and .
For the f irst 8,000 miles (12,800 km)
af ter the maintenance required
indicator is reset, it will come on f or
2 seconds when you turn the ignition
switch to the ON (II) position.
Between 8,000 miles (12,800 km)
and 10,000 miles (16,000 km), it will
come on f or 2 seconds when you
first turn the ignition switch to the
ON (II) position, and then f lash f or
10 seconds.
This indicator comes on as a
reminder that you must ref uel soon.
When the indicator comes on, there
is about 1.9 US gal (7.5
)of fuel
remaining in the tank bef ore the
reading reaches E. There is a small
reserve of f uel remaining in the tank
when the reading does reach E. 179
169170
Canadian models only Canadian models only
Instrument Panel Indicators
Washer L evel IndicatorMaintenance Required
Indicator
Low Fuel Indicator
Daytime Running L ights
Indicator
Inst rument s and Cont rols
55

This indicator comes on when the
security system is set. See pagef or more inf ormation on the
security system.
If you exceed 10,000 miles (16,000
km) without having the scheduled
maintenance perf ormed, this
indicator will remain on as a constant
reminder.
Your dealer will reset this indicator
af ter completing the scheduled
maintenance. If this maintenance is
done by someone other than your
dealer, reset the indicator as f ollows.
Turn of f the engine. Press and hold the select/reset
knob in the instrument panel, then
turn the ignition switch to the ON
(II) position.
Hold the knob f or about10
seconds until the indicator goes
off.
1.
2.
3. 126
Security System Indicator
Instrument Panel Indicators
56
SECURITY SYSTEM INDICATOR
SELECT/RESET KNOB

ÎÎ
Î
Î
Î
ÎTo use the horn, press the center pad on the steering wheel.
If equipped.
1:
2:
Controls Near the Steering Wheel
Inst rument s and Cont rols
59
WINDSHIELD
WIPERS/WASHERS
REAR WINDOW DEFOGGER
HAZARD WARNING BUTTON
HEADLIGHTS/TURN SIGNALS INSTRUMENT PANEL BRIGHTNESS
(P.62)
(P.62)
(P.62)
(P.60)
HORNCRUISE CONTROL BUTTONS
(P.63) (P.128)
(P.127)
(P.79) STEERING WHEEL ADJUSTMENT
CRUISE CONTROL
MASTER SWITCH
MOONROOF SWITCH(P.61)
1 2
2
2

µ
µ µ
Turning the switch to the ‘‘ ’’
position turns on the headlights. If
you leave the lights on with the key
removed f rom the ignition switch,
you will hear a reminder beeper
when you open the driver’s door. To turn on the high
beams, push the lef t lever f orward
until it clicks. The blue high beam
indicator will come on (see page ).
Pull it back to return to low beams.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
Push down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to center when you release it or
complete a turn.
The headlights revert to normal
operation when you turn them on
with the switch. With the headlight switch off, the
high beam headlights come on with
reduced brightness when you turn
the ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
Turn signal
Of f
Parking and interior lights
Headlights
High beams
Flashhighbeams Turning the switch to
the ‘‘ ’’ position turns on the
parking lights, taillights, instrument
panel lights, side-marker lights, and
rear license plate lights.
1.
2.
3.
4.
5.
6. 54
Canadian model only
Turn Signal and Headlights Daytime Running L ights
High Beams
Turn Signal Headlights
Turn Signal and Headlights
Inst rument s and Cont rols
61

The knob on the instrument panel
controls the brightness of the
instrument panel. Turn the knob to
adjust the brightness.Pushtheredbuttontoturnonthe
hazard warning lights (f our-way
flashers). This causes all four
outside turn signals and both
indicators in the instrument panel to
f lash. Use the hazard warning lights
if you need to park in a dangerous
area near heavy traffic, or if your
vehicle is disabled.The rear window def ogger will clear
fog, frost, and thin ice from the
window. Push the def ogger button to
turn it on and off. The indicator in
the button comes on to show the
def ogger is on. If you do not turn it
of f , the def ogger will shut itself of f
af ter about 25 minutes. It also shuts
of f when you turn of f the ignition
switch. You have to turn it on again
when you restart the vehicle. Rear Window Def ogger
Instrument Panel Brightness Hazard Warning Button
Instrument Panel Brightness, Hazard Warning Button, Rear Window Def ogger
62

Make sure the rear window is clear
and you have good visibility bef ore
starting to drive.
Thedefoggerwiresontheinsideof
the rear window can be accidentally
damaged. When cleaning the glass,
always wipe side-to-side.Make any steering wheel adjustment
bef ore you start driving.
Push the lever under the steering
column all the way down. Move the steering wheel so it
points to your chest, not toward
your f ace. Make sure you can see
the instrument panel gauges and
indicators.
Push the lever up to lock the
steering wheel in position.
Make sure you have securely
locked the steering wheel in place
by trying to move it up and down.
1.
2.
3.
4.
Steering Wheel A djustment
Rear Window Def ogger, Steering Wheel A djustment
Inst rument s and Cont rols
63
Adjusting the steering wheel
position while driving may
cause you to lose control of the
vehicle and be seriously injured
inacrash.
Adjust the steering wheel only
when the vehicle is stopped.

µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shif t
lever must also be in park. If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position. You can
operate the audio system and the
accessory power socket in this
position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key. You will hear a reminder beeper if
you leave the key in the LOCK (0) or
the ACCESSORY (I) position and
open the driver’s door. Remove the
key to turn of f the beeper.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
Ignition Switch
LOCK (0)
ON (II) A CCESSORY (I)
ST A RT (III)
66
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.