codes Acura TL 2002 3.2 Owner's Manual

µ
If you are training the second or
third buttons, go directly to Step 1. Unplug the garage door opener
motor f rom the house current.
Bef ore you can use HomeLink to
operate devices around your home, it
must ‘‘learn’’ the proper codes. For
example, to train HomeLink to open
and close the garage door:
If you just took
delivery of your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button. To do this,
press and hold the two outside
buttons on the HomeLink
transceiver for about 20 seconds,
until the red light f lashes. Release
the buttons, then proceed to Step 1.
Holdtheendof thegaragedoor
opener remote control 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red light in HomeLink. Select the HomeLink button you
want to train.
Press the button on the remote
control and the button on
HomeLink at the same time. Hold
down both buttons.
2. 3.
4.
1.
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures
T raining HomeL inkBef ore you begin
158
00/12/25 14:19:21 31S0K630_161

CONT INUED
Canadian Owners:
The remote control you are training
from may stop transmitting after two
seconds. This is not long enough f or
HomeLink to learn the code. Release
and press the button on the remote
control every two seconds until
HomeLink has learned the code.For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Inf ormation f rom
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.
The‘‘Training HomeLink’’ procedure
trains HomeLink to the proper
garage door opener code. The
f ollowing procedure synchronizes
HomeLink to the garage door opener
so they send and receive the correct
codes.
The red light in HomeLink should
begin f lashing. It will f lash slowly
at first, then rapidly.
When the red light f lashes rapidly,
release both buttons. HomeLink
should have learned the code from
the remote control.
Plug in the garage door opener
motor, then test the HomeLink
transceiver button by pushing it. It
should operate the garage door.
If the button does not work, repeat
this procedure to train it again. If it
still does not work, you may have a variable or rolling code garage
door opener. Test this by pressing
and holding the HomeLink
transceiver button you just trained.
If the red light blinks f or two
seconds,thenstayson,youhavea
rolling code garage door opener.
You may be able to verify this with
the manufacturer’s documentation.
Go to ‘‘Training With a Rolling
Code System.’’
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely-
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
5.
6.
8.
7. T raining With a Rolling Code
System
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures159
00/12/25 14:19:32 31S0K630_162

As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Toerasethecodesstoredinallthree
buttons, press and hold the two
outside buttons until the red light
begins to f lash, then release the
buttons.
Youshoulderaseallthreecodes
bef ore selling the car.
Totrainanalreadyprogrammed
HomeLink button to operate a new
device:
Select the HomeLink button you
want to train.
Press and hold the HomeLink
button until the red light begins to
f lash slowly (approximately 20
seconds).
While continuing to hold the
HomeLink button, place the
remotecontrolforthedevice2to
5inchesfromHomeLink. Release both buttons. HomeLink
should now be trained to operate
the device.
Press and hold the button on the
remote control. Hold both buttons
until the red light begins to f lash
rapidly.
1.
2.
3.
4. 5.
Retraining a Button
Erasing Codes
HomeL ink Universal T ransceiver
Comf ort and Convenience Feat ures161
00/12/25 14:19:56 31S0K630_164

This section covers the more-
common problems that motorists
experience with their vehicles. It
gives you inf ormation about how to
safely evaluate the problem and what
to do to correct it. If the problem has
stranded you on the side of the road,
you may be able to get going again.
If not, you will also f ind instructions
on getting your car towed.......................
Compact Spare Tire . 278
....................
Changing a Flat Tire . 279
..........
If Your Engine Won’t Start . 285
Nothing Happens or the Starter Motor Operates ............................
Very Slowly . 285
The Starter Operates ................................
Normally . 286
................................
Jump Starting . 286
............
If Your Engine Overheats . 289
.........
Low Oil Pressure Indicator . 291
..........
Charging System Indicator . 292
.......
Malf unction Indicator Lamp . 293
.......................
Readiness Codes .294
...............
Brake System Indicator . 295
..................
Closing the Moonroof . 296
..............................................
Fuses .297
..........
Checking and Replacing . 298
......................
Emergency Towing .302
Taking Care of the Unexpected
T aking Care of t he Unexpect ed277
00/12/25 14:39:17 31S0K630_280

Your car has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
If your car’s battery has been
disconnected or gone dead, these
codes are erased. It takes several
days of driving under various
conditions to set the codes again.If possible, do not take your vehicle
f or a state emissions test until the
readiness codes are set. To check if
they are set, turn the ignition ON (II),
but do not start the engine. The
Malf unction Indicator Lamp will
come on f or 20 seconds. If it then
goes of f , the readiness codes are set.
If it blinks 5 times, the readiness
codes are not set. Ref er to State
Emissions Testing f or more
inf ormation.(See page .)
317
Malf unction Indicator L amp
T aking Care of t he Unexpect ed
Readiness Codes
294
00/12/25 14:42:08 31S0K630_297

CONT INUED
If you take your vehicle f or a state
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions.If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle re-tested within the
next two or three days, you can
condition the vehicle for re-testing
by doing the f ollowing.
Make sure the gas tank is nearly,
but not completely, f ull (around
3/4).
Make sure the vehicle has been
parked with the engine of f f or 8
hours or more.
Make sure the ambient
temperature is between 20° and
95°F. Without touching the accelerator
pedal, start the engine and let it
idle f or 20 seconds.
Keep the vehicle in Park .
Increase the engine speed to 2,000
rpm and hold it there until the
temperature gauge rises to at least
1/4of thescale(approximately3
minutes).
T echnical Inf ormation
St at e Emissions T est ing
T esting of Readiness Codes
317
00/12/25 14:46:00 31S0K630_320

Select a nearby lightly traveled
major highway where you can
maintain a speed of 50 to 60 mph
f or at least 20 minutes. Drive on
the highway in D . Do not use the
cruise control. When traf f ic allows,
drive f or 90 seconds without
moving the accelerator pedal.
(Vehicle speed may vary slightly;
this is okay.) If you cannot do this
f or a continuous 90 seconds
because of traf f ic conditions, drive
f or at least 30 seconds, then repeat
it two more times (f or a total of 90
seconds).
Then drive in city/suburban
traffic for at least 10 minutes.
When traf f ic conditions allow, let
the vehicle coast f or several
seconds without using the
accelerator pedal or the brake
pedal.If the testing f acility determines the
readiness codes are still not set, see
your Acura dealer.
5
St at e Emissions T est ing
T echnical Inf ormation318
00/12/25 14:46:05 31S0K630_321

Î..................................
Saf ety Belts . 8, 44
.........
Safety Defects, Reporting . 323
.................................
Saf ety Features .7
...........................................
Airbags .9
..................................
Door Locks .10
..........................
Head Restraints .10
.......................................
Seat Belts .8
.....................
Seats & Seat-Backs .10
.............
Saf ety Labels, Location of . 54
...............................
Saf ety Messages . ii
.....................................
Seat Belts .8, 44
...............
Additional Information . 44
.....................................
Cleaning .273
................
Lap/Shoulder Belt . 15, 44
................................
Maintenance .46
Reminder Light and ................................
Beeper .44, 59
..............................
Paint Touch-up .271
..............
Panel Brightness Control . 71
........................
Park Gear Position .182
...........................................
Parking .189
...............................
Parking Brake .104
Parking Brake and Brake System ...............................
Indicator .59, 295
.................................
Parking Lights .69
..
Parking Over Things that Burn . 189
.............................
PGM-FI System .315
..................
Polishing and Waxing . 271
............
Pre-Drive Saf ety Checklist . 11
.........
Pregnancy, Using Seat Belts . 19
............................
Protecting Adults .12
...
Additional Safety Precautions . 20
.....
Advice f or Pregnant Women . 19
........................
Protecting Children .21
.......................
Protecting Inf ants .30
.......
Protecting Larger Children . 37
.........
Protecting Small Children . 34
Using Child Seats with .....................................
Tethers .41 ...................
Radiator Overheating . 289
Radio/Cassette/CD Sound ........................................
System .129
...................
Readiness Codes . 294, 317
..
Rear Lights, Bulb Replacement . 263
..........................
Rear Seat Armrest .92
............................
Rear View Mirror .94
.................
Rear Window Def ogger . 74
...............
Reclining the Seat Backs . 89
.............................
Reminder Lights .57
................
Remote Audio Controls . 150
.......................
Remote Transmitter .81
Replacement Inf ormation .................
Air Cleaner Element . 238
.............
Air Conditioning Filter . 249
..........................
Engine Coolant .230
................
Engine Oil and Filter . 225
..........................................
Fuses .298
................................
Light Bulbs .259
....................................
Schedule .214
................................
Spark Plugs .240
...........................................
Tires .254
.............................
Wiper Blades .246 Replacing Seat Belts Af ter a
............................................
Crash .46
...
Reserve Tank, Engine Coolant . 169
...............................
Restraint, Child .21
..................
Reverse Gear Position . 182
................................
Rotation, Tire .254
Index
PR
S
VI
00/12/25 14:47:47 31S0K630_335