lock Acura TL 2003 3.2 Repair Manual

µ
Ì
Î
Î
Î
Ì
Ì Î
Î
Î
µ
Ì
Follow the Severe Conditions
Maintenance Schedule if you
drive your car under
one or more of the f ollowing
conditions:Driving less than 5 miles (8
km) per trip or, in f reezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving,
such as a taxi or a commecial
delivery vehicle.
Trailer towing, driving with a
roof rack, or driving in
mountainous conditions.
Driving on muddy, dusty, or
de-iced roads.
Follow the Maintenance
Schedule f or Severe Conditions.
MAINLY
Maint enance
U.S. Owners
Canadian Owners
226
Visually inspect the following items:
Service at the indicated
distance or time whichever
comes first.
miles x 1,000
km x 1,000
months
Replace every 3,750 miles (6,000 km) or 6 monthsCheck oil and coolant at each fuel stop
Tie rod ends, steering gear box, and boots
Suspension components
Driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and conditions of fluids
Cooling system hoses and connections Exhaust system
Fuel lines and connections
Lights and controls, Vehicle underbody Rotate tires every 7,500 miles (12,000 km)
Inspect every 7,500 miles (12,000 km) or 6 months
Every 7,500 miles (12,000 km) or 6 monthsEvery 3 years (independent of mileage)
See timing belt on page for replacement information under special driving conditions. 15
24
12
30
48
2445
72
3660
96
4875
120 60 90
144 72 105
168
84 120
192
96
120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years
60,000 miles (96,000 km) or 36 months, then every 30,000 miles (48,000 km) or 24 months
Replace engine oil and oil filter
Check engine oil and coolant
Clean ( ) or replace ( ) air cleaner element
Inspect valve clearance
Replace spark plugs
Inspect and adjust drive belts
Inspect idle speed
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition
at least once per month)
See dust and pollen filter on page for replacement information under special driving conditions. See information on maintenance and
emissions warranty, last column, page
.
Adjust only if noisy
:
1:
2:
3: Premium model only
223
260
259
1
2
3
Use normal schedule except in dusty conditions
Replace timing belt , and inspect water pump
Maintenance Schedule for Severe Conditions

µµ
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ì
Ì
Î
Î
Î
ÌÎ Î
CONT INUED
Maint enance227
A, B, C, D, E
U.S. Owners
Canadian Owners
A
B
C
D
Service at the indicated distance or time, whichever comes first. Do the items in
as required for each distance/time.
Refer to page to determine which schedule to use. Use the Maintenance Schedule for Severe Conditions.
3,750 mi/6,000 km
7,500 mi/12,000 km
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
45,000 mi/72,000 km/3 yrs
3yrs
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/4 yrs
60,000 mi/96,000 km/3 yrs
63,750 mi/102,000 km
67,500 mi/108,000 km
71,250 mi/114,000 km
75,000 mi/120,000 km/5 yrs
78,750 mi/126,000 km Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page
264).
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Lubricate all hinges, locks and latches with
multipurpose grease.
Inspect brake hoses and lines (including ABS).
Check all fluid levels, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections. Inspect exhaust system.
Inspect fuel lines and connections.
Check all lights.
Inspect the underbody.
Replace air cleaner element.
Inspect and adjust drive belts.
Replace dust and pollen filter .
Do items in A.
Do items in A, B.
Do items in A.
Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A. Clean air cleaner element.
DoitemsinA,B,C. Replace brake fluid every 3 years,independent
of mileage.
Do items in A.
Do items in A, B.
Do items in A. Replace timing belt , and inspect water pump.
DoitemsinA,B,C,D. Replace transmission fluid.
Do items in A.
Do items in A, B.
Do items in A. Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
226
3
1
1
2 1
Maintenance Schedule for Severe Conditions (listed by distance/time)

CONT INUED
Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system. Make sure the engine and radiator
are cool.Remove the radiator cap by
pushing down and turning
counterclockwise.
The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Put the radiator cap back on.
Tighten it f ully.
3.
1.
2. 4.
5.
Cooling Syst em
Maint enance239
R RA
A D
DI
IAA T
TO
OR R C
CAA P
P

CONT INUED
Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Turn the ignition ON (II). Turn
the heater temperature control
dial to maximum heat (climate
control to 90°F/32°C). Turn of f
the ignition. Open the hood. Make
sure the engine and radiator are
cool to the touch.
Remove the radiator cap. Loosen the drain plug on the
bottom of the radiator. The
coolant will drain through the
splash guard.
Install a rubber hose on the drain
bolt at the rear of the engine
cylinder block. Loosen the drain
bolt.
3.
1.
2. 4.5.
6.
Cooling Syst em
Maint enance241
D D
R
RAA I
INN P
PL
LUUG G R
REES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
H
H O
OL LDD E
ER
R R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K
D
D R
RAA I
INN B
BOOL LTT

Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque:Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.
The cooling system capacity is:
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine. Pour coolant into theradiator up to the base of the f iller
neck.
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
Install the radiator cap, and
tighten it to the first stop.
7.
8.
9.10.
11.
Cooling Syst em
Maint enance242
F Fi illll u
u p
p t
too h
he
erree
7 lbf·ft (9.8 N·m , 1.0 kgf·m)
1.48 US gal (5.6
, 1.23 Imp gal)

Check the level when the engine is
cold. Look at the side of the
reservoir. The f luid should be
between the UPPER LEVEL and
LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
f luid to the UPPER LEVEL.Always use Honda Power Steering
Fluid. If it is not available, you may
use another power steering f luid as
an emergency replacement.
However, continued use can cause
increased wear and poor steering in
cold weather. Have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently and have
the system inspected as soon as
possible.
Clean the hood latch assembly with a
mild cleaner, then lubricate it with a
multipurpose grease. Lubricate all
the moving parts (as shown),
including the pivot. Follow the time
and distance recommendations in
the Maintenance Schedule. If you
are not sure how to clean and grease
the latch, contact your Acura dealer.
Maint enance
Power Steering Hood L atch
Power Steering, Hood L atch
247
M MA
AX
X
M
M I
INN L
LA
A T
TC
CH H
A
A S
SSSEEM
M B
BLLYY
T urning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

Disconnect the wire connector
f rom the ignition coil by pushing
on the lock tab and pulling on the
connector. Pull on the plastic
connector, not the wires.
Loosen the two holding clips by
turning the heads one-quarter turn
counterclockwise with a f lat-tipped
screwdriver. Remove the cover on
the f ront cylinder bank by pulling
it straight up.
Clean up any dirt and oil that have
collected around the ignition coils.
The spark plugs in your car are a
special platinum-tipped design f or
longer lif e. The spark plugs should
be replaced according to the time
and distance recommendations in
the maintenance schedule.
1.
2.3.
Replacement
Spark Plugs
Maint enance250
H H
O
OL LDD I
INNG G
C
CL LIIPP L
LO
OC CKK T
TA
A B
B

´
µ
´
µ
Push the wire connector onto the
ignition coil. Make sure it locks in
place. Install the ignition coil. Reinstall
the hexagon socket head cap bolt. Repeat this procedure f or the
other f ive spark plugs.
Reinstall the cover on the front
cylinder bank while putting its
mounting clip in the hole on the
passenger’s side. Secure the cover
by turning the heads of the two
holding clips one-quarter turn
clockwise with a f lat-tipped
screwdriver.
Spark Plug Gap: Spark Plug Gap:NGK:
DENSO:
8. 11.
10.
9. NGK:
DENSO:
Specif ications:
Spark Plugs
Maint enance
Premium model
T ype-S
252
0.04 in (1.1 mm) PKJ20CR-M11 PZFR6E-11
0.04 in (1.1 mm) PKJ16CR-L11
PZFR5F-11
0
0.1 mm
0
0.1 mm
Tighten the spark plugs caref ully. A
spark plug that is too loose can
overheat and damage the engine.
Overtightening can cause damage to
the threads in the cylinder head.

µ
Check the condition of the wiper
blades at least every six months.
Look f or signs of cracking in the
rubber, or areas that are getting
hard. Replace the blades if you f ind
these signs, or if they leave streaks
and unwiped areas when used.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold it in while you
push the blade assembly toward
thebaseof thearm.
To replace the blade:
Raise the wiper arm of f the
windshield. Turn the ignition ON (II), switch
the wipers to INT or (low
position), then turn the ignition
OFF when the wiper arm is
approximately midway in its travel.
2. 1. 3.
Wiper Blades
Maint enance256
W WI
IPP E
ER
R A
AR
RMM S
S
L
LOOC CKK T
TA
A B
B

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.Examine the new wiper blades. If
they have no plastic or metal rein-
f orcement along the back edge,
remove the metal reinf orcement
strips f rom the old wiper blade and
install them in the slots along the
edge of the new blade.Slide the new wiper blade into the
holder until the tabs lock.
Lower the wiper arm down against
the windshield. Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Turn the ignition switch ON (II)
andreturnthewindshieldwipers
to their park position.
4. 5. 6.
7.
8.
9.
Wiper Blades
Maint enance257
R RE EI
INNF FOOR RCCEEM
M E
EN
NT T
B
BL
LAA D
DE
E B
BLLAA D
DE
E