display Acura TL 2004 Service Manual

Your vehicle’s audio system will
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic f ive-digit code in the
preset buttons. Because there are
hundreds of number combinations
possible f rom f ive digits, making the
system work without knowing the
exact code is nearly impossible.
Youshouldhavereceivedacardthat
lists your audio system code number
and serial number. It is best to store
this card in a saf e place at home. In
addition, you should write the audio
system’s serial number in this
Owner’s Manual.
If youshouldhappentolosethecard,
you must obtain the code number
f rom an Acura dealer. To do this,
you will need the system’s serial
number.If your vehicle’s battery is discon-
nected or goes dead, the audio
system will disable itself . If this
happens, you will see ‘‘CODE’’ in the
frequencydisplaythenexttimeyou
turn on the system. Use the preset
buttons to enter the five-digit code.
The code is located on the radio code
card included in your Owner’s
Manual kit. When it is entered
correctly, the radio will start playing.
If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have ten tries to
enter the correct code. If you are
unsuccessful in ten attempts, you
must then leave the system on for 1
hour bef ore trying again.
If thecodecardislost,anAcura
dealer can access your code with
your radio’s serial number. To
access the serial number, turn the
radio on. It must display ‘‘CODE’’,then turn the radio off. Push the
preset 1, preset 6, and power buttons
at the same time, then quickly
release. The serial number will
appear in two sets of f our digits.
You will have to store your favorite
XM stations in the preset buttons
af ter the system begins working.
Your original setting were lost when
the power was disconnected.
Radio T hef t Prot ect ion
Comf ort and Convenience Feat ures
Radio T hef t Protection
140

The security system sets
automatically 15 seconds after you
lock the doors, hood, and trunk. For
the system to activate, you must lock
the doors f rom the outside with the
key, lock tab, door lock switch, or
remote transmitter. The security
system indicator next to the driver’s
door lock starts blinking immediately
to show you the system is setting
itself .With the system set, you can still
open the trunk with the remote
transmitter without triggering the
alarm. The alarm will sound if the
trunk is opened with the trunk
releasebuttononthedriver’sdoor,
thetrunkreleasehandlebehindthe
trunk pass-through cover, or the
emergency trunk opener.
The security system will not set if
the hood, trunk, or any door is not
f ully closed. If the system will not set,
check the Door and Trunk Open
Monitor on the multi-inf ormation
display (see page ) to see if the
doors and trunk are f ully closed.
Since it is not part of the monitor
display, manually check the hood.
Do not attempt to alter this system
or add other devices to it.
The security system helps to protect
your vehicle and valuables f rom thef t.
The horn sounds and a combination
of headlights, parking lights, side
marker lights and taillights f lash if
someone attempts to break into your
vehicleorremovetheradio.This
alarm continues f or 2 minutes, then
the system resets. To reset an
alarming system bef ore the 2
minutes have elapsed, unlock the
driver’s door with the key or use the
remote transmitter.
Once the security system is set,
opening any door or the hood
without using the key or the remote
transmitter will cause the system to
alarm. It also alarms if the radio is
removed f rom the dashboard or the
wiring is cut. 60
Security System
Comf ort and Convenience Feat ures141
SECURITY SYSTEM LIGHT

ε
Î
Î
To operate the HFL, use the HFL
Talk and Back buttons on the left
side of the steering wheel. On
navigation-equipped vehicles, there
are two sets of buttons: one f or the
navigation, climate control, and audio
systems, and the other f or the HFL. When you are operating the HFL, or
when you manually scroll through
the Multi-Information Display and
select HFL, you will see this
inf ormation on the screen:
Signal Strength Indicates the
network signal strength of the
current phone call. Five bars
equals f ull strength.
Here is the function of each HFL
button:
HFLTalk:Thisbuttonisusedbefore
you give a command, to answer
incoming calls, and to conf irm
system inf ormation.
HFLBack:Thisbuttonisusedto
end a call, go back to the previous
voice control command, and to
cancel an operation.
HandsFreeL ink
HFL Buttons
Multi-Inf ormation Display
Comf ort and Convenience Feat ures150
NAVIGATION
SYSTEM
BUTTONSHFL TALK
BUTTON
SIGNAL
STLENGTH
PHONE DIALINGBATTERY LEVEL
STATUS
HFL
MODE
HFL BACK
BUTTON ROAM STATUS
Refer to your navigation system
Manual.
TM

Î
Î
Î
Î
µ
µ µ
µ
µ
µ µ
Î Î
CONT INUED
This inf ormation is displayed
whetherornotthephoneisbeing
used:ROAM Status (models without
navigation system) Indicates
your phone is roaming.
Phone Indicates a phone is
currently linked to the HFL.
Signal Strength (models without
navigation system) Indicates
the network signal strength of the
current phone call. Five bars
equals f ull signal strength.
ROAM Status Indicates your
phone is roaming.
Battery Level status Indicates
the power remaining in your
phone’s current battery charge.
Five bars equals f ull battery
strength.
HFL Mode Indicates when you
are dialing and receiving calls.
Phone Dialing Indicates the
number you entered or the
number of the incoming call.
Some phones will not send this
inf ormation to the HFL. Some phones will not send this
inf ormation to the HFL.
: :
HandsFreeL ink
Comf ort and Convenience Feat ures
Center Console Display
151
ROAM STATUS
PHONESIGNAL
STLENGTH
TM

Thevoiceof theHFLcanbesetto
male or f emale (U.S. models only).
Also, the incoming notif ication can
be set to a ring tone, a prompt, or no
notification.Your Bluetooth compatible phone
with HandsFree Prof ile must be
paired to the HFL before you can
make and receive hands-free call.
HFL does not allow you to pair
your phone if the vehicle is
moving.
For pairing, your phone must be in
its Discovery mode.
Up to six phones can be paired to
the HFL.
The f ollowing procedure works f or
most phones. If you cannot pair
your phone to the HFL with this
procedure, ref er to your phone’s
operating manual, or talk to your
phone retailer.
Press and release the Talk button.
If you say ‘‘Yes’’ af ter the beep, the
HFL response is, ‘‘Would you like
a ring tone or a prompt?’’ If you
say ‘‘No’’ af ter the beep, the HFL
returns to its main menu. Saying
‘‘No’’ will result in no ring tone or
prompt playback during an
incoming call. The audio system
will still mute, and a message will
be displayed.
Press and release the Talk button.
Af ter the beep, say ‘‘Ring tone’’ or
‘‘Prompt.’’ If you choose ‘‘Ring
tone’’ you will hear a ring tone
through the audio speakers to
announce an incoming call. If you
choose ‘‘Prompt,’’ you will hear
this message to announce an
incoming call: ‘‘You have an
incoming call.’’
During the pairing process, turn
of f any previously paired phones
bef ore pairing a new phone.
Press and release the Talk button.
Af ter the beep, say ‘‘Male’’ or
‘‘Female,’’ depending on the
system voice you want. The HFL
response is, ‘‘Male (Female)
prompts have been selected.
Would you like an audible
notif ication of an incoming call?’’ Press and release the Talk button.
Af ter the beep, say ‘‘Setup.’’ The
HFL response is ‘‘Would you like
male or f emale prompts?’’ Press and release the Talk button.
Af ter the beep, say ‘‘System.’’ The
HFL response is, ‘‘System options
are setup and clear.’’
2. 1. 4.
5.
3.
To set up the system, do this:
Setting Up the System Pairing Your Phone
HandsFreeL ink
Comf ort and Convenience Feat ures154
NOTE:
TM

With your phone on and the
ignition in the ACCESSORY (I) or
ON (II) position, press and release
the Talk button. After the beep,
say ‘‘Phone set up.’’ The HFL
response is ‘‘Phone set up options
are status, pair, edit, delete, and
list.’’
Press and release the Talk button.
Af ter the beep, say ‘‘Pair.’’ The
HFL response is ‘‘The pairing
process requires operation of your
mobile phone. For saf ety, only
perf orm this f unction while the
vehicle is stopped. State a f our-
digit code f or pairing. Note this
code. It will be requested by the
phone.’’
Press and release the Talk button.
Af ter the beep, say the f our-digit
code you want to use. For example,
say‘‘1,2,3,4.’’TheHFLresponse
is,‘‘1,2,3,4.Isthiscorrect?’’Press and release the Talk button.
Af ter the beep, say ‘‘Enter’’. The
HFL response is ‘‘Searching f or a
Bluetooth phone.’’
Steps 5 and 6 show a
common way to get your phone into
its Discovery mode. If these steps do
not work on your phone, ref er to the
phone’s operating manual.
Follow the prompts on your phone
to get it into its Search mode. The
phone will search f or the HFL.
When it comes up, select
HandsFreeLink f rom the list of
options displayed on your phone.
When asked by the phone, enter
the four-digit code from step 3 into
your phone. The HFL response is
‘‘A new phone has been f ound.
What would you like to name this
phone?’’ Press and release the Talk button.
After the beep, say the name you
want to use. For example, say
‘‘Eric’s phone.’’ The HFL response
is ‘‘Eric’s phone has been
successf ully paired. Returning to
the main menu.’’
If you want to pair another phone,
repeat steps 1 through 7.
1.
4.
5.
6.7.
2.
3. 8.
CONT INUED
HandsFreeL ink
Comf ort and Convenience Feat ures155
NOTE:
TM

Help assure your vehicle’s f uture
reliability and perf ormance by paying
extra attention to how you drive
during the f irst 600 miles (1,000 km).
During this period:Avoid full-throttle starts and rapid
acceleration.
Avoidhardbrakingforthefirst
200 miles (300 km).
Do not change the oil until the
multi-inf ormation display indicates
it is needed.
Youshouldfollowthesesame
recommendations with an
overhauled or exchanged engine, or
when the brakes are relined.
Your Acura is designed to operate on
unleaded gasoline with a pump
octane number of 91 or higher.
Useof aloweroctanegasolinecan
cause occasional metallic knocking
noises in the engine and will result in decreased engine perf ormance.
You may hear a knocking noise from
the engine if you drive the vehicle at
low engine speed (below about 1,000
rpm) in a higher gear. To stop this,
raise engine speed by shif ting to a
lower gear.
We recommend gasolines containing
detergent additives that help prevent
f uel system and engine deposits. In
addition, in order to maintain good
perf ormance, f uel economy, and
emissions control, we strongly
recommend, in areas where it is
available, the use of gasoline that
does NOT contain manganese-based
f uel additives such as MMT.
Use of gasoline with these additives
may adversely af f ect perf ormance,
and cause the Malfunction Indicator
Lamp on your instrument panel to
come on. If this happens, contactyour authorized Acura dealer f or
service.
For f urther important f uel-related
inf ormation, please ref er to your
Quick Start Guide.
Some gasoline today is blended with
oxygenates such as ethanol or
MTBE. Your vehicle is designed to
operate on oxygenated gasoline
containing up to 10 percent ethanol
by volume and up to 15 percent
MTBE by volume. Do not use
gasoline containing methanol.
If you notice any undesirable
operating symptoms, try another
service station or switch to another
brand of gasoline.
On TL with manual transmission
Break-in Period, Gasoline T ype
Break-in Period
Gasoline Type
Bef ore Driving164

Always maintain your vehicle
according to the maintenance
messages given by the multi-
inf ormation display. Seeon page
.
an underinf lated tire
causes more ‘‘rolling resistance,’’
which uses f uel.
The build-up of snow or mud on
your vehicle’s underside adds
weight and rolling resistance.
Frequent cleaning helps your f uel
mileage and reduces the chance of
corrosion.
Drive moderately. Rapid
acceleration, abrupt cornering,
and hard braking use more f uel.
Always drive in the highest gear
possible. Try to maintain a constant speed.
Everytimeyouslowdownand
speed up, your vehicle uses extra
fuel.Usethecruisecontrolwhen
appropriate.
Combine several short trips into
one.
The air conditioning puts an extra
load on the engine which makes it
usemorefuel.Usethefresh-air
ventilation when possible.
198
For example,
Fuel Economy
Improving Fuel Economy
Owner’s
Maintenance Checks
Bef ore Driving168

µµ When you accelerate away f rom a
stop, the transmission will start in
first gear and then automatically
upshif t to second gear. You have to
manually upshif t between second
and f if th gears. Make sure you
upshif t bef ore the engine speed
reaches the tachometer’s red zone.
The transmission remains in the
selected gear (5, 4, 3). There is no
automatic downshif t when you push
the accelerator pedal to the floor.
When you move the
shif t lever to this position, the
transmission shifts to the lowest
gear that can be selected without
exceeding the engine redline. At
normal speeds, it selects third gear.
As the vehicle slows, it selects
second gear at about 53 mph
(85 km/h), and f irst gear at about 28
mph (45 km/h). Accelerating in f irst
gear, the transmission upshif ts to
second gear at about 37 mph
(59 km/h). You must move the shif t
lever to D f or the transmission to
upshif t to third gear.
In Sequential SportShif t mode, each
time you push f orward on the shif t
lever, the transmission shifts to a
higher gear. Pull back on the lever to
downshif t. The number of the gear
selected is displayed on the
instrument panel.
With
the shif t lever in ‘‘D’’ position, you
can select the Sequential SportShif t
Mode to shif t gears much like a
manual transmission, but without a
clutch pedal.
To enter the Sequential SportShif t
Mode, move the shif t lever f urther to
the driver’s side. To return to ‘‘D’’,
move the shift lever to the passenger’s side.
When you move the shif t lever f rom
‘‘D’’ to the Sequential SportShift
mode, the display shows the selected
gear.
CONT INUED
Automatic Transmission
Driving
Low (L)
Sequent ial Sport Shif t Mode
183
Down shift
SELECTED GEAR

à
à à
àà
à
à
à
The transmission may automatically
downshif t f rom the higher gear to
the lower gear under these
conditions:
Downshif ting gives you more power
when climbing, and provides engine
braking when going down a steep hill.
The transmission will also shif t
automatically as the vehicle comes to
a complete stop. It will downshif t to
f irst gear when the vehicle speed is
under 9 mph (15 km/h).
If you try to manually downshif t at a
speed that would cause the engine to
exceed the redline in a lower gear,
the transmission will not downshif t.If the vehicle speed slows to below
the redline of the selected lower gear
position while the indicator is
f lashing, the transmission will
downshif t and the display will show
the selected lower gear.
The table shows the speed ranges
f or upshif ting and downshif ting.
To shift from 43
54
To shift from
43
54 To shift from
12
23
34
45
Thegearindicatorwillflashthe
numberof thelowergearseveral
times, then return to the higher gear.
Speed range
over 0 mph
(0 km/h)
over 9 mph
(15 km/h)
over 18 mph
(29 km/h)
over 37 mph
(60 km/h)
Speed range
under 18 mph
(29 km/h)
under 38 mph
(60 km/h)
Speed range
under 41 mph
(65 km/h)
under 47 mph
(75 km/h)
Driving uphill Driving on level roads and downhill
Automatic Transmission
Driving184