reset Acura TL 2004 Owner's Manual

The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages. Some of
the messages help you operate your
vehiclemorecomfortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.
Here is a list of the messages you
can see. The f ollowing pages give
you more inf ormation on these
messages.Driver 1 or 2 Detected
Door and Trunk Open
Fasten Seat Belt
Release Parking Brake
Check Fuel Cap
Odometer
Trip Meter
Outside Temperature
Engine Oil Lif e Maintenance Messages
Trip Computer
Keyless Memory Settings
HandsFree Link
Language Selection (Canada only)
With the multi-information display
and the two buttons next to it, you
can also customize these vehicle
control settings to your liking. Auto door lock conditions
Auto door unlock conditions
Whenever unlocking (driver’s
door, or all doors)
Keyless lock acknowledgment
conditions
Security relock timer
Headlight auto of f timer
Interior light dimming time
To customize these control settings,
see page .
Low Windshield Washer Fluid
Level (Canada only) 66
Multi-Inf ormation Display
Inst rument s and Cont rols58
SELECT/
RESET
BUTTON
INFO
BUTTON
TM
TM

The odometer shows the total dis-
tance your vehicle has been driven.
It measures miles in U.S. models and
kilometers in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated.This meter show the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. There
are two trip meters: Trip A and Trip
B. When you first turn the ignition
switch to ON (II), Trip A is displayed.
Switch between Trip A and Trip B by
pressing the Select/Reset button
repeatedly. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
If the f luid level in the windshield
washer reservoir gets low, the multi-
inf ormation display shows the above
message.
On Canadian models
Multi-Inf ormation Display
L ow Windshield Washer Fluid
Level
Odometer
T rip Meter
Inst rument s and Cont rols62
ODOMETER
TRIP METER

To reset a trip meter, display it, then
press and hold the Select/Reset
button until the number resets to
‘‘0.0’’.
Both trip meters will reset if the
vehicle’s battery goes dead or is
disconnected.This shows the outside Fahrenheit
temperature in U.S. models, and
Centigrade temperature in Canadian
models.
In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace. The temperature sensor is in the
f ront bumper. The temperature
reading can be affected by heat
ref lection f rom the road surf ace,
engine heat, and the exhaust f rom
surrounding traf f ic. This can cause
an incorrect temperature reading
when your speed is under
19 mph (30 km/h). When you start
your trip, the sensor is not f ully
acclimatized, theref ore it may take
several minutes until the proper
temperature is displayed.
Multi-Inf ormation Display
Inst rument s and Cont rols
Outside Temperature
63
SELECT/
RESET
BUTTON

This shows the remaining lif e of the
engine oil. It shows 100% af ter the
engine oil is replaced and the display
is reset. The engine oil lif e is
calculated based on engine operating
conditions and accumulated engine
revolutions.When the engine oil lif e reaches 15
percent, the display shows
‘‘SERVICE DUE SOON’’ and the
code f or the maintenance items to be
perf ormed.
When the engine oil lif e reaches 5
percent, the display shows
‘‘SERVICE DUE NOW’’ along with
the same maintenance items.Have your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display af ter completing the service.
If you do not perf orm the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil lif e becomes 0 percent.
These messages appear on the multi-
inf ormation display each time you
turn the ignition switch to ON (II).
For details on engine oil lif e and
maintenance messages, ref er to page
.
Also ref er to page f or important
maintenance saf ety precautions. 195
194
Multi-Inf ormation Display
Inst rument s and Cont rols
Engine Oil L if e Maintenance Messages
64

¼
When the multi-information display
is in the trip computer mode, press
the Select/Reset button. The display
changesasshownabove. Themessagesinthisdisplay
indicate:
When the display shows the initial
screen of the trip computer, press
the side of the INFO button to
display ‘‘MILES TO EMPTY’’. This
is the estimated distance you can
travelonthefuelremaininginthe
tank. This distance is estimated from
the f uel economy you received over
the last several miles, so it will vary
withchangesinspeed,traffic,etc.
AVG MPG: Average vehicle speed
AVG MPH: Average f uel economy
DIST: Distance traveled
TIME: Time traveled
To reset the values in the trip
computer, press Select/Reset button,
and hold it f or about 1 second.
Multi-Inf ormation Display
Inst rument s and Cont rols
Trip Computer
65

¼
You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize: Auto door lock conditions
Auto door unlock conditions
Security relock timer Keyless lock acknowledgment
conditions
Headlight auto of f timer
Interior light dimming time While ‘‘Keyless Memory Settings’’ is
displayed, press the Select/Reset
button. The display will change to
the screen shown above. Select the menu item you want
(‘‘CHG SETTINGS’’, ‘‘DEFAULT
ALL’’ or ‘‘EXIT’’) by moving the
pointer ‘‘ ’’ with the INFO button.
Af ter selecting a menu item, enter
your selection by pressing the
Select/Reset button.
To exit this mode without changing
the current settings, select ‘‘EXIT’’
and press the Select/Reset button.
The display will move to the next
mode.
If you want to change the settings,
select ‘‘CHG SETTINGS’’, and press
the Select/Reset button. The display
will change to the screen shown in
the middle column of this page.
Multi-Inf ormation Display
Inst rument s and Cont rols
K eyless Memory Settings
66
TM

»¼¼
¼
If you want the settings as they were
when the vehicle lef t the f actory,
select ‘‘DEFAULT ALL’’ and press
the Select/Reset button. The display
will change to the screen shown
above. Press the Select/Reset button
to select ‘‘OK’’ or press the or
side of the INFO button to cancel. The f irst Keyless Memory Setting is
Auto Door Lock conditions. Select
the desired condition by moving the
pointer with the side of the INFO
button. On the display will be next
to the current setting.Herearethethreepossiblesettings:
OFF: The auto door lock is
deactivated all the time.
SHIFTFROMP:Thedoorswilllock
whenever you move the shif t lever
out of P. (Models with automatic
transmission.)
10 MPH: The doors will lock when
the vehicle speed reaches 10 mph.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols67

¼¼
The next setting menu is ‘‘KEYLESS
LOCK ACKNOWLEDGMENT’’.
If you do not want the beeper to
sound, select ‘‘BEEP OFF’’ and enter
your selection by moving the pointer
with the side of the INFO button. The next setting menu is
‘‘SECURITY RELOCK TIMER’’.
If you unlock the doors with the
remote transmitter, but do not open
any of the doors within 30 seconds,
the doors automatically relock and
the security system sets.
The headlights, parking lights,
taillights and licence plate light turn
of f af ter the selected time when you
remove the key from the ignition
switch and close the driver’s door.
You can change this relock time
f rom 30 seconds to 60 or 90 seconds.
Select the desired relock time by
moving the pointer with the side
of the INFO button. The last two setting menus are
‘‘HEADLIGHT AUTO OFF TIMER’’
and ‘‘INTERIOR LIGHT DIMMING
TIME’’.
Select the time (‘‘0S, 15S, 30S or 60
S’’) and enter your selection by
pressing the Select/Reset button.
When you push the LOCK button a
second time within 5 seconds after
you lock the doors with the remote
transmitter, a beep will sound to
verify that doors are locked and the
security system has set.
Multi-Inf ormation Display
Inst rument s and Cont rols69

¼
On Canadian models only
You can switch the language of the
multi-inf ormation display between
French and English.
When the multi-information display
is in the ‘‘LANGUAGE
SELECTION’’ mode (screen shown
above), press the Select/Reset
button. The display will change to
the selection screen.Select the desired language, French
or English, by pressing the side of
the INFO button, and enter your
selection by pressing the Select/
Reset button.
Multi-Inf ormation Display
Inst rument s and Cont rols
Language Selection
71

If your vehicle’s battery is
disconnected or goes dead, or a f ront
window f use is removed, the AUTO
f unction could be disabled. If the
AUTO f unction is disabled, do the
f ollowing:The power window system has a key-
of f delay f unction. The windows will
stilloperateforupto10minutes
after you turn off the ignition.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch to ON (II) again
bef ore you can operate the windows.
Start the engine. Push down on
the f ront window switch until the
window is f ully open.
Pull back on the f ront window
switch to close the window
completely, then hold the switch
f or a second or two more.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by an Acura dealer. 1.
2.
Power Windows
Inst rument s and Cont rols99