Acura TL 2006 Owner's Manual

Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.Insert the fastener into the hole on
the side of the trunk lining, and
push in the head of the f astener.
Screw the cargo net hook into the
f ender.
Determine which back-up light
is out (lef t or right), then open
the trunk. Popupthepininthecenterof
the lef t or right corner f astener
with a small screwdriver, and
remove the fastener.
Remove the lef t side
f astener the same way.
Pull out the outside edge of the
rubber stop, then push the stop
outward, and pull it to remove it.
Remove the
screw f rom the trunk lid inner
handle, and remove the handle
trim.
Pull back the corner of the
trunk lid lining.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
3.
4.
5.
6. 7.
b.
c.
d.
1a. e.
Lef t side
only:
Right side only:
Replacing the Back-up L ight Bulb
(in T runk L id)
Lights
230
RIGHT STOP
CORNER
FASTENER
CORNER
FASTENER LEFT STOP
TRUNK LID
INNER
HANDLE
LEFT SIDE FASTENER

Test the lights to make sure the
new bulb is working.
Reinstall the trunk lid lining. Make
sure it is installed under the edge
of the trunk seal. Insert the socket into the light
assembly. Turn it clockwise to
lock it in place.
Install all removed parts.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms. If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water, or isopropyl alcohol.
2.
3. 4.
5.
6.
7.
Cleaning the Seat Belts
Lights, Cleaning the Seat Belts
Maint enance
231
LOOP

Check the condition of the wiper
blades at least every 6 months.
Replace them if you f ind signs of
cracking in the rubber, areas that are
getting hard, or if they leave streaks
and unwiped areas when used.Raise the wiper arm of f the
windshield.
If you use non-Acura f loor mats,
make sure they f it properly and that
theycanbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats. If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.
The driver’s and right rear
passenger’s f loor mats that came
with your vehicle hook over the f loor
mat anchors. This keeps the f loor
mats f rom sliding f orward and
possibly interf ering with the pedals
(driver’s floor mat) or with the seat
weight sensors (right rear f loor mat). 1.
Floor Mats, Wiper Blades
Floor Mats
Wiper Blades
232
FLOOR MAT ANCHORSDo not open the hood when the wiper
arms are raised, or you will damage the
hood and wiper arms.

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.
Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
2.
3.5.
4. 6.
7.
Wiper Blades
Maint enance
233
LOCK TAB
BLADE REINFORCEMENTBLADE

´However, these tires are not suitable
f or driving on snow or ice, so all-
season or winter tires must be
installed f or winter driving
conditions.
See page f or winter driving
conditions.
Keeping the tires properly inf lated
provides the best combination of
handling, tread lif e, and riding
comf ort.
Underinf lated tires wear unevenly,
adversely affect handling and fuel
economy, and are more likely to
fail from being overheated.
Overinf lated tires can make your
vehicleridemoreharshly,are
more prone to damage f rom road
hazards, and wear unevenly.
Your vehicle is equipped with high
perf ormance all-season tires
(marked All Season or M S on the
sidewalls). These tires provide
excellent handling and braking
perf ormance in most driving
situations.
Your vehicle is equipped with high
perf ormance summer tires. These
tires have a high-traction compound
and tread pattern to provide superior
acceleration, cornering, and stopping
under most driving conditions.
To saf ely operate your vehicle, your
tires must be the proper type and
size, in good condition with adequate
tread, and correctly inf lated.
The f ollowing pages give more
detailed inf ormation about your tires,
how and when to inspect your tires
for damage and wear, and what to do
when your tires need to be replaced.
239
Manual Transmission Models with
Summer Tires
All Models Except Manual Transmission
Models with Summer Tires
Inf lation Guidelines
Tire Types
Tires
234
Using tires that are excessively
worn or improperly inflated can
cause a crash in which you can
be seriously hurt or killed.
Follow all instructions in this
owner’s manual regarding tire
inflation and maintenance.

The following chart shows the
recommended cold tire pressures f or
most normal driving conditions and
speed.Thecompactsparetirepressureis:
We strongly recommend that you
not drive f aster than posted speed
limits and conditions allow. If you
decide it is saf e to drive at high
speeds (over 118 mph or 190 km/h),
be sure to adjust the cold tire
pressuresasshownbelow.If youdo
not adjust the tire pressure,
excessive heat can build up and
cause sudden tire f ailure.
Use a gauge to measure the air
pressure in each tire at least once a
month. Even tires that are in good
condition may lose 1 to 2 psi (10 to
20 kPa, 0.1 to 0.2 kgf /cm ) per
month. We recommend that you visually
check your tires every day. If you
think a tire might be low, check it
immediately with a tire gauge. The tire pressure monitoring system
(TPMS) will warn you when tire
pressure is low. See page f or
inf ormation on the TPMS.
Remember to check the spare tire at
thesametimeyoucheckallthe
other tires. 204
Tire Size Cold Tire Pressure for
Normal Driving
Tire Size Cold Tire Pressure for Normal Driving Tire Size Cold Tire Pressure for
High Speed DrivingAutomatic Transmission Models
Manual Transmission Models All Models
CONT INUED
Recommended T ire Pressures f orNormal Driving
Recommended T ire Pressures f orHigh Speed Driving
Tires
Maint enance
235
60 psi (420 kPa , 4.2 kgf/cm)
P235/45R17 93W
35 psi (240 kPa ,2.4 kgf/cm
)
32 psi (220 kPa , 2.2 kgf/cm
)
P235/45R17 93W
235/45R17 93W P235/45R17 93W
235/45R17 93W 39 psi (270 kPa ,
2.7 kgf/cm
)
35 psi (240 kPa , 2.4 kgf/cm
)
32 psi (220 kPa ,
2.2 kgf/cm
)
33 psi (230 kPa ,
2.3 kgf/cm
)
Front:
Rear:
Front:
Rear:
Front:
Rear:

When you return to normal speed
driving, be sure to readjust the tire
pressure f or normal driving. You
should wait until the tires are cold
bef ore adjusting the tire pressure.
For convenience, the recommended
tire sizes and cold tire pressures are
on a label on the driver’s doorjamb.
For additional technical inf ormation,
see page .Every time you check inf lation, you
should also examine the tires for
damage, f oreign objects, and wear.
Youshouldlookfor:
Bumps or bulges in the tread or
side of the tire. Replace the tire if
youfindeitherof theseconditions.
Cuts, splits, or cracks in the side
of the tire. Replace the tire if you
can see f abric or cord.
Excessive tread wear.
Check the pressure in the tires when
thetiresarecold.Thismeansthe
vehicle has been parked f or at least
three hours. If you have to drive the
vehiclebeforecheckingtirepressure,
the tires can still be considered
‘‘cold’’ if you drive less than 1 mile
(1.6 km). Add or release air, if
needed, to match the recommended
cold tire pressure. If you check air pressure when the
tires are hot [driven f or several miles
(kilometers)], you will see readings 4
to6psi(30to40kPa,0.3to0.4
kgf /cm ) higher than the cold
readings. This is normal. Do not let
air out to match the recommended
cold air pressure. The tire will be
underinf lated.
Youshoulduseyourowntire
pressure gauge whenever you check
your tire pressures. This will make it
easier f or you to tell if a pressure
loss is due to a tire problem and not
due to a variation between gauges.
While tubeless tires have some
ability to self -seal if they are
punctured, you should look closely
for punctures if a tire starts losing
pressure.
273 Tire Inspection
Tires
236

Your vehicle’s tires have wear
indicators molded into the tread.
When the tread wears down to that
point, you will see a 1/2 inch (12.7
mm) wide band running across the
tread. This shows there is less than
1/16 inch (1.6 mm) of tread lef t on
the tire. A tire that is this worn gives
very little traction on wet roads. You
should replace the tire if you can see
the tread wear indicator in three or
more places around the tire.In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
Have your dealer check the tires if
you f eel a consistent vibration while
driving. A tire should always be
rebalanced if it is removed f rom the
wheel. When you have new tires
installed, make sure they are
balanced. This increases riding
comf ort and tire lif e. For best results,
have the installer perform a dynamic
balance.
To help increase tire lif e and
distribute wear more evenly, rotate
the tires every 7,500 miles (12,000
km). Move the tires to the positions
showninthecharteachtimethey
are rotated. If you purchase
directional tires, rotate only f ront-to-
back.
T ire Maintenance
T ire Rotation
Tires
Maint enance
237
INDICATOR LOCATION MARKS
TREAD WEAR INDICATOR Front
Front
(Front Directional
Tires and Wheels)
(Front Non-directional
Tires and Wheels)
Improper wheel weights can damage
your vehicle’s aluminum wheels. Use
only Acura wheel weights f or balancing.

Replace your tires with radial tires of
the same size, load range, speed
rating and maximum cold tire
pressure rating (as shown on the
tire’s side wall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
anti-lock brake and the vehicle
stability assist systems to work
inconsistently.Wheels:
Tires:
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
If you ever replace a wheel, make
sure that the wheel’s specif ications
match those of the original wheels.
Also be sure you use only TPMS
specif ic wheels. If you do not, the
tire pressure monitoring system will
notworkonthattire.
Replacement wheels are available at
your Acura dealer.
(All season tire)
(Summer tire)
Replacing T ires and Wheels
Wheel and T ire Specif ications
Tires
238
17x8.0JJ
P235/45R17 93W
235/45R17 93W Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.

´When installing cables, f ollow the
manuf acturer’s instructions, and
mount them as tight as you can.
Make sure they are not contacting
the brake lines or suspension. Drive
slowly with them installed. If you
hear them coming into contact with
the body or chassis, stop and
investigate. Remove them as soon as
you begin driving on cleared roads.
If you mount snow tires on your
vehicle, make sure they are radial
tires of the same size and load range
as original tires. Mount snow tires on
all f our wheels. The traction
provided by snow tires on dry roads
maybelowerthanyouroriginaltires.
Check with the tire dealer f or
maximum speed recommendations.
Because your vehicle has limited tire
clearance, mount only SAE Class ‘‘S’’
cable-type traction devices, with
rubber chain tensioners on the f ront
tires. Use traction devices only when
required by driving conditions or
local laws. Make sure they are the
correct size f or your tires. Metal link-
type ‘‘chains’’ should not be used.
See page f or DOT tire quality
grading inf ormation, and page
f or tire size inf ormation.
Tires marked ‘‘M S’’ or ‘‘All
Season’’ on the sidewall have an all-
weather tread design suitable for
most winter driving conditions.
For the best perf ormance in snowy
or icy conditions, you should install
snow tires or tire chains. They may
be required by local laws under
certain conditions.
If your vehicle is equipped with
summer tires, be aware that these
tires are not designed f or winter
driving conditions. For more
inf ormation, consult your dealer. 273
274
Tires
Snow T ires
Tire Chains
Summer T ires Winter Driving
Maint enance
239
Traction devices that are the wrong
size or improperly installed can
damage your vehicle’s brake lines,
suspension, body, and wheels. Stop
driving if they are hitting any part of
the vehicle.