ignition Acura TL 2006 Owner's Guide

When you f inish, move the
selector switch to the center (off)
position. This turns of f the
adjustment switch to keep your
settings.The outside mirrors are heated to
remove fog and frost. With the
ignition switch in the ON (II)
position, turn on the heaters by
pressing the button. The indicator in
the button comes on as a reminder.
Press the button again to turn the
heaters off.
Depending on the position of the
selector switch, the lef t or right side
mirror will pivot downward slightly
when you shif t the transmission into
reverse. In the lef t position, the lef t
mirror pivots. In the right position,
the right mirror pivots. This gives
you a better view of that side of the
vehicle while parallel parking. The
mirror returns to its original position
when you take the transmission out
of reverse. To turn this f eature of f ,
leave the switch in the center
position.
Outside mirror positions can be
stored in the driving position
memory system (see page ). 3.
103
Mirrors
Power Mirror Heaters
102
HEATED MIRROR BUTTON

Two seat and outside mirror
positionscanbestoredinseparate
memories. You select a memorized
position by pushing the appropriate
button or using the appropriate
remote transmitter (Driver 1 or
Driver 2).Adjust the outside mirrors f or best
visibility (see page ). Adjust the seat to a comfortable
position (see page ). Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position in the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Store a driving position only when
the vehicle is parked.
Your vehicle has a memory feature
f or the driver’s seat and outside
mirror positions.
Press and release the MEMO
button on the driver’s door. You
will hear a beep. Immediately
press and hold one of the memory
buttons (1 or 2) until you hear two
beeps. The indicator in the
memory button will come on. The
current positions of the driver’s
seat and outside mirrors are now
stored.
3.
1.
2.
98
101
CONT INUED
Driving Position Memory System
Storing a Driving Position in
Memory
Inst rument s and Cont rols
103
MEMO BUTTON
MEMORY BUTTONS

Follow these precautions whenever
you use the seat heaters:
Both f ront seats are equipped with
seat heaters. The passenger seat
only has heaters in the seat bottom
because of the side airbag system.
The ignition switch must be in the
ON (II) position to use them. Push
theHIsideof theswitchtorapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
pushtheLOsideof theswitch.This
will keep the seat warm. In HI, the heater turns of f when the
seat gets warm, and turns back on
after the seat temperature drops.
In LO, the heater runs continuously.
It does not cycle with temperature
changes.
Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
Seat Heaters
106
SEAT HEATER SWITCHES

Turn the ignition switch to the ON
(II) position to raise or lower any
window. To open a window, push the
switchdownandholdit.Releasethe
switch when you want the window to
stop. Pull back on the switch and
hold it to close the window.The windows will operate f or up to
10 minutes af ter you turn of f the
ignition switch. Opening either f ront
door cancels this f unction.
If the MAIN switch is off, the
passenger’s windows cannot be
raised or lowered. Keep the MAIN
switch of f when you have children in
the vehicle so they do not injure
themselves by operating the
windows unintentionally.
CONT INUED
Power Windows
Inst rument s and Cont rols
107
DRIVER’S WINDOW
SWITCH
MAIN
SWITCH
Closing a power window on
someone’s hands or fingers can
cause serious injury.
Make sure your passengers are
away from the windows before
closing them.

You can use the remote transmitter
or the key to operate the moonroof
f rom the outside. Ref er to pagef or details.
The moonroof has a key-of f delay.
You can still open and close the
moonroof f or up to 10 minutes af ter
you turn of f the ignition switch. The
key-of f delay cancels as soon as you
open either f ront door. You must
then turn the ignition switch to the
ON (II) position f or the moonroof to
operate.
107
Operating the Moonroof with the
Remote Transmitter or the Key
Moonroof
Inst rument s and Cont rols
111
If you try to open the moonroof in
below-f reezing temperatures, or when
it is covered with snow or ice, you can
damage the moonroof panel or its
motor.

To apply the parking brake, pull the
lever up f ully. To release it, pull up
slightly, push the button, and lower
the lever. The parking brake
indicator on the instrument panel
should go out when the parking
brake is f ully released (see page ).
The clock displays the time with the
ignition switch in the ON (II)
position. If your vehicle’s battery is
disconnected or goes dead, you will
need to reset the clock.
For example: 1:06 will reset to 1:00
1:52 will reset to 2:00
The clock is set automatically. Change the hour by pressing and
holding the H button until the
numbers advance to the desired time.
Change the minutes by pressing and
holding the M button until the
numbers advance to the desired time.
You can quickly set the time to the
nearest hour. If the displayed time is
bef ore the half hour, press the R
button to set the clock back to the
previous hour. If the displayed time
is af ter the half hour, the clock sets
f orward to the beginning of the next
hour.
60On models without Navigation SystemOn models with Navigation System
Clock Parking Brake
Clock, Parking Brake
112
Driving the vehicle with the parking
brake applied can damage the rear
brakes and axles.

µ´µ
µ
µ The SEEK f unction
searches up and down from the
current f requency to f ind a station
with a strong signal. To activate it,
press the or SEEK button, then
release it.
The SCAN function
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button, or
touch the SCAN icon (models with
navigation system), then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
If you do nothing, the system will
scan f or the next strong station and
play it f or 5 seconds. When it plays a
station you want to listen to, press
the SCAN button again.
The band and f requency that the
radio was last tuned to is displayed.
To change bands, press the AM/FM
button (AM or FM button on
Canadian model). On the FM band,
ST will be displayed if the station is
broadcasting in stereo. Stereo
reproduction on AM is not available.
You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and .
Use the TUNE knob to
tune the radio to a desired f requency.
Turn the knob right to tune to a
higher f requency, or lef t to tune to a
lower f requency.
The ignition switch must be in the
ACCESSORY (I) or ON (II) position.
Turn the system on by pushing the
VOL/PWR knob or the AM/FM
button (AM or FM button on
Canadian model). Adjust the volume
by turning the same knob. The audio system f or your vehicle
can also be operated using the voice
control system. See Navigation
section in your Quick Start Guide f or
an overview of this system and the
Navigation System manual f or
complete details.
Only on models equipped with
Navigation System
Playing the AM/FM Radio
SEEK
SCAN
To Select a Station
TUNE,SEEK,SCAN, AUTO SELECT
TUNE
To Play the AM/FM Radio Voice Control System
128

µµ
ÓÓµ
µ´
Your vehicle is capable of receiving
XM
Satellite Radio anywhere in the
United States, except Hawaii and
Alaska.
XM
is a registered trade mark of
XM Satellite Radio, Inc. To switch between the
channel mode and the category
mode,pressandholdtheDISP/
MODE button until the mode
changes. On models with navigation
system, touch the MODE icon on the
audio display.
In the channel mode, you can select
all of the available channels. In the
category mode, such as Jazz, Rock,
Classical, etc., you can select all of
the channels within that category.
Each time you press and release the
DISP/MODE button, the display
changes in the f ollowing sequence:
channel name, channel number,
category, artist name, and music title.
You may experience periods when
XM Radio does not transmit the
artist’s name and song title
inf ormation. If this happens, there is
nothing wrong with your system. On models with navigation system,
push the AUDIO button to display
XM inf ormation on the screen.
Turn the TUNE knob lef t
or right to select channels. In the
category mode, you can only select
channels within that category.
In the
category mode, press either button
to select another category.
XM radio receives signals f rom two
satellites to produce clear, high-
quality digital reception. It of f ers
many channels in several categories.
Along with a large selection of
dif f erent types of music, XM radio
allows you to view channel and
category selections in the display.
To listen to XM radio, turn the
ignition switch to the ACCESSORY
(I) or ON (II) position. Push the
PWR/VOL knob to turn on the audio
system, and press the
button. Adjust the volume
by turning the PWR/VOL knob. The
last channel you listened to will show
in the display.
Playing the XMSatellite Radio (U.S. Models)
MODE
TUNE
CATEGORY ( or )
Operating the Satellite Radio
Features
135

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the north side of a
large commercial truck on an
east/west road.
Driving in tunnels.
Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you.
Driving on the lower level of a
multi-tiered road.
Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you. If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
PWR/VOL knob to turn on the audio
system and press the button.
A variety of music types and styles
will play.
If you decide to purchase XM
satellite radio service, contact XM
Radio at
, or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, turn the TUNE knob until ‘‘0’’ appears in the display.
Your I.D. will appear in the display.
After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.
Driving on the north side of an
east/west mountain road.
While waiting f or activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated, you should
be able to listen to XM radio
broadcasts. XM Radio will continue
to send an activation signal to your
vehicle for at least 12 hours from the
activation request. If the service has
not been activated after 36 hours,
contact XM Radio.
There may be other geographic
situations that could af f ect XM radio
reception.As required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
www.xmradio.com
Receiving Satellite Radio Service
Playing the XMSatellite Radio (U.S. Models)
139

The disc changer can play these disc
formats:CD
CD-R
DVD-A
DTS
DVD-A discs not meeting DVD
verification standards may not be
playable.
The changer cannot play DVD-V,
DVD-R/RW, MP3, or WMA f ormats.
Some CD-DA and CD-ROM mixed
discs are not playable.
‘‘DTS’’ and ‘‘DTS Digital Surround’’
are registered trademarks of Digital
Theater System, Inc. To load multiple discs in one
operation:
Your vehicle’s audio system has an
in-dash disc changer that holds up to
six discs. You operate this disc
changer with the same controls used
f or the radio. To operate the disc
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position.
With the ignition switch in the
ACCESSORY (I) or ON (II)
position, press and hold the LOAD
button until you hear a beep and
see ‘‘LOAD’’ in the display, then
release the button.
Insert a disc into the slot. Insert it
only about half way; the drive will
pull it in the rest of the way.
When the ‘‘DISC LOAD’’ appears
in the display, insert the next disc
into the slot.
Repeat this until all six positions
are loaded. The system will thenbegin playing the last disc loaded.
If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 15 seconds, stop the load
operation, and begin playing the last
disc loaded.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded. The disc number f or an empty
position is highlighted and the
green load indicator comes on.
When you see ‘‘LOAD’’ in the
display, insert the disc into the slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way. Press and release the LOAD
button.
To load a single disc:
1.
2.
3.
4. 1.
2.
L oading Discs in the Changer
Playing Discs
141
TM
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.