lock Acura TL 2006 Repair Manual

Pour the f luid slowly and caref ully so
you do not spill. Clean up any spill
immediately; it could damage
components in the engine
compartment.
Check the level on the side of the
reservoir when the engine is cold,
and the engine compartment right-
side cover is of f (see page ). The
f luid should be between the UPPER
LEVEL and LOWER LEVEL. If not,
add power steering f luid to the
UPPER LEVEL mark. Always use Honda Power Steering
Fluid. You may use another power
steering f luid as an emergency
replacement, but have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
217
Power Steering Fluid
226
UPPER LEVEL
LOWER LEVEL
Turning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.

Insert the new bulb into the hole,
and turn it one-quarter turn clock-
wise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
(Driver’s side)
Install the upper part of the air
intake duct.
(Driver’s side)
Install the engine compartment
corner cover, and secure it with
two fastener pins.
Install the engine compartment
side cover.
Remove the bulb by turning it one-
quarter turn counterclockwise. Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down. Start the engine. If you are
replacing a driver’s side bulb, turn
the steering wheel all the way to
theright.If youarereplacinga
passenger’s side bulb, turn the
steering wheel to the lef t. Turn of f
the engine.
4.
5.
6.
7.
8.
9.
2.
3. 1. Replacing the Front T urn Signal/
Parking L ight Bulb
Lights
228

Use a f lat-tipped screwdriver to
remove the holding clip f rom the
middle edge of the inner f ender
cover, and pull the inner f ender
cover back.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Remove the bulb f rom the socket
bypushingitinandturningit
counterclockwise until it unlocks.
Install the new bulb in the socket.
Turn it clockwise to lock it in place.
Insert the socket into the
headlight assembly. Turn it
clockwise to lock it in place.
Test the lights to make sure the
new bulb is working.
Push the inner f ender cover in
place. Install the holding clip, and
lock it in place by pushing on its
center.
Open the trunk.
Using a small screwdriver, pop up
the pin in the center of the
f astener, then remove the f astener.
Unscrew and remove the cargo
net hook f rom the f ender. Pull
back the trunk lining.
Remove the socket by turning it
one-quarter turn counterclockwise.
3. 2. 4.
5.
6.
7.
8.
1.
2.
CONT INUED
Replacing the Rear Turn Signal
Bulb (in Fenders)
Lights
Maint enance
229

Reinstall the trunk lining. Make
sure it is installed under the edge
of the trunk seal.Insert the fastener into the hole on
the side of the trunk lining, and
push in the head of the f astener.
Screw the cargo net hook into the
f ender.
Determine which back-up light
is out (lef t or right), then open
the trunk. Popupthepininthecenterof
the lef t or right corner f astener
with a small screwdriver, and
remove the fastener.
Remove the lef t side
f astener the same way.
Pull out the outside edge of the
rubber stop, then push the stop
outward, and pull it to remove it.
Remove the
screw f rom the trunk lid inner
handle, and remove the handle
trim.
Pull back the corner of the
trunk lid lining.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Testthelightstomakesurethe
new bulb is working.
3.
4.
5.
6. 7.
b.
c.
d.
1a. e.
Lef t side
only:
Right side only:
Replacing the Back-up L ight Bulb
(in T runk L id)
Lights
230
RIGHT STOP
CORNER
FASTENER
CORNER
FASTENER LEFT STOP
TRUNK LID
INNER
HANDLE
LEFT SIDE FASTENER

Test the lights to make sure the
new bulb is working.
Reinstall the trunk lid lining. Make
sure it is installed under the edge
of the trunk seal. Insert the socket into the light
assembly. Turn it clockwise to
lock it in place.
Install all removed parts.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms. If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air-dry bef ore
you use the vehicle.
Dirt build-up in the loops of the seat
belt anchors can cause the belts to
retract slowly. Wipe the insides of
the loops with a clean cloth
dampened in mild soap and warm
water, or isopropyl alcohol.
2.
3. 4.
5.
6.
7.
Cleaning the Seat Belts
Lights, Cleaning the Seat Belts
Maint enance
231
LOOP

Remove the blade f rom its holder
by grasping the tabbed end of the
blade. Pull f irmly until the tabs
come out of the holder.
Examine the new wiper blades. If
they have no plastic or metal
reinf orcement along the back
edge, remove the metal
reinf orcement strips f rom the old
wiper blade, and install them in
the slots along the edge of the new
blade.Slide the new wiper blade into the
holder until the tabs lock.
Slide the wiper blade assembly
onto the wiper arm. Make sure it
locks in place.
Lower the wiper arm down against
the windshield.
Disconnect the blade assembly
fromthewiperarmbypushingin
the lock tab. Hold the lock tab in
while you push the blade assembly
toward the base of the arm.
2.
3.5.
4. 6.
7.
Wiper Blades
Maint enance
233
LOCK TAB
BLADE REINFORCEMENTBLADE

Replace your tires with radial tires of
the same size, load range, speed
rating and maximum cold tire
pressure rating (as shown on the
tire’s side wall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
anti-lock brake and the vehicle
stability assist systems to work
inconsistently.Wheels:
Tires:
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
If you ever replace a wheel, make
sure that the wheel’s specif ications
match those of the original wheels.
Also be sure you use only TPMS
specif ic wheels. If you do not, the
tire pressure monitoring system will
notworkonthattire.
Replacement wheels are available at
your Acura dealer.
(All season tire)
(Summer tire)
Replacing T ires and Wheels
Wheel and T ire Specif ications
Tires
238
17x8.0JJ
P235/45R17 93W
235/45R17 93W Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.

If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.Fill the f uel tank.
Change the engine oil and f ilter.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry. Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and trunk seals.Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f an cycles twice).
Pref erably, do this once a month.
Leave the parking brake off. Put
the transmission in reverse
(manual) or Park (automatic).
Vehicle Storage
Maint enance
241

If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area to stop
that is far away from the traffic lanes.Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.Open the trunk. Raise the trunk
f loor by lif ting up on the back edge.
Take the tool case out of the spare
tire.
Unscrew the wing bolt and take
the spare tire out of its well.
Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park (automatic)
or reverse (manual). Apply the
parking brake.
5. 4.
3.
2. 1.
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
245
TOOL CASE
JACK
TRUNK FLOOR
SPARE TIRE
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Locate the jacking point nearest
thetireyouneedtochange.Itis
pointed to by an arrow molded into
the underside of the body. Place
the jack under the jacking point.
Turn the end bracket clockwise
until the top of the jack contacts
the jacking point. Make sure the
jacking point tab is resting in the
jack notch.Use the extension and the wheel
nut wrench as shown to raise the
vehicle until the f lat tire is of f the
ground.
Loosen each wheel nut 1/2 turn
with the wheel nut wrench.
6.
7.8.
Changing a Flat Tire
246
EXTENSION
WHEEL NUT WRENCH
WHEEL NUT WRENCH