key Acura TL 2007 User Guide

The master key fits all the locks on
your vehicle.
The valet key works only in the
ignition and the driver’s door lock.
You can keep the trunk pass-through
cover and the glove box locked when
you leave your vehicle and the valet
key at a parking f acility.Youshouldhavereceivedakey
number tag with your key. You will
need this key number if you ever
have to get a lost key replaced. Use
only an Acura-approved key blank.
Donotdropthekeysorsetheavy
objects on them. Protect the key f rom direct
sunlight, high temperature, and
high humidity.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
These keys contain electronic
circuits that are activated by the
immobilizer system. They will not
work to start the engine if the
circuits are damaged.
The valet key does not contain a
battery. Do not try to take it apart.
Keys
92
KEY NUMBER
TAG
VALET
KEY
(GRAY)
MASTER
KEY
——
y


y
(%yy

Always make sure the key is f ully
extended when you insert it to the
ignition switch. If the key is not f ully
extended the immobilizer system
may not operate properly and
prevent the engine f rom starting.Thekeymaycomeincontactwith
your f inger while being retracted or
extended. Make sure your f ingers do
not touch the pivot of the key when
retracting or extending it.
The master key can be retracted into
theremotetransmitter.Tousethe
key, push the release button. The
key should be f ully extended. To
retract the key, push the release
buttonandatthesametimepushthe
key into the remote transmitter until
it is securely latched.Retractable Master Key
Keys and Locks
Inst rument s and Cont rols
93
Push
RELEASE BUTTON
——
y


y
(%yy

Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undrivable.
If you have lost your key and you
cannot start the engine, contact your
dealer. If the system repeatedly does not
recognize the coding of your key,
contact your dealer.
The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on
brief ly, then go of f . If the indicator
starts to blink, it means the system
does not recognize the coding of the
key. Turn the ignition switch to the
LOCK (0) position, remove the key,
reinsert it, and turn the ignition
switch to the ON (II) position again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.
As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Immobilizer System
94
——
y

y
(%yy

µµ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shif t
lever must also be in Park. If the f ront wheels are turned, the
anti-theft lock may make it difficult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position. You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
the driver’s door. Remove the key to
turn of f the beeper.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
LOCK (0) A CCESSORY (I)
ON (II)
ST A RT (III)
Ignition Switch
Inst rument s and Cont rols
95
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.
——
y

y
(%y
y

Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. Push the bottom of
the switch to lock the doors and the
toptounlockthem.
Each door has a lock tab on the top.
Push the tab down to lock the door
and pull it up to unlock. When you
push down the lock tab on the driver’s
door, all the doors lock.All doors can be locked f rom the
outsidebyusingthekeyinthe
driver’s door. To unlock only the
driver’s door, insert the key, turn it,
and then release it. The remaining
doors unlock when you turn the key
a second time within a f ew seconds.
With the driver’s door open and the
key in the ignition, both master door
lock switches are disabled. If you try
to lock an open driver’s door by
pushing in the lock tab, all doors will
unlock when you close the driver’s
door.
To lock any door when getting out of
the vehicle, push the lock tab down,
and close the door.
L ockout Prevent ion
Door L ocks
96
——
y


y
(%y

y

To open the trunk, press the trunk
releasebuttonontheleftcornerof
the dashboard. To open the trunk
from the outside, press the trunk
release button on the remote
transmitter.
To close the trunk, press down on
the trunk lid. If
your vehicle’s battery goes dead or
is disconnected, you can open the
trunk from the rear seat by pulling
the trunk release handle. Reach the
handle through the trunk pass-
th rough.
Keep the trunk lid closed at all times
while driving to avoid damaging it,
and to prevent exhaust gas from
getting into the interior. See ,page . To protect items in the trunk, you
can disable the trunk-release button
on the dashboard by turning off the
trunk main switch in the glove box,
locking the glove box, and locking
the trunk pass-through cover with
the master key.
If you need to give the key to
someone else, give them the valet
key.
52 Carbon
Monoxide Hazard
Trunk
Inst rument s and Cont rols
97
ON
OFF
——
y


y
(%y
y

µ
µ µ
µ
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, refer to Keyless Memory
Settings on page . Press this button once
to unlock the driver’s door or all the
doors (depending on the keyless
memory setting). Press it twice to
unlock the other doors. Some
exterior lights will f lash twice each
time you press the button.
The ceiling light (if the ceiling light
switch is in the center position) will
come on when you press the
UNLOCK button. If you do not open
anydoorswithin30seconds(or
whatever setting the relock timer is
set to), the light f ades out. If you
relock the doors with the remote
transmitter before 30 seconds have
elapsed, the light will go of f
immediately.
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds (depending
on the keyless memory setting), you
will hear a beep to verify that the
doors are locked and the security
system has set. You cannot lock the
doors if any door is not f ully closed
or if the key is in the ignition switch. Pressthisbuttonfor
about 1 second to open the trunk.
Pressthisbuttonfor
about 2 seconds to attract attention:
the horn will sound, and the exterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
81
UNL OCK
LOCK TRUNK
PA NIC
Remote Transmitter
Inst rument s and Cont rols
99
LOCK
BUTTON
UNLOCK
BUTTON
PANIC
BUTTON
TRUNK
BUTTON
——
y

y
(%y
y

Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.If it takes several pushes on the
button to lock or unlock the doors
and the tailgate, replace the battery
as soon as possible.
To replace the battery:Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
Separate the keypad from the
transmitter by pushing any button
f rom outside.
Battery type: CR1616
1.
2.
Remote Transmitter CareReplacing the Transmitter
Battery
Remote Transmitter
100
KEYPAD
SCREW
——
y
y
(%y
y

µ
Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing up), then
insert it in the keypad.
An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations
for battery disposal.
Snap the two halves of the keypad,
then install the parts in reverse
order.
Place a cloth on the edge of the
keypad, and remove the upper half
by caref ully prying on the edge
with a small f lat-tip screwdriver or
coin. 4.
5.
3.
As required by the FCC: This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
Inst rument s and Cont rols
101
BATTERY
——
y

y
(%y
y

Customized settings
(see page ).
Driving position memory
(see page ).
When you unlock the driver’s door
with a remote, that remote’s keyless
memory settings are activated.
Depending on which remote was
used, a WELCOME DRIVER 1 or
WELCOME DRIVER 2 message
appears on the multi-inf ormation
display. The driver’s ID (MEMORY
1 or MEMORY 2) is printed on the
back of each remote. Here are the settings activated by
the remote;
When you unlock and open the
driver’s door with the remote, the
driver’s seat (except power lumbar)
and outside mirrors move to the
positions stored in memory. An
indicator on one of the driving
position memory buttons also comes
on.
To turn of f this f eature, press and
hold the LOCK and UNLOCK
buttonsatthesametime.TheLED
in the remote will blink twice. Then
release the buttons. Doing this
cancels the keyless memory settings
f or that remote and restores the
def ault settings.
To turn the keyless memory settings
back on, repeat this procedure. The
LED will blink once to indicate the
f eature has been turned on.
77
108
K eyless Memory Settings
Remote Transmitter
102
TM
——
y
y
(%y
y