navigation Acura TL 2007 Owner's Guide

Depending on where you drive, you
may experience reception problems.
Interf erence can be caused by any of
these conditions:Driving on the north side of a
large commercial truck on an
east/west road.
Driving in tunnels.
Driving on a road beside a vertical
wall, steep clif f , or hill to the south
of you.
Driving on the lower level of a
multi-tiered road.
Driving on a single lane road
alongside dense trees taller than
50 ft. (15 m) to the south of you. If you decide to purchase XM
satellite radio service, contact XM
Radio at, or at
1-800-852-9696. You will need to give
them your radio I.D. number and
your credit card number. To get your
radio I.D. number, turn the TUNE knob until ‘‘0’’ appears in the display.
Your I.D. will appear in the display.
There may be other geographic
situations that could af f ect XM radio
reception. Driving on the north side of an
east/west mountain road.
If your XM Radio service has expired
or you purchased your vehicle f rom
a previous owner, you can listen to a
sampling of the broadcasts available
on XM Satellite Radio. With the
ignition switch in the ACCESSORY
(I) or ON (II) position, push the
power/volume knob to turn on the
audio system and press the XM
RADIO button. A variety of music
types and styles will play. While waiting f or activation, make
sure your vehicle remains in an open
area with good reception. Once your
audio system is activated, you should
be able to listen to XM radio
broadcasts. XM Radio will continue
to send an activation signal to your
vehicle for at least 12 hours from the
activation request. If the service has
not been activated after 36 hours,
contact XM Radio. After you’ve registered with XM
Radio, keep your audio system in the
Satellite Radio mode while you wait
f or activation. This should take about
30 minutes.As required by the FCC:
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
www.xmradio.com
Receiving Satellite Radio Service
Audio System (Models without Navigation System)
144
——
y
y
(%y
y

µ´
CONT INUED
Audio System (Models without Navigation System)
Operating the Disc Changer
Features
145
DISC SLOT
SEEK BUTTONS
SCAN BUTTON RANDOM BUTTONDISC BUTTONDISC BUTTON
PWR/VOL KNOB
EJECT BUTTON
AM/FM BUTTON
DISC/TAPE BUTTON
LOAD BUTTON
REPEAT BUTTON
——
y

y
(%y
y

µ
µµ
µ
µ
µ
µ
µ
Your vehicle’s audio system has an
in-dash disc changer that holds up to
six discs. You operate this disc
changer with the same controls used
f or the radio. To operate the disc
changer, the ignition switch must be
in the ACCESSORY (I) or ON (II)
position.
The disc changer can play these disc
formats:
CD
CD-R
DVD-A
DTS This audio system can also play
CD-Rs and CD-RWs compressed in
MP3 or WMA f ormats. When
playing a disc in MP3, you will see
‘‘MP3’’ in the display. In WMA
f ormat, ‘‘WMA’’ will appear in the
display. You can select up to 255
folders or tracks.
NOTE:
If a f ile on an MP3 or WMA disc is
protected by digital rights
management (DRM), the audio unit
displays FORMAT, and then skips to
the next f ile.
The specif ications of the compatible
MP3 f ile are:
The specif ications of the compatible
WMA f ile are:
‘‘DTS’’ and ‘‘DTS Digital Surround’’
are registered trademarks of Digital
Theater Systems, Inc. Sampling f requency: 32/44.1/48
kHz
Bit rate: 48/64/80/96/128/160/
192 kbps
Compatible with variable bit rate
and multi-session.
Maximum layers (including
ROOT): 8 layers
Sampling f requency: 32/44.1/48
kHz (MPEG1)
16/22.05/24 kHz (MPEG2)
Bit rate: 32/40/48/56/64/80/96/
112/128/160/192/224/256/320
kbps (MPEG1), 8/16/24/32/40/
48/56/64/80/96/112/128/144/
160 kbps (MPEG2) Compatible with variable bit rate
and multi-session.
Maximum layers
(including ROOT): 8 layers
Audio System (Models without Navigation System)
146
TM
Do not use discs with adhesive labels.
The label can curl up and cause the
disc to jam in the unit.
——
y
y
(%y

y

To load multiple discs in one
operation:With the ignition switch in the
ACCESSORY (I) or ON (II)
position, press and hold the LOAD
button until you hear a beep and
see ‘‘LOAD’’ in the display, then
release the button.
Insert a disc into the slot. Insert it
only about half way; the drive will
pull it in the rest of the way.
When the ‘‘DISC LOAD’’ appears
in the display, insert the next disc
into the slot. To load a single disc:
Press and release the LOAD
button.
The disc number f or an empty
position is highlighted and the
green load indicator comes on.
When you see ‘‘LOAD’’ in the
display, insert the disc into the slot.
Insert it only about halfway; the
drive will pull it in the rest of the
way.
If you press the LOAD button while
a disc is playing, the system will stop
playing that disc and start the
loading sequence. It will then play
the disc just loaded. Select the disc changer by pressing
the DISC/TAPE button. The system
will begin playing the last selected
disc in the disc changer. You will see
the disc and track numbers
displayed.
Repeat this until all six positions
are loaded. The system will then
begin playing the last disc loaded. If you stop loading discs bef ore all
six positions are f illed, the system
will wait f or 15 seconds, stop the load
operation, and begin playing the last
disc loaded.
To select a dif f erent disc when all six
positions are loaded, press the
corresponding number on the preset
buttons.
1.
2.
3.
4. 1.
2.
CONT INUED
L oading Discs in the Changer
Playing a Disc
Audio System (Models without Navigation System)
Features
147
——
y

y
(%y
y

´µ
µ ´
µ
¼
Each time you press the DISP button,
the display shows you the text data
on a disc, if the disc was recorded
with text data.
You can see the album, artist, and
track name in the display. If a disc is
recorded in MP3 or WMA, you can
see the f older and f ile name, and the
album, artist, and track tag.
The display shows up to about 16
characters of selected text data (the
foldername,filename,etc.).If the
text data has more than 16
characters, you will see the first 15
characters and the indicator in
the display. Press and hold the DISP
button until the next 16 characters
are shown. You will also see some text data
under these conditions:
When a new f older, f ile, or track is
selected.
When you change the audio mode
to play a disc with text data or in
MP3 or WMA.
When you insert a disc, and the
system begins to play. Use the SEEK or SEEK button
while a disc is playing to select
passages and change tracks (f iles in
MP3/WMA mode).
Each time you press and
release the SEEK button, the
player skips f orward to the
beginning of the next track (f ile in
MP3 or WMA). Press and release
the SEEK button to skip
backward to the beginning of the
current track. Press it again to skip
to the beginning of the previous
track.
With the f older name, you will see
the FOLDER indicator in the display.
The TRACK indicator is shown with
the file or track name.
When loading a CD-DA with text
data, the album and track name are
showninthedisplay.Withadiscin
MP3 or WMA, the display shows the
f older and f ile name.
T ext Dat a Display Funct ion
T o Change or Select T racks/Files
SEEK
Audio System (Models without Navigation System)
148
——
y

y
(%y
y

µ
µ µ
µ
µ
In MP3 or WMA mode In MP3 or WMA mode
To
select a different folder, turn the
TUNE knob to move to the
beginning of the next f older. Turn
theknobtotherighttoskiptothe
next f older, and to the lef t to move to
the beginning of the current f older.
Turn it again to skip to the beginning
of the previous f older. Turning the
TUNE knob more than one click
skips several f olders at a time.
To continuously replay
a track (f iles in MP3 or WMA mode),
press and release the RPT button.
You will see RPT in the display.
Press and hold the RPT button for 2
seconds to turn it off. This feature,
when activated, replays all f iles on
the selected f older in the order they
are compressed. To activate folder
repeat, press the RPT button twice.
You will see F-RPT in the display.
The system continuously replays the
current f older. To turn of f f older
repeat, press the RPT button for 2
seconds, or push it twice.
Each time you press and release the
RPT button, the mode changes f rom
f ile repeat to f older repeat, then to
normal playing. When you press
the RPT button three times, D-RPT
appears in the display, and the
system continuously replays the
current disc. To turn this f eature of f ,
press the RPT button or touch DISC
RPT again.
This f eature plays
the tracks within a disc (the f iles
within a f older in MP3 or WMA
mode) in random order. To activate
random play in CD-DA f ormat, press
and release the RDM button. In MP3
or WMA mode, press the RDM
button to activate random play within
a f older. You will see F-RDM in the
display. To return to normal play,
press the RPT button f or 2 seconds,
or push it twice.
CONT INUED
FOLDER SELECTION
REPEAT (TRACK/FILE
REPEAT) FOL DER-REPEA T
DISC REPEAT
RANDOM (Random within a
disc/f older)
Audio System (Models without Navigation System)
Features
149
——
y

y
(%y
y

µµ
µ
In MP3 or WMA mode In MP3 or WMA mode
To take the system out of disc mode,
press the AM/FM button, or insert a
tape in the tape player. To return to
disc mode, press the DISC/TAPE
button.
If you turn the system of f while a
disc is playing, either with the
power/volume knob or by turning
of f the ignition switch, the disc will
stay in the drive. When you turn the
system back on, the disc will begin
playing where it lef t of f .
The scan f unction samples all tracks
(f iles in MP3 or WMA) on the disc in
the order they are recorded on the
disc. To activate scan, press the
SCAN button. In MP3 or WMA
mode, press the SCAN button to
select SCAN. You will see SCAN in
the display. You will get a 10 second
sampling of each track/f ile on the
disc. Press the SCAN button again to
get out of scan mode and play the
last track/f ile sampled. This
feature, when activated, samples the
f irst f ile of each f older on the disc.
To activate folder scan, press the
SCAN button twice. You will see
F-SCAN in the display.
The system plays the f irst f ile in the
f irst f older f or about 10 seconds. If
you do nothing, the system will then
play the f irst f iles in the remaining
f olders f or 10 seconds each. Af ter
playing the f irst f ile of the last f older,
the system plays normally.
To turn folder scan off, press either
SEEK button, select a dif f erent
f older with the TUNE knob, or press
the SCAN button.
This
feature, when activated, plays all
f iles in each f older in random order.
To activate folder random, press the
RDM button twice. You will see
RDM in the display. The system will
then select and play f iles randomly.
This continues until you deactivate
f older random by pressing the RDM
button again, or by selecting a
dif f erent f older with the TUNE knob. To Stop Playing a Disc
SCA N (T RA CK /FIL E SCA N) F-SCAN (FOLDER SCAN)
FOLDER-RANDOM
Audio System (Models without Navigation System)
150
——
y
y
(%y
y

To remove a different disc from the
changer,firstselectitbypressing
the corresponding number on the
preset button. When that disc begins
playing, press the eject button.
When you press the eject button
while listening to the radio, or with
the audio system turned of f , the disc
that was last selected is ejected.
Af ter that disc is ejected, pressing
the eject button again will eject the
next disc in numerical order. By
doing this six times, you can remove
all the discs f rom the changer.
You can also eject discs when the
ignition switch is of f :
To eject one disc, press and release
the eject button.
To eject all discs, press and hold the
eject button until the system beeps.
To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJECT’’ in the display.
When you remove the disc f rom the
slot, the system automatically begins
the load sequence so you can load
another disc in that position. If you
do not load another disc within 10
seconds, the system selects the
previous mode (AM, FM1, FM2,
tape, or XM Radio).
If you do not remove the disc f rom
the slot, the system reloads it after
10 seconds and puts the changer in
pause mode. To begin playing the
disc, press the DISC/TAPE button. Removing Discs f rom the
Changer
Audio System (Models without Navigation System)
Features
151
——
y
y
(%y
y

Û
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Make sure the open side of
thetapeisfacingright,theninsert
thetapemostof thewayintotheslot.
Thesystemwillpullthetapeinthe
rest of the way and begin to play it.
Thetapedirectionindicatorinthe
display comes on to show you which
side of the tape is playing. The
indicates the side you inserted
upward is now playing. If you want to
play the other side, press the PLAY/
PROG (preset 2) button. When the
player reaches the end of the tape, it
will automatically reverse direction
and play the other side.
Audio System (Models without Navigation System)
Playing a T ape
152
EJECT BUTTON
SEEK BUTTONS
REWIND BUTTON DOLBY BUTTON
PLAY/PROGRAM BUTTON
DISC/TAPE
BUTTON
AM/FM
BUTTON
PWR/VOL KNOB
REPEAT BUTTON
FAST FORWARD BUTTON
——
y

y
(%y
y

Î
Î
µ
µµ ´
µ
Dolby noise reduction turns on
when you insert a tape. The
indicator will come on in the
display. If the tape was not recorded
in Dolby, turn it of f by pressing the (preset 4) button. Dolby
remains of f until you press the
button again. To remove the tape, press the eject
button. If you want to turn the player
of f , press the power/volume knob or
turn off the ignition. The tape will
remain in the drive. When you turn
the system back on, the tape will
begin playing where it lef t of f . To rewind the tape,
push the (preset 1) button. You
will see REW in the display. To f ast
f orward the tape, push the (preset 3) button. You will see
FF displayed. Press the , ,
or PLAY/PROG button to take the
system out of rewind or f ast f orward.
Press the SEEK button
to f ind the beginning of the current
song or passage. Press the SEEK
button to f ind the beginning of the
next song or passage. When the
system reaches the beginning of a
song or passage, it begins to play it.
Press the RPT button
to continuously play a song or
passage. You will see RPT displayed.
The track will repeat until you press
the RPT button again.
To switch to the AM/FM radio, XM
Radio, or disc changer while a tape is
playing, press the AM/FM button,
XM button, or DISC/TAPE button.
To change back to the tape player,
press the DISC/TAPE button.
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing
Corporation. ‘‘DOLBY’’ and the double-D symbol are trademarks of Dolby Laboratories
Licensing Corporation.
CONT INUED
T o Stop Playing a T ape T ape Search Functions
FF/REW
SK IP
REPEAT
Audio System (Models without Navigation System)
Features
153
——
y
y
(%y
y