ignition Acura TL 2007 Repair Manual

With the clutch pedal pressed,
move the shift lever to the first/
second gear side of the neutral
gate, then shif t to reverse.If you are still unable to shif t to
reverse, apply the parking brake,
and turn the ignition key to the
ACCESSORY (I) or LOCK (0)
position.
Press the clutch pedal, and shif t to
reverse.
With the clutch pedal still pressed,
start the engine.
If you need to use this procedure to
shif t to reverse, your vehicle may be
developing a problem. Have the
vehicle checked by your dealer.
1. 2.
3.
4.
Manual T ransmission
252
——
y

y
(%yy

To shif t f rom any position, press
f irmly on the brake pedal. You
cannot shif t out of Park when the
ignition switch is in the LOCK (0) or
ACCESSORY (I) position.
These indicators on the instrument
panel show which position the shif t
lever is in. The illuminated number
under the tachometer shows you the
gear you have selected in the
Sequential SportShif t mode.
The ‘‘D’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch to the ON (II)
position. If it f lashes while driving (in
any shif t position), it indicates a possible problem in the transmission.
If the malf unction indicator lamp
comes on along with the ‘‘D’’
indicator, there is a problem with the
automatic transmission control
system. Avoid rapid acceleration and
have the transmission checked by
your dealer as soon as possible.
CONT INUED
Shif t L ever Position Indicators
Shif ting
Automatic Transmission
Driving
253
——
y

y
(%yy

µ
µ
µµ µ
µ To
avoid transmission damage, come
to a complete stop before shifting
into Park. The shift lever must be in
Park before you can remove the key
from the ignition switch.
Use this position for
your normal driving. The transmis-
sion automatically adjusts to keep
the engine at the best speed for the
driving conditions.
ForfasteraccelerationwheninD,
you can get the transmission to
automatically downshift by pushing
the accelerator pedal to the floor.
The transmission will shift down one,
two or three gears, depending on
your speed.
Press
the brake
pedal to shift from Park to reverse.
To shift from neutral to reverse,
come to a complete stop and then
shift.
Your vehicle has a reverse lockout so
you cannot accidentally shift to
reverse from neutral or any other
driving position when the vehicle
speed exceeds 5 6 mph (8 10
km/h).
If you cannot shift to reverse when
the vehicle is stopped, press the
brake pedal, slowly shift to neutral,
andthenshifttoreverse.
If there is a problem in the reverse
lockout system, or your vehicle’s battery
is disconnected or goes dead,
you cannot shift to reverse. (Refer to
on page ).
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop briefly with
the engine idling. Shift to the Park
position if you need to leave your
vehicle and apply the parking brake.
Press on the brake pedal when you
are moving the shift lever from
neutral to another gear.
This position mechani-
cally locks the transmission. Use
Park whenever you are turning off or
starting the engine. To shift out of
Park, you must press on the brake
pedal and have your foot off the
accelerator pedal.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page . 258 258
To shift from:
PtoR
RtoN
NtoD DtoL
LtoD
DtoN NtoR RtoP Do this:
Press the brake pedal, then
move the shift lever.
Move the lever.
Drive (D)
Reverse (R)
Shif t L ock Release
Neutral (N)
Park (P)
Shif t L ock Release
Automatic Transmission
254
——
y

y
(%yy

à
à
à
àà
à
à
à
To shift from
21
32
43
54 Speed range
under 29 mph
(47 km/h)
under 56 mph
(90 km/h)
under 93 mph
(150 km/h)
under 130 mph
(209 km/h)
To release the reverse lockout, make
sure the ignition switch is in the
ACCESSORY(I) position.Make sure the ignition switch is in
the LOCK (0) position. Set the parking brake.
This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
is also used to release the reverse
lockout. If you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
rpm below the red zone.
When you are in Sequential
SportShif t mode, and the vehicle is
stopped, push f orward on the shif t
lever to shif t to second gear. You will
see ‘‘2’’ in the display. Starting out in
second gear will help to reduce
wheelspin in deep snow or on a
slippery surf ace. To shift from
21
32
43
54 Speed range
under 37 mph
(54 km/h)
under 61 mph
(98 km/h)
under 93 mph
(150 km/h)
under 130 mph
(209 km/h)
1.
2.
Type S only
Shif t L ock Release Engine Speed L imiter
Starting in Second Gear
Automatic Transmission
258
——
y
y
(%yy

The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle turns
more or less than desired. It also
assists you in maintaining traction
while accelerating on loose or
slippery road surfaces. It does this
by regulating the engine’s output,
and by selectively applying the
brakes.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. If
the indicator does not come on
when the ignition switch is turned to
the ON (II) position, there may be a
problem with the VSA system. Have
your dealer inspect your vehic le as
soon as possible.
If this indicator comes on while
driving, pull to the side of the road
when it is safe, and turn off the
engine. Reset the system by
restarting the engine. If the VSA
system indicator stays on, or comes
back on while driving, have the VSA
system inspected by your dealer. When VSA activates, you will see the
VSA activation indicator blink (see
page ). On manual transmission models, if
the VSA system is of f and you
accelerate f rom a stop, the vehicle
may pull, and it may take extra effort
to return the steering wheel to
center.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
61
VSA System Indicator VSA A ctivation Indicator
Vehicle Stability Assist (VSA) System
264
——
y

y
(%yy

The TPMS can misinterpret the tire
pressure because of differences in
the air temperatures. For example, if
youcheckandfillyourtiresina
warm area, then drive in extremely
cold weather, the tire pressure will
be lower than measured and could
be underinflated and cause the
TPMS indicators to come on. Or, if
youcheckandadjustyourtire
pressu re in cooler conditions, and
drive into extremely hot conditions,
thetiresmaybecomeoverinflated.
However, the TPMS indicators will
not come on if the tires are
overinflated.
Refer to page for tire inflation
guidelines. Toselectthetirepressuremonitor,
press
the INFO button several times
with the ignition switch in the ON
(II) position.
Although
your tire pressure is
monitored, you must manually check
thetirepressuresmonthly.
Each tire, including the spare, should
be checked monthly when the
vehicle is cold, and set to the
recommended inflation pressure as
sp ecified on the vehicle placard and
intheowner’smanual(seepage ).
You will see the above display on the
multi-inf ormation display when all
tire pressures are normal.
302 303
CONT INUED
Tire Pressure Monitor
Tire Pressure Monitoring System (TPMS)
Driving
267
——
y
y
(%yy

ÛÝ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ µ
µ
CONTINUED
Displayed
Engine Oil Life (%)
100 %
90 %
80 %
70 %
60 %
50 %
40 %
30 %
20 %
15 %
10 %
5%
0%
Calculated
Engine
Oil Life (%)
100 % 91 %
90 % 81 %
80 % 71 %
70 % 61 %
60 % 51 %
50 % 41 %
40 % 31 %
30 % 21 %
20 % 16 %
15 % 11 %
10 % 6 %
5% 1%
0%
Your vehicle displays engine oil life
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perform engine oil
replacement and indicated
maintenance service.
Based on the engine operating
conditions and accumulated engine
revolutions, the onboard computer in
your vehicle calculates the remaining
engine oil life and displays it as a
percentage. To see the current engine oil life,
turn the ignition switch to the ON
(II) position, then push and release
the INFO ( / ) button repeatedly
until the engine oil lif e appears (see
page ). The remaining engine oil lif e is
displayed on the multi-information
display according to this table:
72
Maintenance Minder
Engine Oil L if e Indicator
Maint enance
273
——
y

y
(%yy

ÛÝÛÝ
All maintenance items displayed in
the information display are in code.
For an explanation of these
maintenance codes, see page .Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100%’’ on the display the
next time you turn the ignition
switch to the ON (II) position.
If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:
Turn the ignition switch to the ON
(II) position.
Press the INFO ( / ) button
repeatedly until the engine oil lif e
is displayed. Press and hold the SEL/RESET
button f or 10 seconds. The multi-
inf ormation display will ask f or a
conf irmation.
If you are sure you want to reset
the display, press the SEL/
RESET button to select ‘‘OK.’’
If you do not want to reset the
display, press the INFO ( / )
button to select ‘‘Cancel.’’
1.
2. 3.
278
Maintenance Minder
Maintenance Main Items and Sub
Items Resetting the Engine Oil Lif e
Indicator
Maint enance
275
MAINTENANCE MAIN ITEM
MAINTENANCE SUB ITEMS
——
y
y
(%yy

Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.Open the trunk. Raise the trunk
f loor by lif ting up on the back edge.
Take the tool case out of the spare
tire.
Unscrew the wing bolt and take
the spare tire out of its well.
Park the vehicle on f irm, level, and
non-slippery ground. Put the
transmission in Park (automatic)
or reverse (manual). Apply the
parking brake.
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area that is
far away from the traffic lanes.
5. 4.
3.
2. 1.
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
313
TOOL CASE
JACK
SPARE TIRE TRUNK FLOOR
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.
——
y
y
(%y
y

Diagnosing why the engine won’t
start falls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position: You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
faster than normal, but the engine
does not start up and run. When
you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all. Turn
the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the fuses. If the fuses
are OK, there is probably
something wrong with the
electrical circuit for the ignition
switch or starter motor. You will
need a qualified technician to
determine the problem. See
on page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page ). You can
then try jump starting the vehicle
from a booster battery (see page
).
Turn
the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page .
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, the shif t
lever must be in Park or neutral.
Check these things:
320 331
308
320
If theEngineWon’tStart
Nothing Happens or the Starter
Motor Operates Very Slowly
Emergency T owing
Jump Starting
318
——
y
y
(%yy