battery Acura TL 2008 Owner's Guide

If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.Fill the f uel tank. Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and trunk seals.Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry.
Leave the parking brake off. Put
the transmission in reverse
(manual) or Park (automatic).
Vehicle Storage
Maint enance
315
\f—\f—
y
\fy
(%\fy\f\fy
2008 TL

Diagnosing why the engine won’t
start f alls into two areas, depending
on what you hear when you turn the
ignition switch to the START (III)
position:You hear nothing, or almost
nothing. The engine’s starter
motor does not operate at all, or
operates very slowly.
You can hear the starter motor
operating normally, or the starter
motor sounds like it is spinning
f aster than normal, but the engine
does not start up and run. When you turn the ignition switch to
the START (III) position, you do not
hear the normal noise of the engine
trying to start. You may hear a
clicking sound, a series of clicks, or
nothing at all.
Turn the ignition switch to the
START (III) position. If the
headlights do not dim, check the
condition of the f uses. If the f uses
are OK, there is probably
something wrong with the
electrical circuit f or the ignition
switch or starter motor. You will
need a qualif ied technician to
determine the problem. See
on page .
If the headlights dim noticeably or
go out when you try to start the
engine, either the battery is
discharged or the connections are
corroded. Check the condition of
the battery and terminal connec-
tions (see page ). You can
then try jump starting the vehicle
f rom a booster battery (see page ).
Turn the ignition switch to the ON
(II) position. Turn on the
headlights, and check their
brightness. If the headlights are
very dim or do not come on at all,
the battery is discharged. See
on page .
Check the transmission interlock.
If you have a manual transmission,
the clutch pedal must be pushed
all the way to the f loor or the
starter will not operate. With an
automatic transmission, the shif t
lever must be in Park or neutral.
Check these things:
326 337
314
326
If theEngineWon’tStart
Nothing Happens or the Starter
Motor Operates Very Slowly
Emergency T owing
Jump Starting
324
\f—\f—
y
\fy
(%\fy\fy
2008 TL

´´
Although this seems like a simple
procedure, you should take several
precautions.
You cannot start a vehicle with an
automatic transmission by pushing
or pulling it.
Open the hood, and check the
physical condition of the battery.
In very cold weather, check the
condition of the electrolyte. If it
seems slushy or like ice, do not try
jump starting until it thaws.
The numbers in the illustration
show you the order to connect the
jumper cables.
Connect one jumper cable to the
positive ( ) terminal on your
battery. Connect the other end to
the positive ( ) terminal on the
booster battery.
Turn of f all the electrical
accessories: climate control, audio
system, lights, etc. Put the
transmission in neutral (manual)
or Park (automatic), and set the
parking brake.
1.
2.
3.
Jump Starting
To Jump Start Your Vehicle:
326
A battery can explode if you do
not follow the correct procedure,
seriously injuring anyone
nearby.
Keep all sparks, open flames,
and smoking materials away
from the battery.If a battery sits in extreme cold, the
electrolyte inside can f reeze.
Attempting to jump start with a f rozen
battery can cause it to rupture.
\f—\f—
y

y
(%\fy\f
y
2008 TL

µStart the vehicle. If the starter
motor still operates slowly, check
that the jumper cables have good
metal-to-metal contact.
Connect the second jumper cable
to the negative ( ) terminal on
the booster battery. Connect the
other end to the grounding strap
as shown. Do not connect this
jumper cable to any other part of
the engine.
If the booster battery is in another
vehicle, have an assistant start
that vehicle and run it at a fast idle. Once the vehicle is running,
disconnect the negative cable f rom
your vehicle, then f rom the
booster battery. Disconnect the
positive cable f rom your vehicle,
and then from the booster battery.
Keep the ends of the jumper cables
away from each other and any metal
on the vehicle until everything is
disconnected. Otherwise, you may
cause an electrical short.
7.
6.
5.
4.
Jump Starting
T aking Care of t he Unexpect ed
327
\f—\f—
y
y
(%\fy\fy
2008 TL

Saf ely pull of f the road, and shut
of f the engine. Turn on the hazard
warning indicators.
If necessary, add oil to bring the
level back to the full mark on the
dipstick (see page ).
Start the engine, and watch the oil
pressure indicator. If it does not go
out within 10 seconds, turn of f the
engine. There is a mechanical
problem that needs to be repaired
bef ore you can continue driving
(see on page).
Let the vehicle sit f or a minute.
Open the hood, and check the oil
level (see page ). An engine
very low on oil can lose pressure
during cornering and other driving
maneuvers.
Immediately turn of f all electrical
accessories. Try not to use other
electrically operated controls such as
the power windows. Keep the engine
running; starting the engine will
discharge the battery rapidly.
Go to a service station or garage
where you can get technical
assistance.
This indicator should never
come on when the engine is
running. If it starts f lashing or stays
on, the oil pressure has dropped very
low or lost pressure. Serious engine
damage is possible, and you should
take immediate action. If the charging system
indicator comes on brightly
when the engine is running, the
battery is not being charged.
1.
2.
3.
4. 240
287
337
L ow Oil Pressure Indicator, Charging System Indicator
L ow Oil Pressure Indicator
Emergency T owingCharging System Indicator
330
Running the engine with low oil
pressure can cause serious mechanical
damage almost immediately. Turn of f
the engine as soon as you can saf ely get
the vehicle stopped.
\f—\f—
y
y
(%\fy\fy
2008 TL

If the indicator comes on repeatedly,
even though it may go of f as you
continue driving, have the vehicle
checked by your dealer as soon as
possible.
If this indicator comes on
while driving, it means one
of the engine’s emissions control
systems may have a problem. Even
though you may f eel no dif f erence in
your vehicle’s perf ormance, it can
reduce your f uel economy and cause
increased emissions. Continued
operation may cause serious damage.
Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
If you have recently ref ueled your
vehicle, the indicator coming on
could be due to a loose or missing
f uel f ill cap. You will also see a
‘‘TIGHTEN FUEL CAP’’ message on
the multi-information display.
Tighten the cap until it clicks at least
once (see page ). Tightening the
cap will not turn the indicator of f
immediately; it can take several days
of normal driving. If the battery in your vehicle has
been disconnected or gone dead,
thesecodesmaybeerased.Ittakes
several days of driving under various
conditions to set the codes again.
To check if they are set, turn the
ignition switch to the ON (II)
position, without starting the engine.
The malf unction indicator lamp will
come on f or 20 seconds. If it then
goes of f , the readiness codes are set.
If it blinks f ive times, the readiness
codes are not set. If possible, do not
take your vehicle f or an emissions
test until the readiness codes are set.
Refer to for
more information (see page ).
238 355
Malf unction Indicator L amp
Readiness Code
Emissions T estingT aking Care of t he Unexpect ed
331
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and engine. Those repairs may
not be covered by your vehicle’s
warranties.
\f—\f—
y


y
(%\fy\fy
2008 TL

No. Circuits ProtectedCircuits Protected
No.
Amps. Amps.
1
2
3
4
5
Left Headlight Low Beam
Rear Defroster Coil
Left Headlight High Beam
Small Light
Right Headlight High Beam Right Headlight Low Beam
Back Up
FI ECU
Condenser Fan
Fog Light
Radiator Fan Motor
MG Clutch Relay
Horn, Stop
Rear Defroster
Back UP, ACC
Hazard Warning
VSA Pump Motor Relay
VSA Fail Safe Relay
FI ECU (ECM/PCM)
Power Seat
Heater Motor
Battery
IGI Main
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
15 A
30 A
7.5 A 10 A
7.5 A 15 A
7.5 A 15 A
30 A
10 A
30 A
7.5 A 20 A
40 A
40 A
15 A
30 A
40 A
40 A
40 A
40 A
120 A 50 A
Fuse Locations
T aking Care of t he Unexpect ed
335
UNDER-HOOD FUSE BOX
\f—\f—
y
y
(%\fy\f\fy
2008 TL

For very short distances, such as
f reeing the vehicle, you can use the
detachable towing hook that mounts
on the anchor in the f ront bumper.
If your vehicle gets stuck in sand,
mud, or snow, call a towing service
to pull it out (see page ).
To use the towing hook:Remove the cover f rom the bumper by pushing the lower part
of the cover with your f inger.
Remove the towing hook, hook
extension, and wheel nut wrench
f rom the tool case in the spare tire.
Using the wheel nut wrench,
fasten the extension into the bolt
hole.
If you decide to tow your vehicle
with all f our wheels on the ground,
make sure you use a properly-
designed and attached tow bar.
Prepare the vehicle for towing as
described above, and leave the
ignition switched in the
ACCESSORY (I) position so the
steering wheel does not lock. Make
sure the radio and any items plugged
into the accessory power socket are
turned of f so they do not run down
the battery.
3.
1. 2.
337
Emergency Towing, If Your Vehicle Gets Stuck
If Your Vehicle Gets Stuck
338
The steering system can be damaged if
the steering wheel is locked. Leave the
ignition switch in the ACCESSORY (I)
position, and make sure the steering
wheel turns f reely bef ore you begin
towing.
\f—\f—
y

y
(%\fy\fy
2008 TL

µ
µ
Î
Î Î
Î
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
ÎÎ
Î
Î
Î
Specif ications
Technical Inf ormation
345
Tires
Alignment
Engine
Battery
Fuses
Lights 3.50 x 3.39 in (89.0 x 86.0 mm)Water cooled 4-stroke
SOHC VTEC 6-cylinder (V6), gasoline engine
12 V 21 W/2.2 CP
12 V 60 W (HB3)
12 V 35 W (HID)
Size
Pressure
Toe-in
Camber
Caster60 psi (420 kPa , 4.2 kgf/cm
)
235/45R17 93W
P235/45R17 93W 3°17’
1°00’
0°30’
0.00 in (0.0 mm)
0.00 in (0.0 mm) 11.0 : 1
195.9 cu-in (3,210 cm
)
IZFR6K-11
SKJ20DR-M11
Type
BorexStroke
Displacement
Compression ratio
Spark plugs
12 V
4CP
5W
2CP
5W
5W
3CP
21 CP
51 W (HB4)
21 W
32 psi (220 kPa , 2.2 kgf/cm
)
35 psi (240 kPa , 2.4 kgf/cm)
33 psi (230 kPa , 2.3 kgf/cm)
Capacity 12 V 72 AH/20 HR
Interior
Under-hood 12 V
3.50 x 3.66 in (89.0 x 93.0 mm)
211.8 cu-in (3,471 cm
)
12 V
12 V
12 V
12 V
12 V
12 V
12 V
Headlight
(High beam/Low beam)
DRL
Front turn signal/parking
lights
Front Fog lights
Rear turn signal
Back-up lights
License plate light
Ceiling light
Trunk light
Door courtesy lights
Vanity mirror lights
Map lights
T145/70R17 106M
T135/80R16 101M
See page336or the fuse label
attached to the inside of the fuse
box door on each side of the
dashboard.
See page335or the fuse box
cover. Front
Rear
Front
Rear
Front
NGK:
DENSO:
Front/Rear
Spare
Front
Rear
Spare
Summer tire
1:
2:
3:
All season tire Type S
Type S
:
1
3
3
2
\f—\f—
y

y
(%\fy\f\fy
2008 TL

Make sure the gas tank is nearly,
but not completely, f ull (around
3/4).Without touching the accelerator
pedal, start the engine, and let it
idle f or 20 seconds.
If you take your vehicle f or an
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions. If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle retested within the
next two or three days, you can
condition the vehicle f or retesting by
doing the f ollowing.
Make sure the ambient
temperature is between 40° and
95°F.
Make sure the vehicle has been
parked with the engine of f f or 6
hours or more. Keep the vehicle in Park
(automatic) or neutral (manual).
Increase the engine speed to 2,000
rpm,andholditthereuntilthe
temperature gauge rises to at least
1/4of thescale(about3minutes).
Without touching the accelerator
pedal, let the engine idle f or 20
seconds.
1.
2.
3. 4.
5.
6.
T esting of Readiness Codes
Emissions T esting
Technical Inf ormation
355
\f—\f—
y
\fy
(%\fy\f\fy
2008 TL