battery Acura TL 2010 User Guide

When you lock the doors, some
exterior lights blink and the system
beeps once. If no exterior lights blink
and/or no beeper sounds, check to
see if the trunk or hood is open.
To change the ‘‘KEYLESS ACCESS
LIGHT FLASH’’ setting, see page.
To change the ‘‘KEYLESS ACCESS
BEEP’’ setting, see page .
Within 2 seconds of pressing the
door lock button to lock the doors or
locking the doors with remote, pull
thehandletomakesurethedoors
are actually locked. The door unlock
sensors will not operate f or about 2
seconds af ter the doors are locked. The door lock button does not work
if :
Theremoteisnotwithinthe
operating range. If you open the driver’s door, pull its
locktabrearwardonthedoor,and
shutitwhentheremoteisinsidethe
vehicle, the driver’s door will unlock.
Make sure you carry the remote
with you when you lock the doors.
Any door is open.
The power mode is not set to
VEHICLE OFF (LOCK).
The remote is in the keyless
access slot.
The remote is too close to the
vehicle.
Theremotebatteryisdead.
The vehicle battery is dead. This function is also activated on the
f ront passenger’s door. If you open
the f ront passenger’s door, and shut
it af ter pulling its lock tab rearward
whentheremoteisinsidethevehicle,
all doors will unlock.
The door lock prevention will also
activate if you try to lock the doors
with the master door lock switch
whentheremoteisinsidethevehicle.
113
114
K eyless A ccess System
Door L ock Prevent ion
Inst rument s and Cont rols
171
09/07/29 17:11:31 31TK4610_176
2010 TL

´
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations f or
battery disposal.
Battery type: CR2032 Replace the battery if necessary.
To replace the battery:
Replace the old battery with a new
battery. Place the battery so the
side is f acing up. Snap the two
halvesof theremotecaseback
together.
Remove the built-in key (see page
).
Place a cloth on the edge to
prevent scratches, then remove
the upper half by caref ully prying
on the edge with a coin.
1.
2. 3.
195
Replacing the Remote Battery
K eyless A ccess System
Inst rument s and Cont rols
175
09/07/29 17:12:17 31TK4610_180
2010 TL

Af ter entering the vehicle, insert the
keyless access remote into the slot
to start the engine (see page ). If the keyless access remote battery
dies, you may have to use the built-in
key to unlock/lock the vehicle. The
built-in key is stored inside the
keyless access remote (see page).
If the steering wheel is locked, the
engine cannot start. The multi-
inf ormation display shows you the
above message and the indicator in
the engine start/stop button blinks.
To unlock the steering wheel, apply
f orce by turning it lef t and right
while pressing the engine start/stop
button at the same time.
the multi-
inf ormation display shows the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message, then the ‘‘TO
START ENGINE:’’ message will be
shown af ter you insert the remote
into the slot. Each time you press the
engine start/stop button, the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message is shown on
the multi-information display if the
remote is not in the slot. 195
191
When the keyless access system mainswitch in the glove box is of f , T o unlock t he st eering wheel
K eyless A ccess System
Inst rument s and Cont rols
183
NOTE:
TO UNLOCK WHEEL
09/07/29 17:13:42 31TK4610_188
2010 TL

Thebatteryintheremotenormally
lasts about 2 years. To ensure
maximum battery life, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-inf ormation display shows
‘‘CHANGE KEYLESS REMOTE
BATTERY,’’ replace the battery as
soon as possible (see page ).If the remote battery becomes weak
and the power door lock/unlock
operation is disabled, you should
insert the remote into the keyless
access remote slot to set the power
mode and start the engine. Af ter
inserting the remote to the slot,
operate the engine start/stop button
as previously described (see pages
and ). For more information
on the keyless access slot, see page .
Inserting the remote does not charge
the remote battery. You should
replace the battery as soon as
possible.
The outside beeper sounds when the
power mode is in ACCESSORY, and
a door is opened, then closed.
175178 182
191
K eyless A ccess System
K eyless Remot e L ow Bat t ery
188
09/07/29 17:14:30 31TK4610_193
2010 TL

In this case, you should not shut of f
your engine until you are in a saf e
location or at your dealer, as your
vehicle may not restart.The multi-inf ormation display
shows ‘‘CHECK KEYLESS
STARTING SYSTEM.’’
If the remote battery becomes
weak and the power door lock/
unlock operation is disabled.
When the keyless access remote
system main switch in the glove
box is set to of f .
In the following two cases, you have
to insert the keyless access remote
into the keyless access remote slot
to set the power mode and start the
engine: To remove the keyless access
remote, place the vehicle in the
VEHICLE OFF (LOCK) mode, then
pull out the keyless access remote.
If the keyless access remote has
been inserted into the slot with the
keyless access remote system main
switch in the glove box turned of f , it
will lock into place when the power is
on. The slot will unlock when the
power is turned of f .
If the keyless access remote
does not come out of the slot easily,
try to push it in bef ore pulling it out.
Make sure the vehicle is in
VEHICLE OFF (LOCK) mode.
CONT INUED
K eyless A ccess System
K eyless A ccess Remote Slot
Inst rument s and Cont rols
191
NOTE:
SLOT
KEYLESS ACCESS REMOTE
09/07/29 17:15:03 31TK4610_196
2010 TL

To insert the keyless access remote:
On all models
On automatic transmission models
On manual transmission models
When you open the driver’s door,
and each time you press the engine
start/stop button, you will see the
‘‘INSERT KEYLESS REMOTE
INTO SLOT’’ message on the multi-
inf ormation display in the f ollowing
situations:When the keyless access system
main switch (see page ) is of f .
The multi-inf ormation display shows
the ‘‘ACCESSORY MODE’’ or ‘‘TO
UNLOCK KEYLESS REMOTE
TURN OFF POWER’’ message to
remind you to change the power
mode to VEHICLE OFF (LOCK).
The multi-inf ormation display shows
the ‘‘ACCESSORY MODE’’ message
to remind you that the power mode
is in ACCESSORY.
To avoid damaging the slot, do not
insert any other objects into the slot
or put a sticker on the keyless access
remote.
Inserting the remote does not charge
the remote battery. If necessary, you
should replace the battery as soon as
possible.
When the keyless access remote
system main switch in the glove box
issettoON,theremoteremains
unlocked when you insert it into the
keyless access remote slot and the
power mode is turned on.
189
K eyless A ccess System
Operat ion Guidance
Unlocked K eyless A ccess Remot e
192
09/07/29 17:15:15 31TK4610_197
2010 TL

The trunk and glove box cannot be
opened when you turn the trunk
main switch of f and lock the glove
box and trunk pass-through cover
with the built-in key. Then, the trunk
cannot be opened by using the
remote or the exterior trunk release
switch.
Remove the built-in key from the
remote by pressing the button, then
give that remote to someone else as
a valet key.
To avoid damaging the remote and
the built-in key, never pull on the
built-in key unless you are pressing
the release button.
The keyless access system uses an
electric f ield to identif y the remote.
If you use medical equipment such
as a cardiac pacemaker, ask your
doctor if the electric f ield used by
the remote will af f ect it.
Thebuilt-inkeycanbeusedtolock/
unlock the doors and the trunk when
the remote battery becomes weak
and the power door lock/unlock
operation is disabled.
To remove the built-in key, pull it out
while pressing the release button. To
reinstall the built-in key, push the
key into the remote until it clicks. Valet Function
Built-in key and Remote
K eyless A ccess System
Inst rument s and Cont rols
195
RELEASE BUTTON BUILT-IN KEY
09/07/29 17:15:40 31TK4610_200
2010 TL

Follow these precautions whenever
you use the seat heaters:Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting.
In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
Seat Heaters
Inst rument s and Cont rols
197
09/07/29 17:15:56 31TK4610_202
2010 TL

Your vehicle’s audio system may
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic f ive-digit code with
the preset buttons. Because there
are hundreds of number
combinations possible f rom the f ive
digits, making the system work
without knowing the exact code is
nearly impossible.
You should have received a radio
code card that lists your audio
system’s code and serial numbers. It
is best to store this card in a saf e
place at home. In addition, you
should write the audio system’s
serial number in this owner’s manual.
If you lose the card, you must obtain
the code number f rom your dealer.
To do this, you will need the audio
system’s serial number.If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have ten tries to
enter the correct code. If you are
unsuccessful in ten attempts, you
must then leave the system on for 1
hour bef ore trying again.
The system will retain your AM and
FM presets even if power is
disconnected.
If you have a My Acura account, you
can retrieve the anti-thef t code
online.
If your vehicle’s battery is discon-
nected or goes dead, the audio
system will disable itself . If this
happens, you will see
‘‘ENTER CODE’’ in the f requency
display (on the center display on
models with navigation system) the
nexttimeyouturnonthesystem.
Use the preset buttons to enter the
f ive-digit code. The code is on the
radio code card included in your
owner’s manual kit. When it is
entered correctly, the radio will start
playing.
Radio T hef t Protection
372
NOTE:
09/07/29 17:55:47 31TK4610_377
2010 TL

ÌÌÌÌ
CONT INUED
Press and release the HFL Talk
button each time you want to
make a command. Af ter the beep,
speak in a clear, natural tone.
Try to reduce all background
noise. If the microphone picks up
voices other than yours,
commands may be misinterpreted.
Many commands can be spoken
together. For example, you can
say ‘‘Call 123-456- ’’ or
‘‘Dial Peter.’’
To change the volume level of
HFL, use the audio system volume
knob or the steering wheel volume
controls.To hear general HFL inf ormation,
including help on pairing a phone
or setting up the system, say
‘‘Tutorial.’’
For help at any time, including a
list of available commands, say
‘‘Hands f ree help.’’
As an incoming call notif ication, you
will see the f ollowing display:
Some phones may send battery,
signal strength, and roaming status
inf ormation to HFL.Help Features
Inf ormation Display
BluetoothHandsFreeL ink(Models without navigation system)
Features
389
SIGNAL
STRENGTHHFL
MODEBATTERY
LEVEL STATUS
ROAM STATUS PHONE NUMBER
09/07/29 17:58:52 31TK4610_394
2010 TL