display Acura TL 2010 Workshop Manual

ÛÝIf the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘TRIP
COMPUTER TRIP A INFO RESET’’
and repeat the procedure again.
Press the SEL/RESET button to see
the selections.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
103
09/07/29 17:00:00 31TK4610_108
2010 TL

ÛÝÛÝ
Adjust Alarm Volume
Select the warning alarm volume
f rom three levels.
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET button to see
the selections.
Select the desired level by pressing
the INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST ALARM VOLUME’’ and
repeat the procedure again.
Multi-Inf ormation Display
104
09/07/29 17:00:10 31TK4610_109
2010 TL

ÛÝÛÝ
Auto Interior Illumination
While the headlight switch is turned
on, the interior lights gradually dim,
as the outside light level gets low.
You can customize at which outside
light level the lights start to dim.
ThereareMAX,HIGH,MID,LOW
and MIN levels and OFF for the auto
interior illumination settings.
If you want the illuminations to start
dimming as early as possible, select
MAX. For illuminations to start
dimming as late as possible, select
MIN. Choose HIGH, MID, or LOW
f or levels in between.
To disable the auto interior
illumination f unction, select OFF. You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to see
the selections.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
105
09/07/29 17:00:20 31TK4610_110
2010 TL

ÛÝ
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
INTERIOR ILLUMINATION’’ and
repeat the procedure again. When this item is set to ON, you will
see some guidance messages on the
multi-inf ormation display. You can
change this setting between on and
of f . For more inf ormation on start
guidance messages, see page .
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
182
Keyless Start Guidance Screens
On models with keyless access system
Multi-Inf ormation Display
106
09/07/29 17:00:27 31TK4610_111
2010 TL

ÛÝ
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button. Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS START GUIDANCE
SCREENS’’ and repeat the
procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
107
09/07/29 17:00:34 31TK4610_112
2010 TL

Û
Ý
ÛÝ
ÛÝ
You can customize the MEMORY
POSITION LINK setting in position
setup.
While ‘‘POSITION SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the custom setting then press the
SEL/RESET button to enter your
selection. Position Setup
Multi-Inf ormation Display
108
: Press the SEL/RESET button. : Press the INFO button ( / ). Seepage109
.
09/07/29 17:00:42 31TK4610_113
2010 TL

Û
Ý ÛÝ
Memory Position Link
On models with keyless access system
When Memory Position Link is set
to ON, the driver’s seat and the
outside mirrors move to the
positions stored in memory. To
cause the memory to activate, open
the driver’s door with the remote
transmitter. On models with keyless
access system, open the driver’s
door with the remote, or grab the
door handle while carrying the
remote.
To set the memory positions, see
page .
For inf ormation on using the remote,
see page . You can choose this item to
customize f rom ‘‘POSITION
SETUP’’ by pressing the INFO ( /
) button repeatedly. Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
164
167
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109
09/07/29 17:00:53 31TK4610_114
2010 TL

When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘MEMORY POSITION LINK’’ and
repeat the procedure again.
Multi-Inf ormation Display
110
09/07/29 17:00:58 31TK4610_115
2010 TL

Û
Ý
ÛÝ
ÛÝ
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. While ‘‘KEYLESS ACCESS SETUP’’
is shown, press the SEL/RESET
button to enter the customize mode. KEYLESS ACCESS BEEP KEYLESS ACCESS
LIGHT FLASH DOOR UNLOCK MODE
There are three custom settings for
the keyless access setup:
CONT INUED
On models with keyless access system
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
111
: Press the INFO button ( / ).
: Press the SEL/RESET button. Seepage112
.
Seepage113 .
Seepage114 .
09/07/29 17:01:09 31TK4610_116
2010 TL

Û
Ý Û
Ý Press the SEL/RESET button to see
the selections. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
You can choose this item to
customize f rom ‘‘KEYLESS ACCESS
SETUP’’ by pressing the INFO ( /
) button repeatedly. Select DRIVER DOOR or ALL
DOORS by pressing the INFO ( /
) button, then enter your selection
by pressing the SEL/RESET button. If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
UNLOCK MODE’’ and repeat the
procedure again.
Door Unlock Mode
Multi-Inf ormation Display
112
09/07/29 17:01:18 31TK4610_117
2010 TL