start stop button Acura TL 2010 Manual PDF

If you hold the engine start/stop
button for more than 7 seconds,
the starter motor, depending on
the outside temperature, runs f orabout10to25secondsuntilthe
engine starts.
Without touching the accelerator
pedal, push and release the engine
start/stop button. You do not need
to hold the engine start/stop
button to start the engine.
Depending on the outside
temperature, the starter motor
runs f or about 6 to 9 seconds until
the engine starts. The keyless access remote battery
becomes weak or dead. The keyless access remote system
main switch is of f .
In either of the f ollowing cases, you
should insert the keyless access
remote into the keyless remote slot.
For more inf ormation, see pages
and . If the engine does not start, wait at
least 10 seconds bef ore trying
again.
Your vehicle’s starting system has an
auto control mode. When you have
your keyless access remote and push
the engine start/stop button while
depressing the brake pedal (A/T) or
clutch pedal (M/T), this f eature
keeps the engine’s starter motor
running until the engine starts.
Follow these instructions to start the
engine:
Make sure the shif t lever is in
Park. Press on the brake pedal. Press the clutch pedal down all the
way. The power mode f rom ON to
START does not f unction unless
the clutch pedal is pressed. In cold weather, turn of f all
electrical accessories to reduce
the drain on the battery. Apply the parking brake.
1.
2.
3. 4.188 189Automatic transmission:
Manual transmission:
Starting the Engine (Models with Keyless Access System)
Driving
463
T he immobilizer system protects your
vehicle f rom thef t. If an improperly
coded keyless access remote (or other
device) is used, the engine’s f uel system
is disabled. For more inf ormation, see
page .
The engine is harder to start in cold
weather. Also, the thinner air f ound at
altitudes above 8,000 f eet (2,400
meters) adds to this problem. 143
09/07/29 18:18:19 31TK4610_468
2010 TL

If you cannot start the engine using
the normal engine start procedure,
do the f ollowing:Set the parking brake.
If there is a problem with the
starting system, you will see a
‘‘CHECK STARTING SYSTEM’’
message on the multi-inf ormation
display with the power mode ON.
You will also see this message when
the auto control mode of the starting
system has a problem. If this message is on, you should
press and hold the engine start/stop
button until the engine starts. The
engine start/stop button can be
pressedupto15seconds.
Even though you may be able to
start the engine manually without
the auto control mode of the starting
system, have your vehicle inspected
by a dealer.
Your vehicle has the engine start/
stop button instead of an ignition
switch to select the power mode. For
more information, see page .
Do not f ollow this procedure unless
it is a case of emergency. Even if you
can start the engine using this
method, the system may have a
malf unction. Contact your dealer as
soon as possible.Press and hold the engine start/
stop button f or about 15 seconds
while pressing the brake pedal
(automatic) or the clutch pedal
(manual). Press the engine start/stop button
to turn on the ACCESSORY mode. Put the shif t lever into Park.
178 1.
2.
3.
4.
Automatic transmission:
Starting the Engine (Models with Keyless Access System)
Emergency Engine Start
Check Starting System Message
464
09/07/29 18:21:03 31TK4610_469
2010 TL

Press the clutch pedal, and shif t to
reverse.
The manual transmission has a
lockout so you cannot accidentally
shif t f rom any f orward gear to
reverse while the vehicle is moving
at a certain speed. If you cannot shif t
to reverse when the vehicle is
stopped, do the f ollowing:
With the clutch pedal pressed,
move the shift lever to the first/
second gear side of the neutral
gate, then shif t to reverse.If you are still unable to shif t to
reverse, apply the parking brake,
and select the ACCESSORY or
VEHICLE OFF (LOCK) mode
(see page ).
With the clutch pedal still pressed
f ully, press the engine start/stop
button to start the engine.
If you need to use this procedure to
shif t to reverse, your vehicle may be
developing a problem. Have it
checked by your dealer.
1. 2.
3.
4.
179
Reverse Lockout
Manual T ransmission
Driving
467
Move the shift lever in sequence.
09/07/29 18:21:30 31TK4610_472
2010 TL

Î
Î
These indicators between the
tachometer and speedometer show
which position the shif t lever is in. Using a paddle shif t mode, the gear
position indicator shows you the
selected gear number (see page
).
The ‘‘D’’ indicator comes on f or a
f ew seconds when you turn the
ignition switch to the ON (II)
position. If it f lashes while driving (in
any shif t position), it indicates a
possible problem in the transmission. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If the malf unction indicator lamp
comes on along with the ‘‘D’’
indicator, there is a problem with the
automatic transmission control
system. Avoid rapid acceleration and
have the transmission checked by
your dealer as soon as possible.
When the ‘‘D’’ indicator warns of a
possible problem with the
transmission, you will see a ‘‘CHECK
TRANSMISSION’’ message on the
multi-inf ormation display. :
178 181
473
Shif t L ever Position Indicators
Automatic Transmission
468
GEAR POSITION INDICATOR on
PADDLE SHIFT MODE
09/07/29 18:21:40 31TK4610_473
2010 TL

µ
Î
Î
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Press the release
buttononthefrontof theshiftlever
to move it.
To shif t f rom Park to any position,
pressfirmlyonthebrakepedal,and
pressthereleasebuttononthefront
of the shift lever, then move the
lever. You cannot shift out of Park
when the ignition switch is in the
LOCK (0) or ACCESSORY (I)
position. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. VEHICLE
OFF (LOCK) Mode is the
equivalent of LOCK (0) and
ACCESSORY Mode is the
equivalent of ACCESSORY (I).
For more inf ormation, see pages
and .
178
:
181
Do this:
Press the brake pedal and
press the shift lever release
button.
Press the shift lever release
button.
Move the shift lever.
To shift from:
PtoR
RtoP
NtoR DtoS
StoD
DtoN
NtoD RtoN
CONT INUED
Shif ting
Park (P)
Automatic Transmission
Driving
469
RELEASE BUTTON
09/07/29 18:21:50 31TK4610_474
2010 TL

µ
µ µ
If you have done all of the above and
still cannot move the lever out of
Park, see on
page . Press the brake
pedal and the release button on the
frontoftheshiftlevertoshiftfrom
Park to reverse. To shif t f rom
reverse to neutral, come to a
completestop,andthenshift.Press
the release button bef ore shif ting
into reverse f rom neutral.
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from neutral to
another gear. Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear (1 through 5) f or your
speed and acceleration. You may
notice the transmission shifting up at
higher engine speeds when the
engine is cold. This helps the engine
warm up f aster.
You must also press the release
button to shift into Park. To avoid
transmission damage, come to a
complete stop bef ore shif ting into
Park.
TheshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
TheshiftlevermustbeinPark
bef ore you change the power mode
f rom ON to VEHICLE OFF (LOCK). 471
On models with keyless access system
On models without keyless access
system
Shif t L ock Release Reverse (R)
Neutral (N) Drive (D)
Automatic Transmission
470
09/07/29 18:21:59 31TK4610_475
2010 TL

´µ
When you move the shif t lever f rom
‘‘D’’ to ‘‘S’’ position and pull either
paddle shif ter, the gear position
indicator displays ‘‘M’’ along with the
selected gear number.
To upshif t, pull the (right) paddle
shif ter. To downshif t, pull the
(lef t) paddle shif ter. When you accelerate f rom a stop,
the transmission starts in f irst gear,
and you must manually upshif t
between f irst and f if th gears. Make
sure you upshif t bef ore the engine
speed reaches the tachometer’s red
zone.
With the shif t lever in the S position,
you can manually shif t up or down
with the paddle shifters. The
transmission goes into the sequential
shif t mode and holds the selected
gear.
To enter the sequential shif t mode,
pressthereleasebuttononthefront
of the shift lever, move the lever to
the S position, then pull either paddle
shif ter. To return to drive mode (D),
move the shif t lever to the D position.
While you are driving in the
sequential shif t mode, the
transmission will not automatically
return to drive mode (D).
CONT INUED
Using the Paddle Shif ters in the S
position (Sequential Shif t Mode)
Driving with the Paddle Shif ters (A utomatic Transmission Only)
Driving
475
‘‘M’’ INDICATOR
GEAR POSITION INDICATOR
09/07/29 18:22:52 31TK4610_480
2010 TL

Î
Î
The vehicle stability assist (VSA)
system helps to stabilize the vehicle
during cornering if the vehicle turns
more or less than desired. It also
assists you in maintaining traction
while accelerating on loose or
slippery road surf aces. It does this
by regulating the engine’s output,
and by selectively applying the
brakes.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. There may also
be some noise f rom the VSA
hydraulic system. You will also see
the VSA activation indicator blink.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety. When VSA is off, the VSA off
indicator comes on as a reminder.
When VSA activates, you will see the
VSA system indicator blink.
If this indicator comes on while
driving, you will also see a ‘‘CHECK
VSA SYSTEM’’ and/or ‘‘CHECK
HILL START ASSIST SYSTEM’’
message on the multi-inf ormation
display. Drive cautiously as the VSA
may not be f unctioning. Without
VSA, your vehicle will have normal
braking and cornering ability, but it
will not have VSA traction and
stability enhancement. Also, the VSA
OFF switch will not operate. Pull to
the side of the road when it is saf e,
and turn of f the engine. Reset the
system by restarting the engine. If
the VSA system indicator stays on,have the VSA system inspected by
your dealer.
If the indicator does not come on
when the ignition switch is turned
to the ON (II) position, there may be
a problem with the VSA system.
Have your dealer inspect your
vehicle as soon as possible.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
The main f unction of the
VSA system is generally known as
Electronic Stability Control (ESC).
The system also includes a traction
control f unction. :
178 181
Vehicle Stability Assist
(VSA ) System Indicator VSA Of f Indicator
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
484
NOTE:
09/07/29 18:24:26 31TK4610_489
2010 TL

Î Each tire pressure is shown in PSI
(U.S. models) or in kPa (Canadian
models).If any of the tires has low pressure,
thetirepressuremonitoralsoshows
the above message and each tire
pressure to warn you about the low
tire pressure when you select the
displaybypressingtheINFObutton
several times.
Each tire has its own pressure
sensor. If the air pressure of a tire
becomes signif icantly low, the
sensor in that tire immediately sends
a signal that causes the low tire
pressure/TPMS indicator in the
instrument panel to come on. If this
happens, you will see which tire is
losing pressure on the multi-
inf ormation display along with a
‘‘CHECK TIRE PRESSURE’’
message.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
:
178 181
Tire Pressure Monitoring System (TPMS)
490
Canadian model U.S. model Canadian model
09/07/29 18:25:27 31TK4610_495
2010 TL

Î
Î
CONT INUED
Your vehicle displays engine oil lif e
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perf orm engine oil
replacement and indicated
maintenance service.To see the current engine oil lif e
displayed on the multi-inf ormation
display, turn the ignition switch to
the ON (II) position, and press the
SEL/RESET button on the steering
wheel repeatedly until the engine oil
lif e is displayed. Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
Based on the engine operating
conditions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e and displays it as a
percentage. :
178 181
Maintenance Minder
Engine Oil L if e Indicator
Maint enance
497
REMAINING ENGINE OIL LIFE
U.S. model is shown.
09/07/29 18:26:24 31TK4610_502
2010 TL