change time Acura TL 2010 Owner's Manual

µ
You’ll f ind many saf ety
recommendations throughout this
section, and throughout this manual.
Therecommendationsonthispage
are the ones we consider to be the
most important.
A seat belt is your best protection in
all types of collisions. Airbags are
designed to supplement seat belts,
not replace them. So even though
your vehicle is equipped with airbags,
make sure you and your passengers
always wear your seat belts, and
wear them properly (see page ).
Children age 12 and under should
ride properly restrained in a back
seat, not the front seat. Infants and
smallchildrenshouldberestrained
in a child seat. Larger children
should use a booster seat and a lap/
shoulder belt until they can use the
belt properly without a booster seat (see pages ).
While airbags can save lives, they
can cause serious or fatal injuries to
occupants who sit too close to them,
or are not properly restrained.
Inf ants, young children, and short
adults are at the greatest risk. Be
sure to f ollow all instructions and
warnings in this manual.
Alcohol and driving don’t mix. Even
one drink can reduce your ability to
respond to changing conditions, and
your reaction time gets worse with
every additional drink. So don’t drink
and drive, and don’t let your f riends
drink and drive, either.
Engaging in mobile phone
conversation or other activities that
keep you f rom paying close attentionto the road, other vehicles and
pedestrians could lead to a crash.
Remember, situations can change
quickly, and only you can decide
when it is saf e to divert attention
away f rom driving.
Having a tire blowout or a
mechanical f ailure can be extremely
hazardous. To reduce the possibility
of such problems, check your tire
pressures and condition f requently,
and perform all regularly scheduled
maintenance (see page ). Excessive speed is a major f actor in
crash injuries and deaths. Generally,
the higher the speed, the greater the
risk, but serious injuries can also
occur at lower speeds. Never drive
f aster than is saf e f or current
conditions, regardless of the
maximum speed posted.
16 37 56
497
Important Saf ety Precautions
Always Wear Your Seat Belt
Restrain All ChildrenBe Aware of Airbag Hazards
Don’t Drink and Drive
Pay Appropriate Attention to the
Task of Driving Saf ely
K eep Your Vehicle in Saf e
Condition Control Your Speed
6
09/07/29 16:43:19 31TK4610_011
2010 TL

Î
Î
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see pages and ).
Replace the bulb as soon as possible,
since other drivers cannot see that
you are signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash. This indicator normally comes on
when you turn the ignition switch to
the ON (II) position and goes of f
af ter the engine starts. If it comes on
at any other time, there is a problem
in the electric power steering system.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand . If this happens, stop the vehicle in a
saf e place and turn of f the engine.
Reset the system by restarting the
engine. The indicator will stay on,
but should go of f af ter driving a
short distance. If it does not go of f ,
or comes back on again while driving,
take the vehicle to your dealer to
have it checked. With the indicator
on, the EPS may be turned of f ,
making the vehicle harder to steer.
If you turn the steering wheel to the
f ull lef t or right position repeatedly
while stopping or driving at very low
speed, you may f eel slightly harder
steering in order to prevent damage
to the steering box caused by
overheating.
You will also see a ‘‘CHECK POWER
STEERING SYSTEM’’ message on
the multi-information display.
:
181
178
524 528
Instrument Panel Indicators
Turn Signal and
Hazard Warning
Indicators
Electric Power Steering
(EPS) Indicator
70
09/07/29 16:54:18 31TK4610_075
2010 TL

ÎÎ
Î
ÛÝ
Î
ÛÝ
These messages go of f af ter several
seconds.
With the ignition switch in the ON
(II) position, the multi-inf ormation
display changes as shown on pageeach time you press the INFO
( / ) button or the SEL/RESET
button.
When you turn the ignition switch
to the ON (II) position, your last
selection is displayed.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pages
and .
If you do not f asten your seat belt,
you will also see a ‘‘FASTEN SEAT
BELT’’ message on the multi-
inf ormation display when you turn
the ignition switch to the ON (II)
position.
These messages go of f several
seconds af ter the key is inserted into
the ignition switch. 80
:
178 181
On models with keyless access system
Multi-Inf ormation Display
78
SEL/RESET BUTTON
INFO BUTTONS ( / )
A/T model is shown.
09/07/29 16:55:36 31TK4610_083
2010 TL

The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial/
territorial regulations to disconnect,
reset, or alter the odometer with the
intent to change the number of miles
or kilometers indicated.This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. There
are two trip meters: Trip A and Trip
B. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
To reset a trip meter, display it, and
then press and hold the SEL/RESET
button until the number resets to
‘‘0.0.’’When you reset Trip A, average f uel
economy A, average vehicle speed A,
and elapsed time A are reset at the
same time. When you reset Trip B,
average fuel economy B, average
vehicle speed B, and elapsed time B
are reset.
In the customizing mode, you can set
Trip A and average f uel economy A
to reset at the same time when you
ref uel your vehicle (see page ).
102
CONT INUED
Multi-Inf ormation Display
Odometer T rip Meter
Inst rument s and Cont rols
81
TRIP METER A
Canada
U.S. U.S.
Canada
TRIP METER B
ODOMETER
09/07/29 16:56:06 31TK4610_086
2010 TL

Î
ÎThis shows your instant f uel
economy.
This shows the time passed traveled
since you last reset it. When you turn
the ignition switch to the ON (II)
position, ELAPSED TIME A or B is
reset.
Models equipped with the
keyless access system have an
engine start/stop button instead
of an ignition switch. ON Mode
is the equivalent of ON (II). For
more inf ormation, see pagesand .
This shows your vehicle’s average
f uel economy in mpg (U.S. models)
or liter/100 km (Canadian models)
since you last reset Trip A or Trip B.
You can customize the Trip A and
AVG. FUEL A reset condition on the
multi-inf ormation display (see page
).
This shows the average speed you
are traveling in miles per hour (mph)
forU.S.modelsorkilometersper
hour (km/h) f or Canadian models. This shows the estimated distance
you can travel on the fuel remaining
in the f uel tank. This distance is
estimated f rom the f uel economy
you received over the last several
miles (U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traf f ic, etc.
:
178
102
181
INST . MPG (U.S. models)/INST . L /100 km (Canadian models)
EL A PSED T IME A /B
AVG. FUEL A/B
A VG. SPEED A /B RANGE
Multi-Inf ormation Display
Inst rument s and Cont rols
83
09/07/29 16:56:29 31TK4610_088
2010 TL

Î
Î
Î
Î
Î
Î
Î
Î
Î
Description
Setting Option
Menu Item
CONT INUED
Group Setup Page
Changes which doors unlock when you use the
remote or grab the driver’s door handle.
Causes some exterior lights to blink when you
unlock/lock the doors by grabbing or touching the
sensor/pushing the button on the driver’s door
handle.
Causes the beeper to sound when you unlock/lock
the doors by grabbing or touching the sensor/
pushing the button on the driver’s door handle.
Changes how long (in seconds) the interior lights
stay on after you close the doors.
Changes how long (in seconds) the exterior lights
stay on after you close the driver’s door.
Changes the timing of when the headlights come
on. The headlight switch needs to be in the AUTO
position.15 sec
0sec
LOW
MIN
DRIVER DOOR
ALL DOORS
ON
OFF
ON
OFF
60 sec
30 sec
60 sec
30 sec
15 sec
MAX
HIGH
MID
DOOR UNLOCK MODE
KEYLESS ACCESS LIGHT
FLASH
KEYLESS ACCESS BEEP
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT
AUTO OFF TIMER
AUTO LIGHT
SENSITIVITY
KEYLESS ACCESS
SETUP
(P.111)
LIGHTING SETUP
(P.116)
112
113
114
117
118
119
1:
2: Default setting
Only on models with keyless access system1
1
1
1
1
1
2
Multi-Inf ormation Display
Inst rument s and Cont rols
95
09/07/29 16:58:37 31TK4610_100
2010 TL

Î
Î Î
Î
Î
Î
Î
Î
Î
Page
Description
Menu Item
Group Setup Setting Option
122
123
125
126
127
129
Changes when the doors automatically lock.
Changes when the doors automatically unlock.
Changes which doors unlock with the remote
transmitter/keyless access remote on the first
push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Set/Cancel all the customized settings as default.
AUTO DOOR LOCK
AUTO DOOR UNLOCK
KEY AND REMOTE
UNLOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMER
DOOR/WINDOW
SETUP
(P.121)
DEFAULT ALL
(P.129) SHIFT FROM P (A/T only)
WIT H VEHICLE SPEED
OFF
SHIFT TO P/DRIVER
DOOR (A/T only)
SHIFT TO P/ALL DOORS
(A/T only)
IGN OFF/DRIVER DOOR
IGN OFF/ALL DOORS
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 sec
60 sec
30 sec
CANCEL
SET
Default setting
1:
2:
3: Default setting for automatic transmission
Default setting for manual transmission1
2 3
1
1
1
Multi-Inf ormation Display
96
09/07/29 16:58:44 31TK4610_101
2010 TL

ÛÝÛ
Ý
ÛÝ
Î
Î
You can customize some of the
vehicle control settings to your
pref erence. Here are the settings
you can customize: METER SETUP
When you want to change the
vehicle control settings, press the
INFO ( / ) button to select CHG
SETTING, then press the SEL/
RESET button. Each time you press the INFO ( /
) button, the screen changes as
shownonthenextpage.Pressthe
INFO( / )buttonuntilyousee
the setup you want to customize,
then press the SEL/RESET button
to enter your selection.
If you do not make any changes,
select ‘‘EXIT.’’ The display returns to
the normal display.
DOOR/WINDOW SETUP LIGHTING SETUP
If you want the settings as they were
when the vehicle lef t the f actory,
select DEFAULT ALL, as described
on page .
POSITION SETUP
KEYLESS ACCESS SETUP
: Only on models with keyless
access system
129
CONT INUED
Customize Settings
Multi-Inf ormation Display
Inst rument s and Cont rols
97
09/07/29 16:58:57 31TK4610_102
2010 TL

ÛÝ
ÛÝ
Û
Ý
ÛÝ
Press the SEL/RESET button to see
the selections.
Select the desired language by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
There are three language selections
you can make: English, French, and
Spanish. To choose the language you
want, f ollow these instructions:
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
While ‘‘METER SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
Language Selection
Multi-Inf ormation Display
100
09/07/29 16:59:26 31TK4610_105
2010 TL

ÛÝÛÝ
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions:
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the setting.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘LANGUAGE SELECTION’’ and
repeat the procedure again.
The displayed number is the current
adjustment above or below the
outside temperature.
Adjust the outside temperature value
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET
button to set the desired value.
Adjust Outside Temp. Display
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
101
Canadian models
U.S. models
09/07/29 16:59:39 31TK4610_106
2010 TL