stop start Acura TL 2012 Manual Online

µ
Î
This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Press the release
buttononthefrontof theshiftlever
to move it.
To shif t f rom Park to any position,
pressfirmlyonthebrakepedal,and
pressthereleasebuttononthefront
of the shift lever, then move the
lever. You cannot shift out of Park
when the ignition switch is in the
LOCK (0) or ACCESSORY (I)
position.Do this:
Press the brake pedal and
press the shift lever release
button.
Press the shift lever release
button.
Move the shift lever.
To shift from:
PtoR
RtoP
NtoR DtoS
StoD
DtoN
NtoD RtoN
CONT INUED
Shif ting Park (P)
Automatic Transmission
Driving
495
RELEASE BUTTON
11/01/14 19:21:11 31TK4630_500
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. VEHICLE
OFF (LOCK) Mode is the equivalent of
LOCK (0) and ACCESSORY Mode is the
equivalent of ACCESSORY (I). For more
information, see pages 184 and 187.
:
If you have done all of the above and
still cannot move the lever out of
Park, see
on
page . 497Shif t L ock Release
2012 TL

µ
µ µ
Press the brake
pedal and the release button on the
frontoftheshiftlevertoshiftfrom
Park to reverse. To shif t f rom
reverse to neutral, come to a
completestop,andthenshift.Press
the release button bef ore shif ting
into reverse f rom neutral.
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from neutral to
another gear.
You must also press the release
button to shift into Park. To avoid
transmission damage, come to a
complete stop before shifting
into Park.
TheshiftlevermustbeinPark
bef ore you can remove the key f rom
the ignition switch.
TheshiftlevermustbeinPark
bef ore you change the power mode
f rom ON to VEHICLE OFF (LOCK).
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear (1 through 6 gear) to
keep the engine at the best speed f or
the driving conditions.
On models with keyless access system
On models without
keyless access system
Reverse (R)
Neutral (N) Drive (D)
Automatic Transmission
496
11/01/14 19:21:19 31TK4630_501
Driving
2012 TL

The automatic transmission will not
allow you to shif t up or down if :If the vehicle speed decreases
below the redline of the selected
lowergearwhiletheindicatoris
f lashing, the transmission
downshif ts, and the indicator
displays the selected gear.
You upshif t bef ore the engine
speed reaches the lowest
threshold of the higher gear.
You pull both paddle shif ters at
thesametime. You downshif t bef ore the engine
speed reaches the highest
threshold of the lower gear.
If you try to do this, the gear
position indicator will f lash the
numberof thelowergearseveral
times, then return to a higher gear.
Downshifting with the paddle shifter
allows you to increase the engine
braking when going down steep or
long hills, and provides more power
when climbing uphills. You can
upshif t the transmission manually to
reduce the rpm.
When you accelerate f rom a stop,
the transmission starts in f irst gear,
and shif ts f rom f irst to second
automatically. You must manually
upshif t between second and sixth
gears. Make sure you upshif t bef ore
the engine speed reaches the
tachometer’s red zone.
The transmission remains in the
selectedgear(6,5,4,3,or2).There
is no automatic downshif t when you
push the accelerator pedal to the
f loor.
When you are driving, the
transmission downshifts to the lower
gear under the f ollowing conditions:
The vehicle slows down to a
certain speed.
You press the brake pedal.
The vehicle detects that you are
driving uphill or downhill. The transmission also shif ts
automatically as the vehicle comes to
a complete stop. It downshif ts to f irst
gear when the vehicle speed reaches
6mph(10km/h)orless.
Driving with the Paddle Shif ters (A utomatic Transmission Only)
502
11/01/14 19:22:29 31TK4630_507
Driving
2012 TL

´
When you are in sequential shif t
mode, and the vehicle is stopped,
pull the (right) paddle shifter to
shif t to second gear. You will see
‘‘M2’’ in the display. Starting in
second gear helps to reduce
wheelspin in deep snow or on a
slippery surf ace. Drive in the highest gear that lets
the engine run and accelerate
smoothly. This will give you good
f uel economy and ef f ective
emissions control. The f ollowing
shif t points are recommended:
Normal acceleration15 mph (24 km/h)
25 mph (40 km/h)
40 mph (64 km/h)
45 mph (72 km/h)
50 mph (81 km/h)
Shif t up
1st to 2nd
2nd to 3rd 3rd to 4th4th to 5th
5th to 6th
Driving with the Paddle Shif ters (A utomatic Transmission Only)
St art ing in Second Gear Recommended Shif t Point s
Driving
503
11/01/14 19:22:37 31TK4630_508
2012 TL

The vehicle stability assist (VSA)
system helps to stabilize the
vehicle during cornering if the
vehicle turns more or less than
desired. It also assists you in
maintaining traction while
accelerating on loose or slippery
road surfaces. It does this by
regulating the engine’s output, and
by selectively applying the brakes.
The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.When VSA is off, the VSA OFF
indicator comes on as a reminder.
When VSA activates, you will see the
VSA system indicator blink.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. There may also
be some noise f rom the VSA
hydraulic system. You will also see
the VSA system indicator blink. The main f unction of the
VSA system is generally known as
Electronic Stability Control (ESC).
The system also includes a traction
control f unction.
If this indicator comes on while
driving, you will also see a ‘‘CHECK
VSA SYSTEM’’ and/or ‘‘CHECK
HILL START ASSIST SYSTEM’’
message on the multi-inf ormation
display. Drive cautiously as the VSA
may not be f unctioning. Without
VSA, your vehicle will have normal
braking and cornering ability, but it
will not have VSA traction and
stability enhancement. Also, the VSA
OFF switch will not operate. Pull to
the side of the road when it is saf e,
and turn of f the engine. Reset the
system by restarting the engine. If
the VSA system indicator stays on, have the VSA system inspected by
your dealer.
If there is a problem with the hill
start assist system, the VSA system
indicator comes on and stays on. The
multi-inf ormation display shows a
‘‘CHECK HILL START ASSIST
SYSTEM’’ message.
With the VSA system indicator on,
you may not be able to stop the
engine even if you park the vehicle
saf ely. To stop the engine, see
on
.
On models with SH-AWD
On models with keyless access system
Vehicle Stability Assist
(VSA ) System IndicatorVSA OFF Indicator
Emergency Engine Stop
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
510
NOTE:
11/01/14 19:23:49 31TK4630_515
page 192
Driving
2012 TL

VSA is turned on every time you
start the engine, even if
you turned it off the last time
you drove the vehicle.
In certain unusual conditions when
your vehicle gets stuck in shallow
mud or f resh snow, it may be easier
to free it with the VSA temporarily
switched of f . When the VSA system
is of f , the traction control system is
alsooff.Youshouldonlyattemptto
f ree your vehicle with the VSA of f if
you are not able to f ree it when the
VSA is on.
Immediately af ter f reeing your
vehicle, be sure to switch the VSA on
again. We do not recommend driving
your vehicle with the VSA and
traction control systems switched off.Driving with varying tire or wheel
sizes may cause the VSA to
malf unction. When replacing tires,
make sure they are of the same size
and type as your original tires (see
page ).
If you install winter tires, make sure
they are the same size as those that
were originally supplied with your
vehicle. Exercise the same caution
during winter driving as you would
Your vehicle is equipped with a hill
start assist f eature to help prevent
the vehicle f rom rolling on inclines
as you move your f oot f rom the
brake pedal to the accelerator.
To activate hill start assist, you must
come to a complete stop and make
sure the shif t lever is either in D or S
when f acing uphill, or reverse when
f acing downhill. This f eature begins
working a few seconds after you are
in the correct gear position. Release
thebrakepedal.Thebrakesremain
engaged brief ly to keep the vehicle
f rom rolling f orward or backward.
Gently apply the accelerator pedal as
in normal driving. Hill start assist will
release brake pressure gradually as
you accelerate.
574
On models with SH-AWD
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
VSA and Tire Sizes
Hill Start Assist
512
11/01/14 19:24:09 31TK4630_517
if your vehicle was not equipped
wiht VSA.
Driving
2012 TL

Hillstartassistmaynotpreventyour
vehicle f rom rolling downhill on a
very steep or slippery slope, and will
not operate on small inclines.
Hill start assist is not a replacement
f or the parking brake. If parking
your vehicle, ensure that the
transmission is in park, and/or the
parking brake is f ully applied bef ore
exiting the vehicle. For vehicles with
manual transmission, it is
recommended that you turn of f the
engine bef ore exiting the vehicle.If the VSA system indicator comes
on with a ‘‘CHECK HILL START
ASSIST SYSTEM’’ message on the
multi-inf ormation display, there may
be a problem with the hill start assist.
The VSA also may not f unction.
Have your vehicle inspected by your
dealer.
Hill start assist will still operate even
when VSA is switched off.
On manual transmission models:
You must come to a complete stop,
press the clutch pedal, and shif t to
f irst gear when f acing uphill, or
reverse when f acing downhill.
Release the brake pedal. The brakes
remain engaged brief ly to keep the
vehicle f rom rolling f orward or
backward while you move your f oot
f rom the brake pedal to the
accelerator pedal. Gently apply the
accelerator pedal while
simultaneously releasing the clutch
pedal, as in normal driving. Hill start
assist will release brake pressure
gradually as you accelerate.
Hill start assist will also hold braking
brief ly if you select the neutral gear
position with the clutch pedal
depressed when f acing uphill.
Vehicle Stability A ssist (VSA), aka Electronic Stability Control (ESC), System
Driving
513
11/01/14 19:24:17 31TK4630_518
2012 TL

Your vehicle is equipped with a tire
pressure monitoring system (TPMS)
that turns on every time you start the
engine and monitors the pressure in
your tires while driving.If you think you can saf ely drive a
short distance to a service station,
proceed slowly to the station, then
inflate the tire to the recommended
pressure shown on the driver’s
doorjamb.
If the tire is f lat, or if the tire
pressure is too low to continue
driving, replace the tire with the
compact spare tire (see page ).
Driving on a signif icantly under-
inf lated tire causes the tire to
overheat and can lead to tire failure.
Under-inf lation also reduces f uel
efficiency and tire tread life, and may
af f ect the vehicle’s handling and
stopping ability.
Becausetirepressurevariesby
temperature and other conditions,
the low tire pressure/TPMS
indicator may come on unexpectedly.
When the low tire pressure/TPMS
indicator is on, one or more of your
tires is significantly underinflated.
You should stop and check your
tires as soon as possible, and inflate
them to the proper pressure
as indicated on the vehicle’s tire
information placard.
Each tire has its own pressure
sensor (not including the spare tire).
If the air pressure of a tire becomes
signif icantly low, the sensor in that
tire immediately sends a signal that
causes the low tire pressure/TPMS
indicator in the instrument panel to
come on. If this happens, you will see
which tire is losing pressure on the
multi-inf ormation display along with
a ‘‘CHECK TIRE PRESSURE’’
message. It is possible that the pressures
shown on the multi-inf ormation
display and the pressures you
manually measure are slightly
dif f erent.
If the dif f erence is signif icant or you
cannot make the low tire pressure/
TPMS indicator and message on the
multi-inf ormation display go out af ter
inf lating the tires to the specif ied
values, have your dealer check the
system as soon as possible. 583
Low Tire Pressure/
TPMS Indicator
Tire Pressure Monitoring System (TPMS)
514
11/01/14 19:24:27 31TK4630_519
Driving
2012 TL

Î
Although your tire pressure is
monitored, you must manually check
thetirepressuresmonthly.
Each tire, including the spare, should
be checked monthly when the
vehicle is cold, and set to the
recommended inflation pressure as
specified on the vehicle placard and
in the owner’s manual (see).
For example, if you check and f ill
your tires in a warm area, then drive
in extremely cold weather, the tire
pressure will be lower than
measured and could be underinf lated
and cause the low tire pressure/
TPMS indicator to come on. Or, if
youcheckandadjustyourtire
pressure in cooler conditions, and
drive into extremely hot conditions,
the tire may become overinf lated.
However, the low tire pressure/
TPMS indicator will not come on if
thetiresareoverinflated.
Refer to page for tire inflation
guidelines.
If there is a problem with the TPMS,
this indicator begins to f lash. It stops
flashing after approximately 1
minute, then stays on. You will also
see a ‘‘CHECK TPMS SYSTEM’’
message on the multi-inf ormation
display (see page ). Toselectthetirepressuremonitor,
press the INFO button several times
with the ignition switch in the ON
(II) position or with the power mode
ON.
You will see the above display on the
multi-inf ormation display when each
tire pressure is normal.
517
568
CONT INUED
Tire Pressure Monitor
Tire Pressure Monitoring System (TPMS)
Driving
515
U.S.
Example: Technology Package is shown.
11/01/14 19:24:39 31TK4630_520
page 570
ÎModels equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode

is the equivalent of ON (II). For more
information, see page s 184 and 187.
:
2012 TL

ÎÎ
To turn the system off, press and
hold the BSI OFF button when the
ignition switch is in the ON (II)
position. The BSI indicator on the
instrument panel glows amber,
indicating that the system is turned
of f . The multi-inf ormation display
indicates that the system is of f .To turn the system on again, press
and hold the same button. The BSI
indicator on the instrument panel
turns off. The multi-information
display indicates that the system is
on.
When the ignition switch is turned
to the ON (II) position, the system
will be in the previously selected ON
or OFF setting.
Blind Spot Inf ormation System (BSI)
BSI OFF Button
Driving
525
U.S. model is shown.
Canadian model is shown.
11/01/14 19:26:13 31TK4630_530
Î
Models equipped with the keyless access
system have an engine start/stop button
instead of an ignition switch. ON Mode
is the equivalent of ON (II). For more
information, see
page s 184 and 187.
:
2012 TL