ECO mode Acura TSX 2004 User Guide

When the remote transmitter’s
battery begins to get weak, it may
take several pushes on the button to
lock or unlock the doors, and the
LED will not light. Replace the
battery as soon as possible.
Panic mode allows you to remotely
activate your car’s horn and exterior
lights to attract attention. The horn
sounds and the exterior lights f lash
f or about 30 seconds. To activate
panic mode, press and hold the
PANIC button f or about two seconds.
To cancel Panic mode bef ore 30
seconds, press any button on the
remote transmitter. You can also
turn the ignition switch to ON (II).
Panic mode will not activate if the
ignition switch is in the ON (II)
position.
To replace the battery, place a cloth
on the edge of the transmitter and
remove the upper half by carefully
prying on the edge with a small f lat-
tip screwdriver.
Battery type: CR2025
CONT INUED
Replacing the Battery
Panic Mode
Keys and Locks
Inst rument s and Cont rols85

Pressing the OFF button shuts the
climate control system completely
off. No air flow can cause the
windows to fog up. It is
recommended that you keep the f an
on at all times so stale air and
moisture do not build up in the
interior and cause f ogging.
When you set the temperature to its
lower limit ‘‘ ’’ or its upper
limit ‘‘ ’’, the system runs at
f ull cooling or heating only. It does
not regulate the interior temperature.
When the temperature is set
between the lower and upper limits,
the system regulates the interior
temperature to the set value.
In cold weather, the f an will not
come on automatically until the car
has been driven f or a short time and
the heater starts to develop warm air. You can manually select various
f unctions of the Climate Control
system when it is in f ully automatic
mode. All other f eatures remain
automatically controlled. Some of
these functions appear in the
Navigation System display. Press the
A/C button under the display to
show these functions. Making any
manual selection causes the
indicator in the AUTO button to go
out. Semi-automatic Operation
Climat e Cont rol Syst em
Comf ort and Convenience Feat ures122

µIf you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
To activate Auto Select, press the
A. SEL button. A. SEL will f lash in
the display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset buttons. You
can then use the preset buttons to
select those stations.
If you are in a remote area, Auto
Select may not f ind six strong AM
stations or twelve strong FM stations.
If this happens, you will see a ‘‘0’’
displayed when you press any preset
button that does not have a station
stored. AUTO SELECT
Audio System
Comf ort and Convenience Feat ures132
AM/FM BUTTON A. SEL INDICATOR A. SEL BUTTON
SEEK
BAR
SCAN
BUTTON
PRESET BUTTONS

µ
µ
These two
modes adjust the strength of the
sound coming f rom each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the f ront-to-back
strength. For inf ormation, see page .
Bass, Treble, Balance, and Fader are
each adjustable. You select which of
these you want to adjust by pressing
the TUNE/SOUND knob. The mode
changes from BAS to TRE to FAD to
BAL,andthenbacktotheselected
audio mode, each time you press the
TUNE/SOUND knob.
Select BAL or FAD by pressing the
TUNE/SOUND knob. Adjust the
Balance or Fader to your liking by
turning the knob.
The displayed number shows you
the current setting.
When the adjustment level reaches
the center, you will see ‘‘ ’’.The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode with the TUNE/
SOUND knob.
Use these modes to
adjust the tone to your liking. Select
TRE or BAS by pressing the TUNE/
SOUND knob. Adjust the desired
mode by turning the knob.
The displayed number shows you
the current setting.
When the adjustment level reaches
the center, you will see ‘‘ ’’.
154
Adjusting the Sound
Balance/Fader
Radio Frequencies and Reception
Treble/Bass
Audio System
Comf ort and Convenience Feat ures134
ADJUSTMENT LEVEL
TUNE/SOUND
KNOB

µµ
When that disc ends, the next disc in
the CD changer is loaded and played.
Af ter the last disc f inishes, the
system returns to disc one. Each time you press and
release it, the system skips forward
to the beginning of the next track.
Press and release to skip
backward to the beginning of the
current track. Press and release it
again to skip to the beginning of the
previous track. To move rapidly within a track, press
andholdtheleftorrightsideof the
SKIP bar. You will hear a beep and
the system will continue to move.
Press to move f orward, or
to move backward. Release the
bar when the system reaches the
point you want.
Select the CD changer by pressing
the CD button. You will see ‘‘CD’’ in
the display. The system will begin
playing the last selected disc in the
CD changer. You will see the disc
and track numbers displayed.
To select a dif f erent disc, press the
appropriate Preset button (1 6). If
youselectanemptypositioninthe
CD changer, the system will go into
the loading sequence (see page ).
You can use the SKIP bar while a
disc is playing to select passages and
change tracks. This f eature, when
activated, samples all the tracks on
the selected disc in the order they
are recorded on the CD. To activate
the Scan f eature, select the Scan
mode by pressing the SCAN button.
You will see SCAN in the display.
The system will then play the first
track f or about 10 seconds. If you do
nothing, the system will then play
the f ollowing tracks f or 10 seconds
each. When it plays a track that you
want to continue listening to, press
the SCAN button again.
158
CONT INUED
Operat ion
Audio System
Comf ort and Convenience Feat ures
SCAN
139

To take the system out of CD mode,
press the AM/FM button. Each time
you press the AM/FM button, the
system will change to the next mode;
FM1, FM2, or AM. When you return
to CD mode by pressing the CD
button, play will continue at the same
point that it lef t of f .
If you turn the system of f while a CD
is playing, either with the PWR/VOL
knob or the ignition switch, play will
continue at the same point when you
turn it back on.
When activated, Disc Scan plays
about 10 seconds of the f irst track of
each CD in the order they are stored
in the CD changer. To activate Disc
Scan, press and hold the SCAN
button until you see D-SCAN in the
display.
If you do nothing, the system will
then play the next CD’s first track.
When it plays a disc that you want to
continue listening to, press the
SCAN button again.
When activated, Disc Repeat plays
the current CD continuously. To
activate Disc Repeat, press and hold
the RPT button until you see D-RPT
in the display. To turn of f Disc
Repeat, press the RPT button again,
or press either side of the SKIP bar.
When activated, Track Repeat plays
the current track continuously. To
activate Track Repeat, press and
release the RPT button. You will see
RPT in the display as a reminder. To
turn of f Track Repeat, press the RPT
button again, or press either side of
the SKIP bar. Disc Scan Disc Repeat
T rack Repeat
Audio System
Comf ort and Convenience Feat ures140

To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJEC’’ in the display. When
you remove the disc f rom the slot,
the system automatically begins the
Load sequence so you can load
another CD in that position. If you do
not load another CD, af ter 15
seconds, the system selects the
previous mode (AM, FM1, or FM2).
If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 15 seconds, and select the
previous mode (AM or FM). To
begin playing the disc, press the CD
button.
To remove a different CD from the
changer,firstselectitwiththe
appropriate preset button. When that
CD begins playing, press the eject
button.
CONT INUED
Removing CDs f rom t he Changer
Audio System
Comf ort and Convenience Feat ures141
CD
BUTTONPWR/VOL KNOB EJECT BUTTON
CD SLOT
AM/FM BUTTON

ÛIf you turn the system of f while a
tape is playing, either with the PWR/
VOL knob or by turning of f the
ignition, the cassette will remain in
the drive. When you turn the system
back on, the cassette player will be in
pause mode. To begin playing, press
the Preset 3 (PLAY/PROG) button.
The tape direction indicator will light
to show you which side of the
cassette is playing. The indicates
thesideyouinsertedfacingupward
is now playing. If you want to play
the other side, press the Preset 3
button.
Dolby noise reduction turns on when
you insert a cassette. The indi-
cator will light in the display. If the
tape was not recorded with Dolby
noise reduction, turn it of f by
pressing the Preset 4 button.
Noise reduction remains of f until you
turn it on by pressing the button
again.
When the system reaches the end of
the tape, it will automatically reverse
direction and play the other side. If
you want to remove the cassette
from the drive, press the eject button
on the cassette player.To switch to the radio or CD
changer while a tape is playing, press
the AM/FM or CD/AUX button. To
change back to the cassette player,
push the CD/AUX button.
Audio System
Comf ort and Convenience Feat ures145

µµ
µ
You can store the
f requencies of your f avorite radio
stations in the six preset icons. Each
icon will store one f requency on the
AM band, and two f requencies on
the FM band.
To store a f requency: Repeat steps 2 to 4 to store a total
of six stations on AM and twelve
on FM.
Once a station’s f requency is stored,
simply touch the proper preset icon
to tune to it.
The preset f requencies will be lost if
your car’s battery goes dead, is
disconnected, or the radio f use is
removed. If you are
traveling far from home and can no
longer receive the stations you
preset, you can use the Auto Select
feature to find stations in the local
area.
To activate Auto Select, touch the
Auto Select icon on the display. The
A.SEL indicator will f lash in the
upper display, and the system will go
into scan mode f or several seconds.
It automatically scans both bands,
looking f or stations with strong
signals. It stores the f requencies of
six AM stations and twelve FM
stations in the preset icons. You can
then use the preset icons to select
those stations.
Pick the preset icon (1 6) you
want for that station. Touch the
icon, and hold it until you hear two
beeps. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station. Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
icon. Push the AUDIO DISPLAY button
to view the audio display. You will
see the six preset icons.
1.
2.
3.
4. 5.
Preset A UT O SEL ECT
Audio System
Comf ort and Convenience Feat ures150

To remove the disc that is currently
playing, press the eject button. You
will see ‘‘EJEC’’ in the upper display.
When you remove the disc f rom the
slot, the system automatically begins
the load sequence so you can load
another CD in that position. If you do
not load another CD, within 15
seconds, the system selects the
previous mode (AM, FM1, or FM2).
If you do not remove the disc f rom
the slot, the system will reload the
disc af ter 15 seconds and put the CD
changer in pause mode. To begin
playing the disc, press the CD button.
To remove a different CD from the
changer,firstselectitwiththe
appropriate disc icon or the DISC bar.
When that CD begins playing, press
the eject button.
Removing CDs f rom t he Changer
Audio System
Comf ort and Convenience Feat ures162
CD SLOTEJECT BUTTON
CD BUTTON CH DISC BAR