ignition Acura TSX 2007 Owner's Guide

µ To switch from low
beams to high beams, push the left
lever forward until you hear a click.
The high beam indicator will come
on (see page ). Pull it back to
return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beams will stay on as long as you
hold the lever back.
Turn the fog lights on and off by
turning the switch next to the
headlight switch.
You can use the fog lights only when
the headlights are on low beam.
They will go off when you turn the
headlights off or onto high beam. This
feature turns off the headlights,
parking lights, taillights, and license
plate lights within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
You can change this 15 second timer
to 0, 30, or 60 seconds (see page ). With the headlight switch in the off
or position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes. The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights-on
reminder chime.
66
108
Automatic Lighting Of f Feature
High Beams
Fog Lights (Canadian Models) Daytime Running L ights
Headlights, Automatic Lighting Of f Feature, Daytime Running Lights
122

Make sure the rear window is clear
and you have good visibility bef ore
starting to drive.
The rear window def ogger will clear
fog, frost, and thin ice from the
window. Push the def ogger button to
turn it on and of f . The indicator
above the button comes on to show
the def ogger is on. If you do not turn
it of f , the def ogger will shut itself of f
af ter about 35 minutes. It also shuts
of f when you turn of f the ignition
switch. You have to turn the
def ogger on again when you restart
the vehicle.
Push the button between the center
vents to turn on the hazard warning
lights (f our-way f lashers). This
causes all f our outside turn signal
lights and both turn signal indicators
in the instrument panel to flash. Use
the hazard warning lights if you need
to park in a dangerous area near
heavy traffic, or if your vehicle is
disabled.
The def ogger and antenna wires on
the inside of the rear window can be
accidentally damaged. When
cleaning the glass, always wipe side-
to-side.
Hazard Warning
Rear Window Def ogger
Hazard Warning, Rear Window Def ogger
124
Without navigation system With navigation system

These keys contain electronic
circuits that are activated by the
immobilizer system. They will not
work to start the engine if the
circuits are damaged.
Protect the keys from direct
sunlight, high temperature, and
high humidity. Donotdropthekeysorsetheavy
objects
on them.
Keep the keys away from liquids.
If they get wet, dry them
immediately with a soft cloth.
Youshouldhavereceivedakey
number
tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks.
The keys do not contain batteries.
Do not try to take them apart.
Your vehicle also comes with two
remote transmitters; see page f or an explanation of how to
operation.
The master key fits all the locks on
your vehicle. The valet key works
only in the ignition and the door
locks. You can keep the trunk
release lever, rear seat trunk access,
and glove box locked when you leave
your vehicle and the valet key at a
parking f acility. 131
Remote Transmitter
Keys and Locks
126
KEY
NUMBER
TAG
MASTER
KEY
(Black)VALET KEY
(Light Gray)

If the system repeatedly does not
recognize the coding of your key,
contact your dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undrivable.
If you lose your key and you cannot
start the engine, contact your dealer.
The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on f or
a f ew seconds, then go of f . If the
indicator starts to blink, it means the
system does not recognize the
coding of the key. Turn the ignition
switch to the LOCK (0) position,
remove the key, reinsert it, and turn
the ignition switch to the ON (II)
position again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Immobilizer System
Inst rument s and Cont rols
127

µµ
µ
µ
The ignition switch has four
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III).
You can insert or
remove the key only in this position.
To turn the key, you must push the
key in slightly. If your vehicle has an
automatic transmission, the shift
lever must also be in Park. If
the front wheels are turned, the
anti -theft lock may make it diffi cult
to turn the key. Firmly turn the
steering wheel to the left or right as
you turn the key.
You can
operate the audio system and the
accessory power sockets in this
position.
Use this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
This
is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch from the
ACCESSORY (I) to the ON (II)
position.
You will hear a reminder beeper if
you leave the key in the ignition switch
in the LOCK (0) or the
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
You will also see a ‘‘REMOVE KEY’’
message on the multi-inf ormation
display (see page ).
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch. 79
LOCK (0) A CCESSORY (I)
ST A RT (III) ON (II)
Ignition Switch
128
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.

Each front door has a master door
lock switch. Either switch locks and
unlocks all doors. On the driver’s
door, push the top of the master
door lock switch to lock all doors.
Push the bottom to unlock them.
Each
door has a lock tab on the top.
Push the tab down to lock the door
and pull it up to unlock. All
doors can be locked from the
outsidebyusingthekeyinthe
driver’s door. To unlock only the
driver’s door or all doors (depending
on the ‘‘DOOR LOCK MODE’’
setting), insert the key, turn the key,
and release it. The remaining doors
unlock when you turn the key a
second time within a few seconds.
To change this setting, see page .
Youcanopenorclosethewindows
by using the key in the driver’s door
(see page ).
To lock the passenger’s door when
getting out of the vehicle, push the
lock tab down and close the door. To
lock the driver’s door, remove the
key f rom the ignition switch and
push the lock tab down or push the
top of the master switch, then close
the door. 149
111
CONT INUED
Power Door L ocks
Door L ocks
Inst rument s and Cont rols
129
LOCK TAB
MASTER DOOR LOCK SWITCH
Unlock
Lock
DRIVER’S DOOR

On the f ront passenger’s door, push
the master door lock switch down to
lock the all doors, and up to unlock
them.The childproof door locks are
designed to prevent children seated
in the rear f rom accidentally opening
the rear doors. Each rear door has a
lock lever near the edge. With the
lever in the LOCK position, the door
cannot be opened f rom inside
regardless of the position of the lock
tab. To open the door, pull the lock
tab up, and use the outside door
handle.
With the driver’s door open and the
key in the ignition, both master door
lock switches are disabled. If you try
to lock an open driver’s door by
pushing in the lock tab, all doors will
unlock when you close the driver’s
door.
L ockout Prevent ionChildproof Door L ocks
Door L ocks, Childproof Door L ocks
130
MASTER DOOR LOCK SWITCH
Unlock
Lock Unlock
Lock
FRONT PASSENGER’S DOOR

µ
µ Pressthisbuttononce
to unlock the driver’s door or all the
doors (depending on the ‘‘DOOR
LOCK MODE’’ setting). Press it
twice to unlock the other doors.
Some exterior lights will flash twice
each time you press the button.
The ceiling light (if the ceiling light
switch is in the Door Activated
position) will come on when you
press the UNLOCK button. If you do
not open any doors within 30
seconds (or whatever setting the
‘‘INTERIOR LIGHT DIMMING
TIME’’issetto),thelightfadesout.
If you relock the doors with the
remote transmitter before 30
seconds have elapsed, the light will
go off immediatel y.
To change the ‘‘DOOR LOCK
MODE’’ setting, see page .
When
the key is in the ignition
switch, the functions of each button
are disabled.
Press this button once to
lock all doors. Some exterior lights
will flash. When you push LOCK
twice within 5 seconds, you will hear
a horn (depending on the ‘‘KEYLESS
LOCK ACKNOWLEDGEMENT’’
setting) to verify that the doors are
locked and the security system has
set. The Lock button will not work this
way if any door is not fully
closed.
You can open and close all power
windows from outside the vehicle
with the key. With the remote
transmitter, you can open the
windows. Refer to Power Windows
on page .
To
change the ‘‘KEYLESS LOCK
ACKNOWLEDGEMENT’’ setting,
see page .
149113
111
CONT INUED
UNL OCK
LOCK
Remote Transmitter
Inst rument s and Cont rols
131
PANIC
BUTTON TRUNK
RELEASE
BUTTON LOCK
BUTTON
UNLOCK
BUTTON

µµ
To
change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, refer to ‘‘SECURITY
RELOCK TIMER’’ on page .
Each remote transmitter also
activates the Driving Position
Memory System and changes the
‘‘MEMORY POSITION LINK’’
setting according to that remote (see
page ).
Pressthisbuttonfor
about 1 second to attract attention;
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the key
is in the ignition switch.
142
106
115 Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
132
DRIVER 1 REMOTE DRIVER 2 REMOTE

In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
Follow these precautions whenever
you use the seat heaters:If the engine is lef t idling f or an
extended period, do not use the
seat heaters even on the LO
setting. It can weaken the battery,
causing hard starting. Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
Both f ront seats are equipped with
seat heaters. The passenger seat is
only heated in the seat bottom
because of the side airbag of f system. The ignition switch must be in the
ON (II) position to use them. Push
the front of the switch, HI, to rapidly
heat up the seat. After the seat
reaches a comf ortable temperature,
select LO by pushing the back of the
switch. This will keep the seat warm.
Seat Heaters
Inst rument s and Cont rols
137
SEAT HEATER SWITCHES
Passenger’s
Seat
Driver’s
Seat
HEATERS