clock Acura TSX 2007 Owner's Manual

While the multi-information display
is showing ‘‘DOOR · WINDOW
SETUP,’’ press the SEL/RESET
buttononthesteeringwheel.The
display changes to ‘‘DOOR LOCK
MODE’’ as shown above.Press the SEL/RESET button. The
display changes as shown above.
In def ault setting, if you push the
UNLOCK button once on the remote
transmitter or turn the key clockwise
in the driver’s door lock, only the
driver’s door unlocks.
You can select whether only the
driver’s door unlocks or all the doors
unlock in ‘‘DOOR LOCK MODE.’’
Select ‘‘DRIVER DOOR’’ or ‘‘ALL
DOORS’’ by pressing the INFO
button, and enter your selection by
pressing the SEL/RESET button.
CONT INUED
Door L ock Mode
Multi-Inf ormation Display
Inst rument s and Cont rols
111

The back of the rear seat folds down
to give you direct access to the trunk.
Each side f olds down separately.
With only half the seat f olded, you
can still carry a passenger in the
back seat. The seat-back can be
released f rom inside the vehicle or
inside the trunk.To f old down either side of the seat-
back f rom inside the vehicle, insert
the master key in the lock on the
rear shelf . To f old down the driver’s
side, turn the key clockwise, pull
down the top of the seat-back, then
release the key. To f old down the
passenger’s side, turn the key
counterclockwise and perf orm the
same procedure.
To remove a head restraint f or
cleaning or repair, pull it up as f ar as
it will go. Push the release button
and pull the restraint out of the seat-
back.
Seats
Folding Rear Seat
140
MASTER KEY
REAR OUTSIDE POSITION
RELEASE BUTTON

To open: You can open and close the windows
with the key in the driver’s door lock.Insert the key in the driver’s door
lock.
Turn the key clockwise, then
release it.
You can open all of the windows
from the outside with the remote
transmitter.
Press the UNLOCK button once
to unlock the driver’s door
(depending on the ‘‘DOOR LOCK
MODE’’ setting).
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
f our windows start to open. To
stop the windows, release the
button.
To open the windows further,
press the button again (within 10
seconds).
You cannot close the windows with
the remote transmitter. Turnthekeyclockwiseagain,and
hold it. All f our windows start to
open. To stop the windows,
release the key.
To open the windows f urther, turn
andholdthekeyagain(within
10 seconds).
To close: Insert the key in the driver’s door
lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again, and hold it. All four
windowsstarttoclose.Tostopthe
windows, release the key.
To close the windows f urther, turn
andholdthekeyagain(within
10 seconds).
1.
2.
3.
1.
2.1.
2.
3. 3.
4.
4.
Power Windows
Opening t he Windows wit h t he
Remote Transmitter
Opening/Closing t he Windows wit hthe Key
Inst rument s and Cont rols
149
Open
Close UNLOCK BUTTON

...............
Climate Control System . 160
................
Automatic Operation . 162
.......
Semi-automatic Operation . 163
..........
Dual Temperature Control . 167
..............
Climate Control Sensors . 169
..........
Playing the AM/FM Radio . 170
.....................
Adjusting the Sound .175
............
AM/FM Radio Reception . 177
Playing the XM
Satellite
..........................................
Radio .179
......................
Auxiliary Input Jack .184
.................................
Playing Discs .185
.....
CD Changer Error Messages . 193
.....................
Protecting your CDs .194
...............................
Playing a Tape .195
.............
Steering Wheel Controls . 200
.................
Radio Thef t Protection . 201
..........................
Setting the Clock .202
............................
Security System .203
...............................
Cruise Control .204
HomeLink Universal ................................
Transceiver .207
..........................
HandsFreeLink .211
The climate control system in your
vehicle provides a comfortable
driving environment in all weather
conditions.
The standard audio system has
many f eatures. This section
describes those f eatures and how to
use them.
Your vehicle has an anti-theft audio
system that requires a code number
to enable it.
The security system helps to dis-
courage vandalism and thef t of your
vehicle.
Features
Features
159
TM

For example:1:06 would RESET to 1:00.
1:52 would RESET to 2:00.
Refer to the navigation system
owner’s manual to set up the time.
If your vehicle’s battery is
disconnected or goes dead, you may
need to set the clock.
To set or change the time, press and
hold the TUNE/SOUND knob until
you hear a beep. The displayed time
begins to blink. Press on the H
(Preset 4) until the numbers advance
to the desired time. Change the
minutes by pressing the M (Preset
5) until the numbers advance to the
desired time. When you are f inished,
press the TUNE/SOUND knob
again to set the time.
You can quickly set the time to the
nearest hour. If the time displayed is
bef ore the half hour, press and hold
the TUNE/SOUND knob, then press
theR(Preset6)tosetthetimeback
to the previous hour.
If the time displayed is af ter the half
hour, the same procedure sets the
time f orward to the beginning of the
next hour.
On vehicles without navigation system
On vehicles with navigation system
Setting the Clock
202
TUNE/SOUND
KNOBR BUTTON
M BUTTON
DIGITAL CLOCK
H BUTTON

Make sure the engine and radiator
are cool.
Remove the radiator cap by
pushing down and turning
counterclockwise. Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.
Put the radiator cap back on, and
tighten it fully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components. Check the f luid level in the
windshield washer reservoir at least
monthly during normal use.
Check the reservoir’s f luid level by
removing the cap and looking at the
level gauge attached to the cap.
4.
1.
2.
3. 5.
6.
Engine Coolant, Windshield Washers
Windshield Washers
292
RADIATOR CAP
LEVEL GAUGE

Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to test the new
bulb.
Insert the socket back into the
headlight assembly. Make sure
the bulb is installed correctly by
looking through the headlight lens.
Pivot the hold-down wire back in
place, and clip the end into the slot.
Install the rubber weather seal
over the back of the headlight
assembly.Makesureitisright
side up; it is marked with an arrow.
Push the electrical connector onto
the socket. Make sure it is
connected securely.
Turn on the headlights to test the
new bulb.
On the driver’s side, reinstall the
air intake cover. Reinstall the
three fasteners and secure them
by pushing on the heads until they
lock. 3.
4.
5.
2. 1.
9. 8.
10. 7. 6.
Replacing the Turn Signal L ight
Bulb
Lights
300
BULB
SOCKET

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
4. 5.
2.
1.
3.
CONT INUED
Replacing a Front Side Marker/
FrontParkingLightBulb
Lights
Maint enance
301
HOLDING CLIPS

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to test the new
bulb.
Put the inner f ender cover in place.
Install and lock each holding clip
bypushingonthecenter.Open the trunk.
Remove the light assembly cover
by pulling its outside edge.
Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket.Push a new bulb straight into the
socket until it bottoms, and
reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Test the new bulb to make sure it
works.
Reinstall the light assembly cover.
1.
3. 2.
6.
7.
8.
4.
5.
6.
Replacing Rear Bulbs
(In Fenders)
Lights
302
COVER

Open the trunk.
Pull the lining back caref ully.Determine which of the two bulbs
is burned out: taillight or back-up
light.
To replace a bulb on the right side,
remove the trim clip. For the lef t
side, remove the two trim clips. Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to test the new
bulb.
Reinstall the trunk lid trim. Make
sure it is installed under the edge
of the trunk lid seal.
Press the trim clips back into their
holes.
1.
2. 5.
6. 4.
3. 7.
8.
9.
10.
Replacing Rear Bulbs
(in T runk L id)
Lights
Maint enance
303
SOCKETS BULBS
TRIM CLIPS