ECO mode Acura TSX 2008 User Guide

If you f ail to enter the desired
adjustment properly, you will see the
above display for several seconds,
then the display goes back to
‘‘CUSTOMIZE MENU.’’ Repeat the
adjustment.To exit ‘‘ADJUST OUTSIDE TEMP.
DISPLAY,’’ press the INFO button
until you see ‘‘EXIT,’’ and press the
SEL/RESET button. The display
goes back to ‘‘CUSTOMIZE MENU.’’
When your selection is successf ully
entered, you will see the above
display f or several seconds, and then
the display goes back to
‘‘CUSTOMIZE MENU.’’
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
97
U.S. model is shown
\f—\f—
y
y
(\fy\f
\fy
2008 TSX

When your selection is successf ully
entered, you will see the above
display f or several seconds, and then
the display goes back to
‘‘CUSTOMIZE MENU.’’If you f ail to enter your selection,
you will see the above display f or
several seconds, then the display
goes back to ‘‘CUSTOMIZE MENU.’’
Repeat the setup.To exit ‘‘DOOR LOCK MODE,’’
press the INFO button until you see
‘‘EXIT,’’ then press the SEL/RESET
button. The display goes back to
‘‘CUSTOMIZE MENU.’’
Multi-Inf ormation Display
112
\f—\f—
y
\f
y
(\fy\f

y
2008 TSX

µTo switch f rom low
beams to high beams, push the lef t
lever f orward until you hear a click.
The high beam indicator will come
on (see page ). Pull it back to
return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beams will stay on as long as you
hold the lever back.
Turn the f og lights on and of f by
turning the switch next to the
headlight switch.
You can use the f og lights only when
the headlights are on low beam.
They will go of f when you turn the
headlights of f or onto high beam. This f eature turns of f the headlights,
parking lights, taillights, and license
plate lights within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
You can change this 15 second timer
to 0, 30, or 60 seconds (see page
). With the headlight switch in the off
or position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes. The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights on
reminder chime.
66
108
Automatic Lighting Of f Feature
High Beams
Fog Lights (Canadian Models)
Daytime Running L ights
Headlights, Automatic Lighting Of f Feature, Daytime Running Lights
122
\f—\f—
y
\f\fy
(\fy\f
y
2008 TSX

The headlights revert to normal
operation when you turn them on
with the switch.The level of brightness is shown on
the multi-information display while
you adjust it. It goes out 5 seconds
af ter you f inish adjusting.
When the multi-information display
shows a ‘‘DRL OFF’’ message, the
daytime running lights are of f .
Follow the procedure in the previous
page to turn them on.
To reduce glare at night, the instru-
ment panel illumination dims when
you turn the light switch to or. Turning the select/reset knob
f ully to the right until you hear a
click will cancel the reduced bright-
ness.
If you see a ‘‘CHECK DRL
SYSTEM’’ message on the multi-
inf ormation display, there is a
problem in the high beam headlight’s
circuit. Take your vehicle to a dealer
to have it checked.
The select/reset knob on the
instrument panel controls the
brightness of the instrument panel
lights. Turn the knob to adjust the
brightness.
Instrument Panel Brightness
Daytime Running L ights, Instrument Panel Brightness
Inst rument s and Cont rols
123
SELECT/RESET KNOB BRIGHTNESS LEVEL
U.S. model is shown
\f—\f—
y
\f
y
(\fy\f
y
2008 TSX

Each f ront door has a master door
lock switch. Either switch locks and
unlocks all doors. On the driver’s
door, push the top of the master
door lock switch to lock all doors.
Push the bottom to unlock them.
Each door has a lock tab on the top.
Push the tab down to lock the door
and pull it up to unlock. All doors can be locked f rom the
outsidebyusingthekeyinthe
driver’s door. To unlock only the
driver’s door or all doors (depending
on the ‘‘DOOR LOCK MODE’’
setting), insert the key, turn the key,
and release it. The remaining doors
unlock when you turn the key a
second time within a f ew seconds.
To change this setting, see page .
Youcanopenorclosethewindows
by using the key in the driver’s door
(see page ).
To lock the passenger’s door when
getting out of the vehicle, push the
lock tab down and close the door. To
lock the driver’s door, remove the
key f rom the ignition switch and
push the lock tab down or push the
top of the master switch, then close
the door. 149
111
CONT INUED
Power Door L ocks
Door L ocks
Inst rument s and Cont rols
129
LOCK TAB
MASTER DOOR LOCK SWITCH
Unlock
Lock
DRIVER’S DOOR
\f—\f—
y
\f
y
(\fy\f
y
2008 TSX

µ
µ Pressthisbuttononce
to unlock the driver’s door or all the
doors (depending on the ‘‘DOOR
LOCK MODE’’ setting). Press it
twice to unlock the other doors.
Some exterior lights will f lash twice
each time you press the button.
The ceiling light (if the ceiling light
switch is in the Door Activated
position) will come on when you
press the UNLOCK button. If you do
not open any doors within 30
seconds (or whatever setting the
‘‘INTERIOR LIGHT DIMMING
TIME’’issetto),thelightfadesout.
If you relock the doors with the
remote transmitter before 30
seconds have elapsed, the light will
go of f immediately.
To change the ‘‘DOOR LOCK
MODE’’ setting, see page .
When the key is in the ignition
switch, the f unctions of each button
are disabled.
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds, you will hear
a horn (depending on the ‘‘KEYLESS
LOCK ACKNOWLEDGEMENT’’
setting) to verify that the doors are
locked and the security system has
set. The Lock button will not work this way if any door is not f ully
closed.
You can open and close all power
windows from outside the vehicle
with the key. With the remote
transmitter, you can open the
windows. Refer to Power Windows
on page .
To change the ‘‘KEYLESS LOCK
ACKNOWLEDGEMENT’’ setting,
see page .
149113
111
CONT INUED
UNL OCK
LOCK
Remote Transmitter
Inst rument s and Cont rols
131
PANIC
BUTTON
TRUNK
RELEASE
BUTTON
LOCK
BUTTON
UNLOCK
BUTTON
\f—\f—
y
\fy
(\fy\f
y
2008 TSX

µµ
To change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, refer to ‘‘SECURITY
RELOCK TIMER’’ on page .
Each remote transmitter also
activates the Driving Position
Memory System and changes the
‘‘MEMORY POSITION LINK’’
setting according to that remote (see
page ).
Pressthisbuttonfor
about 1 second to attract attention;
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the key
is in the ignition switch. Standing outside the vehicle with
all the doors shut, push the lock
and unlock buttons at the same
time until the LED on the remote
transmitter blinks 2 times.
Open and shut the driver’s door.
Use the remote transmitter to lock
and unlock the driver’s door.
Verify that the remote transmitter
is in the linked mode. Turn the
ignition switch to the ON (II)
position. The MID display should
read ‘‘Welcome Driver 1’’ or
‘‘Welcome Driver 2’’, depending on
which remote you just linked (the
remote number is on the back of
the remote transmitter).
If theMIDdisplayonlyreads
‘‘Welcome Driver’’ once the ignition
switch is turned to the ON (II)
position, the link f rom the remote
transmitter to the vehicle has failed.
Repeat the procedure. If the link still
f ails, see your dealer.
106
115 1.
2.
3.
4.
143
Recalling a Memorized Driving
Position
PA NIC
TRUNK L inking Your Remote
Transmitter
Remote Transmitter
132
DRIVER 1 REMOTE DRIVER 2 REMOTE
——
y
y
(y
y
2008 TSX

To open:
You can open and close the windows
with the key in the driver’s door lock.Insert the key in the driver’s door
lock.
Turn the key clockwise, then
release it.
You can open all of the windows
from the outside with the remote
transmitter.
Press the UNLOCK button once
to unlock the driver’s door
(depending on the ‘‘DOOR LOCK
MODE’’ setting).
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
f our windows start to open. To
stop the windows, release the
button.
To open the windows further,
press the button again (within 10
seconds).
You cannot close the windows with
the remote transmitter. Turnthekeyclockwiseagain,and
hold it. All f our windows start to
open. To stop the windows,
release the key.
To open the windows f urther, turn
andholdthekeyagain(within
10 seconds).
To close: Insert the key in the driver’s door
lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again, and hold it. All four
windowsstarttoclose.Tostopthe
windows, release the key.
To close the windows f urther, turn
andholdthekeyagain(within
10 seconds).
1.
2.
3.
1.
2.1.
2.
3.
3.
4.
4.
Power Windows
Opening t he Windows wit h t he
Remote Transmitter
Opening/Closing t he Windows wit hthe Key
Inst rument s and Cont rols
149
Open
Close UNLOCK BUTTON
\f—\f—
y
\f\fy
(\fy\f
y
2008 TSX

µ
µ
µ
CONT INUED
The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM.
Pick the preset number (1 6)
you want for that station. Press
the button or icon and hold it until
you hear a beep.
Each preset button or icon
can store one f requency on AM, and
two f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button or icon.
To use the SCAN, preset and A.SEL
function, press the AUDIO button to
view these icons.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button, or
touch the SCAN icon (models with
navigation system), then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor5seconds.Whenit
plays a station you want to listen to,
press the SCAN button or touch the
SCAN icon again. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
3.
4.
1.
2.
On vehicles with navigation system
Playing the AM/FM Radio
Preset
SCAN
Features
173
\f—\f—
y


y
(\fy\f
y
2008 TSX

µ
µ If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area. If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons or icons. Use the TUNE,
SEEK, or SCAN f unction to f ind
stations, then store them in the
preset buttons or icons as described
previously.
Press the A. SEL button or touch the
A. SEL icon. A. SEL will appear in
the display, and the system will go
into scan mode f or several seconds.
It stores the f requencies of six AM,
and twelve FM stations in the preset
buttons (1 6) or icons. You will
see a ‘‘0’’ displayed af ter pressing a
preset button or icon if Auto Select
cannot f ind a strong station f or every
preset button or icon. press the
A.SEL button or touch the A.SEL
icon. This restores the presets you
originally set.
To turn of f Auto Select,
AUTO SELECT
Playing the AM/FM Radio
174
\f—\f—
y

\fy
(\fy\f
y
2008 TSX