steering wheel Acura TSX 2008 Service Manual

Your vehicle is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The anti-lock
brake system (ABS) helps you retain
steering control when braking very
hard.The hydraulic system that operates
the brakes has two separate circuits.
Each circuit works diagonally across
the vehicle (the lef t-f ront brake is
connected with the right-rear brake,
etc.). If one circuit should develop a
problem, you will still have braking
at two wheels.All f our brakes have audible brake
wear indicators.
If the brake pads need replacing, you
will hear a distinctive, metallic
screeching sound when you apply
the brake pedal. If you do not have
the brake pads replaced, they will
screech all the time. It is normal f or
the brakes to occasionally squeal or
squeak when you apply them.
Resting your f oot on the pedal keeps
the brakes applied lightly, builds up
heat, increases wear, and reduces
their ef f ectiveness. It also keeps
your brake lights on all the time,
conf using drivers behind you.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by taking your f oot of f the
accelerator and downshif ting to a
lower gear. Check the brakes after driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Be extra
cautious and alert in your driving.
Braking System
Braking System Design
Brake Pad Wear Indicators
260
\f—\f—
y
y
(\fy\fy
2008 TSX

CONT INUED
If this indicator comes on, the anti-
lock f unction of the braking system
has shut down. The brakes still work
like a conventional system, but
without anti-lock. You should have
your dealer inspect your vehicle as
soon as possible.
If the ABS indicator and the brake
system indicator come on together,
and the parking brake is f ully
released, the EBD system may also
be shut down.
The anti-lock brake system (ABS)
helpspreventthewheelsfrom
locking up, and helps you retain
steering control by pumping the
brakes rapidly, much f aster than a
person can do it.
The electronic brake distribution
(EBD) system, which is part of the
ABS, also balances the f ront-to-rear
braking distribution according to
vehicle loading.
You will f eel a pulsation in the brake
pedal when the ABS activates, and
you may hear some noise. This is
normal: it is the ABS rapidly
pumpingthebrakes.Ondry
pavement, you will need to press on
thebrakepedalveryhardbeforethe
ABS activates. However, you may
feel the ABS activate immediately if
you are trying to stop on snow or ice.
Let the ABS work f or you by always
keeping f irm, steady pressure on the
brake pedal. This is sometimes
ref erred to as ‘‘stomp and steer.’’ When the ABS indicator comes on,
you will also see a ‘‘CHECK ABS
SYSTEM’’ message on the multi-
inf ormation display.
You should never pump the brake pedal.
Anti-lock Brakes (ABS)
ABS Indicator
Driving
261
\f—\f—
y
y
(\fy\fy
2008 TSX

It only helps with the
steering control during braking.
such as trying to take a
corner too f ast or making a sudden
lane change. Always drive at a safe
speed f or the road and weather
conditions.
Always steer moderately
when you are braking hard. Severe
or sharp steering wheel movement
can still cause your vehicle to veer
into oncoming traffic or off the road.
Test your brakes as instructed on
page . If the brakes f eel normal,
drive slowly and have your vehicle
repaired by your dealer as soon as
possible. Avoid sudden hard braking
which could cause the rear wheels to
lock up and possibly lead to a loss of
control.
The VSA indicator will come on
alongwiththeABSindicator.
on loose or
uneven surfaces, such as gravel or
snow, than a vehicle without anti-
lock.
338
Anti-lock Brakes (ABS)
Import ant Saf et y Reminders
A BS does not reduce the time or
distance it takes to stop the
vehicle.
A BS will not prevent a skid that
results f rom changing direction
abruptly,
A BS cannot prevent a loss of
stability. A vehicle with A BS may require a
longer distance to stop
262
\f—\f—
y
\fy
(\fy\fy
2008 TSX

When preparing to tow, and bef ore
driving away, be sure to check the
f ollowing:Always drive slowly and have
someone guide you when backing up.
Grip the of the steering
wheel; then turn the wheel to the lef t
to get the trailer to move to the left,
andturnthewheelrighttomovethe
trailer to the right.
Follow all normal precautions when
parking, including f irmly setting the
parking brake and putting the
transmission in Park (automatic) or
in f irst or reverse (manual). Also,
place wheel chocks at each of the
trailer’s tires.
The vehicle has been properly
serviced, and the suspension,
cooling system, and lights are in
good operating condition.
Crosswinds and air turbulence
caused by passing trucks can disrupt
your steering and cause the trailer to
sway. When being passed by a large
vehicle, keep a constant speed, and
steer straight ahead. Do not try to
make quick steering or braking
corrections.Your vehicle tires and spare are
properly inf lated (see page ),
and the trailer tires and spare are
inflated as recommended by the
trailer maker.
The lights and brakes on your
vehicle and the trailer are working
properly.
All items in or on the trailer are
properly secured and cannot shif t
while you drive.
Thehitch,safetychains,andany
other attachments are secure.
All weights and loads are within
limits (see pages and ).
The trailer has been properly
serviced and is in good condition. 270 315
271
bottom
Pre-T ow ChecklistBacking Up
Parking
Handling Crosswinds and Buf f et ing
Towing a Trailer
274
\f—\f—
y
\f

y
(\fy\fy
2008 TSX

This section explains why it is
important to keep your vehicle well
maintained and how to f ollow basic
maintenance saf ety precautions.
This section also includes
instructions on how to read the
maintenance messages on the multi-
inf ormation display and instructions
for simple maintenance tasks you
may want to take care of yourself.
If you have the skills and tools to
perf orm more complex maintenance
tasks on your vehicle, you may want
to purchase the service manual. See
page f or inf ormation on how to
obtain a copy, or see your dealer.......................
Maintenance Saf ety .278
....................
Maintenance Minder .280
..............................
Fluid Locations .290
........................
Adding Engine Oil .291
Changing the Engine Oil and ...........................................
Filter .293
..............................
Engine Coolant .295
....................
Windshield Washers .296
.......................
Transmission Fluid .297
..........
Automatic Transmission .297
..............
Manual Transmission .299
................
Brake and Clutch Fluid .300
....................
Power Steering Fluid .301
.............................................
Lights .302
.......................................
Seat Belts .310
.....................................
Floor Mats .310
..................
DustandPollenFilter .311
.................................
Wiper Blades .312
...........................................
Wheels .314
...............................................
Tires .314
...................
Checking the Battery .320
.............................
Vehicle Storage .321
369
Maintenance
Maint enance
277
\f—\f—
y
\fy
(\fy\fy
2008 TSX

µ
µ
µ
µ
µ
µ
µ
µ
µ
µµ
µ
To see the current engine oil lif e
displayed on the lower segment of
the multi-information display, turn
the ignition switch to the ON (II)
position, and press the SEL/RESET
buttononthesteeringwheel
repeatedly until engine oil lif e is
displayed. The remaining engine oil lif e is
shownonthedisplayaccordingto
this table:
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%)
100% 90%
80%
70%
60%
50%
40%
30%
20%
15%
10% 5%
0%
Your vehicle displays engine oil lif e
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perf orm engine oil
replacement and indicated
maintenance service.
Based on the engine operating
conditions and accumulated engine
revolutions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e and displays it as a
percentage.
Maintenance Minder
Engine Oil L if e Display
280
ENGINE OIL LIFE DISPLAY
REMAINING ENGINE OIL LIFE
\f—\f—
y
\fy
(\fy\fy
2008 TSX

CONT INUED
When the remaining engine oil lif e is
15 to 6 %, the multi-inf ormation
display shows a ‘‘SERVICE DUE
SOON’’ message along with the
maintenance item code(s) indicating
themainandsubitemsrequiredat
thetimeof theoilchange.Referto
page f or a complete list of the
maintenance main items and sub
items.When the message appears, the
system message indicator also
comes on (see page ). Even after
you press the INFO button to cancel
the message, the indicator continues
to stay on until you have the service
perf ormed.
To cancel the message, press the
INFO button on the steering wheel.
Af ter the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see the
percentage of the remaining engine
oillifeandthemaintenanceitem
code(s) displayed.
75
289
Maintenance Minder
Maint enance
281
MAIN ITEM SUB ITEMS
MAINTENANCE ITEM CODE(S)
\f—\f—
y

\fy
(\fy\fy
2008 TSX

To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
The message appears on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position. Af ter canceling the
message, the engine oil lif e display
will appear in the lower segment.
This continues until you have the
indicated maintenance done by your
dealer.When the remaining oil lif e is 5 to 1%,
the multi-information display shows
a ‘‘SERVICE DUE NOW’’ message.
The display also shows the same
maintenance items that were
previously shown with ‘‘SERVICE
DUE SOON.’’ Make sure you have
the indicated maintenance
perf ormed as soon as possible.To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
After have the service is performed,
make sure to reset the display as
described on page .
283
Maintenance Minder
282
\f—\f—
y


y
(\fy\fy
2008 TSX

If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display. Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
modewillbeshownonthemulti-
inf ormation display.
To reset the engine oil lif e, press
the INFO button on the steering
wheel to select ‘‘RESET’’ on the
display, and press the SEL/
RESET button.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage of the remaining engine
oil lif e and the maintenance item
code(s) displayed. Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ on the lower
segment of the multi-inf ormation
display and the maintenance item
code(s) erased the next time you
turn the ignition switch to the ON
(II) position.
If the engine oil lif e display is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it comes back.
1.
2.
3.
CONT INUED
Maintenance Minder
Maint enance
283
‘‘SERVICE’’ MESSAGE
\f—\f—
y

y
(\fy\fy
2008 TSX

If you do not complete the reset
procedure within 30 seconds af ter
selecting the reset mode, the mode
will be canceled automatically.
If you have the required service
perf ormed but do not reset the
display, or reset the display without
perf orming the service, the system
will not show the proper
maintenance intervals. This can lead
to serious mechanical problems
because you will no longer have an
accurate record of when
maintenance is needed.To cancel resetting the oil life,
presstheINFObuttononthe
steering wheel to select
‘‘CANCEL’’ on the display, and
press the SEL/RESET button.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
If the indicated maintenance service
is not done and the remaining engine
oil lif e reaches 0 %, the multi-
inf ormation display will show the
message ‘‘SERVICE PAST DUE’’
and the maintenance item code(s).
This message is displayed when the
total mileage is less than 10 miles
(f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%. To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
Maintenance Minder
284
\f—\f—
y

y
(\fy\fy
2008 TSX