wheel Acura TSX 2008 Workshop Manual

CONT INUED
When the remaining engine oil lif e is
15 to 6 %, the multi-inf ormation
display shows a ‘‘SERVICE DUE
SOON’’ message along with the
maintenance item code(s) indicating
themainandsubitemsrequiredat
thetimeof theoilchange.Referto
page f or a complete list of the
maintenance main items and sub
items.When the message appears, the
system message indicator also
comes on (see page ). Even after
you press the INFO button to cancel
the message, the indicator continues
to stay on until you have the service
perf ormed.
To cancel the message, press the
INFO button on the steering wheel.
Af ter the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see the
percentage of the remaining engine
oillifeandthemaintenanceitem
code(s) displayed.
75
289
Maintenance Minder
Maint enance
281
MAIN ITEM SUB ITEMS
MAINTENANCE ITEM CODE(S)
\f—\f—
y

\fy
(\fy\fy
2008 TSX

To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
The message appears on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position. Af ter canceling the
message, the engine oil lif e display
will appear in the lower segment.
This continues until you have the
indicated maintenance done by your
dealer.When the remaining oil lif e is 5 to 1%,
the multi-information display shows
a ‘‘SERVICE DUE NOW’’ message.
The display also shows the same
maintenance items that were
previously shown with ‘‘SERVICE
DUE SOON.’’ Make sure you have
the indicated maintenance
perf ormed as soon as possible.To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
After have the service is performed,
make sure to reset the display as
described on page .
283
Maintenance Minder
282
\f—\f—
y


y
(\fy\fy
2008 TSX

If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display. Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
modewillbeshownonthemulti-
inf ormation display.
To reset the engine oil lif e, press
the INFO button on the steering
wheel to select ‘‘RESET’’ on the
display, and press the SEL/
RESET button.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage of the remaining engine
oil lif e and the maintenance item
code(s) displayed. Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ on the lower
segment of the multi-inf ormation
display and the maintenance item
code(s) erased the next time you
turn the ignition switch to the ON
(II) position.
If the engine oil lif e display is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it comes back.
1.
2.
3.
CONT INUED
Maintenance Minder
Maint enance
283
‘‘SERVICE’’ MESSAGE
\f—\f—
y

y
(\fy\fy
2008 TSX

If you do not complete the reset
procedure within 30 seconds af ter
selecting the reset mode, the mode
will be canceled automatically.
If you have the required service
perf ormed but do not reset the
display, or reset the display without
perf orming the service, the system
will not show the proper
maintenance intervals. This can lead
to serious mechanical problems
because you will no longer have an
accurate record of when
maintenance is needed.To cancel resetting the oil life,
presstheINFObuttononthe
steering wheel to select
‘‘CANCEL’’ on the display, and
press the SEL/RESET button.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
If the indicated maintenance service
is not done and the remaining engine
oil lif e reaches 0 %, the multi-
inf ormation display will show the
message ‘‘SERVICE PAST DUE’’
and the maintenance item code(s).
This message is displayed when the
total mileage is less than 10 miles
(f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%. To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
Maintenance Minder
284
\f—\f—
y

y
(\fy\fy
2008 TSX

After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
maintenance item code(s), and the
total negative mileage af ter the oil
lif e becomes 0 % is displayed.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
This message is displayed when you
drive over 10 miles (f or U.S. models)
or 10 km (f or Canadian models)
after seeing the 0 % message.
Also, the total negative mileage
keeps blinking on the display.
This particular message is displayed
when you drive over 10 miles (f or
U.S. models) or 10 km (f or Canadian
models) af ter seeing the 0 %
message.
To cancel the message, press the
INFO button on the steering wheel.
To see the message again, wait f or
an interval of more than 5 seconds,
and then press the INFO button. To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
Maintenance Minder
286
U.S.
CANADA
\f—\f—
y


y
(\fy\f
y
2008 TSX

Check the level on the side of the
reservoir when the engine is cold.
The f luid should be between the
UPPER LEVEL and LOWER LEVEL.
If not, add power steering f luid to the
UPPER LEVEL.Pour the f luid slowly and caref ully
so you do not spill any. Clean up
any spill immediately; it could
damage components in the engine
compartment.
A low f luid level can indicate a leak
in the clutch system. Have this
system inspected as soon as possible.
The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If it is not, add
brake f luid to bring it up to that level.
Use the same fluid specified for the
brake system. Always use Honda Power Steering
Fluid. You may use another power
steering f luid as an emergency
replacement, but have the power
steering system f lushed and ref illed
with Honda PSF as soon as possible.
A low power steering f luid level can
indicate a leak in the system. Check
the f luid level f requently, and have
the system inspected as soon as
possible.
Manual Transmission only
Clutch Fluid
Power Steering Fluid
Brake and Clutch Fluid, Power Steering Fluid
Maint enance
301
MAX
MIN UPPER LEVEL
LOWER LEVEL
Turning the steering wheel to f ull lef t
or right lock and holding it there can
damage the power steering pump.
\f—\f—
y
y
(\fy\f\fy
2008 TSX

To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.Use a f lat-tipped screwdriver to
remove the two holding clips f rom
the inner f ender.
Pull the inner f ender cover away
f rom the f ender and bumper.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
4. 5.
2.
1.
3.
CONT INUED
Replacing a Front Side Marker/
FrontParkingLightBulb
Lights
Maint enance
305
HOLDING CLIPS BULBSOCKET
\f—\f—
y
\fy
(\fy\f
\fy
2008 TSX

Keeping the tires properly inf lated
provides the best combination of
handling, tread lif e, and riding
comf ort.
To saf ely operate your vehicle, your
tires must be the proper type and
size, in good condition with adequate
tread, and correctly inf lated.
The f ollowing pages give more
detailed inf ormation on how to take
care of your tires and what to do
when they need to be replaced.
Clean the wheels as you would the
rest of the exterior. Wash them with
thesamesolution,andrinsethem
thoroughly.
Aluminum alloy wheels have a
protective clear-coat that keeps the
aluminum f rom corroding and
tarnishing. Cleaning the wheels with
harsh chemicals (including some
commercial wheel cleaners) or a stif f
brush can damage the clear-coat. To
clean the wheels, use a mild
detergent and a sof t brush or sponge. Underinf lated tires wear unevenly,
adversely af f ect handling and f uel
economy, and are more likely to
fail from being overheated.
Overinf lated tires can make your
vehicleridemoreharshly,are
more prone to damage f rom road
hazards, and wear unevenly.
Thetirepressuremonitoringsystem
(TPMS)willwarnyouwhenatire
pressure is low. See page f or
inf ormation on the TPMS. 263
Inf lation Guidelines
Tires
Wheels
Wheels, Tires
314
Using tires that are excessively
worn or improperly inflated can
cause a crash in which you can
be seriously hurt or killed.
Follow all instructions in this
owner’s manual regarding tire
inflation and maintenance.
\f—\f—
y

y
(\fy\f
y
2008 TSX

CONT INUED
Replace your tires with radial tires of
the same size, load range, speed
rating, and maximum cold tire
pressure rating (as shown on the
tire’s sidewall).
Mixing radial and bias-ply tires on
your vehicle can reduce braking
ability, traction, and steering
accuracy. Using tires of a dif f erent
size or construction can cause the
ABS and vehicle stability assist
system (VSA) to work inconsistently.
To help increase tire lif e and
distribute wear more evenly, rotate
the tires according to the
maintenance messages displayed on
the multi-information display. Move
the tires to the positions shown in
the illustration each time they are
rotated. If you purchase directional
tires, rotate only front-to-back.
When the tires are rotated, make
sure the air pressures are checked.
In addition to proper inf lation,
correct wheel alignment helps to
decrease tire wear. If you f ind a tire
is worn unevenly, have your dealer
check the wheel alignment.
Have your dealer check the tires if
you f eel a consistent vibration while
driving. A tire should always be
rebalanced if it is removed f rom the
wheel. When you have new tires
installed, make sure they are
balanced. This increases riding
comf ort and tire lif e. For best results,
have the installer perform a dynamic
balance.
Tires
Replacing T ires and Wheels
Tire Rotation
T ire Maintenance
Maint enance
317
Front
(For non-directional
tires and wheels) (For directional
tires and wheels)
Improper wheel weights can damage
your vehicle’s aluminum wheels. Use
only genuine Acura wheels weights f or
balancing.
\f—\f—
y
y
(\fy\fy
2008 TSX

Wheel:
Tire:
See page f or DOT tire quality
grading inf ormation, and pagef or tire size inf ormation.
If you ever replace a wheel, make
sure that the wheel’s specif ications
match those of the original wheels.
Replacement wheels are available at
your dealer.
The ABS and VSA system work by
comparing the speed of each wheel.
When replacing tires, use the same
size originally supplied with the
vehicle. Tire size and construction
can af f ect wheel speed and may
cause the system to activate.
It is best to replace all f our tires at
thesametime.If thatisnotpossible
or necessary, replace the two f ront
tires or two rear tires as a pair.
Replacing just one tire can seriously
af f ect your vehicle’s handling.
Also be sure you use only TPMS
specif ic wheels. If you do not, the
tire pressure monitoring system will
not work.
353
352
Tires
Wheel and T ire Specif ications
318
17x7J
P215/50R17 93V (TPMS)
Installing improper tires on your
vehicle can affect handling and
stability. This can cause a crash
in which you can be seriously
hurt or killed.
Always use the size and type of
tires recommended in this
owner’s manual.
——
y
y
(yy
2008 TSX