Acura TSX 2008 Manual PDF

This shows how much f uel you
have. It may show slightly more
or less than the actual amount.
The needle returns to the
bottom after you turn off the
ignition.
This shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise to
about the middle of the gauge. In
severe driving conditions, such as
very hot weather or a long period of
uphill driving, the pointer may rise to
the upper zone. If it reaches the red (Hot) mark, pull saf ely to the side of
the road. See page f or
instructions and precautions on
checking the engine’s cooling
system.
333
Gauges
Temperature Gauge Fuel Gauge
68
TACHOMETER
SPEEDOMETER
TEMPERATURE
GAUGE
INFO KNOB SELECT/RESET KNOBFUEL GAUGE
U.S. model is shown.
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
\f—\f—
y

y
(\fy\f\fy
2008 TSX

The multi-inf ormation display in the
instrument panel displays various
inf ormation and messages when the
ignition switch is in the ON (II)
position. Some of the messages help
you operate your vehicle more
comf ortably.
Others help to keep you aware of the
periodic maintenance your vehicle
needs f or continued trouble-f ree
driving.When you turn the ignition switch to
the ACCESSORY (I) position, the
display shows ‘‘Goodbye.’’
There are three types of messages;
normal display messages, engine oil
lif e and maintenance messages, and
system messages.
You can also customize some vehicle
control settings to your liking with
the multi-inf ormation display and the
two buttons on the steering wheel
(see page ).
When you unlock and open the
driver’s door with the remote
transmitter, the display shows
‘‘Welcome Driver 1’’ or ‘‘Welcome
Driver 2’’ depending on which
remote transmitter you use. The
driver’s ‘‘ID’’ is detected by the
transmitter. For more information
about driver’s ‘‘ID’’, see page .If you use the key to unlock the
driver’s door, the display only shows
‘‘Welcome.’’ This means the system
cannot recognize either ‘‘Driver 1’’ or
‘‘Driver 2.’’ In this case, you cannot
use the customized settings on the
multi-inf ormation display (see page
).
86
13286
CONT INUED
Normal Display Messages
Multi-Inf ormation Display
Inst rument s and Cont rols
69
\f—\f—
y
y
(\fy\f\fy
2008 TSX

The multi-inf ormation display
consists of two segments; an upper
segment and a lower segment.
In normal display mode, the upper
segment displays trip computer. The
lower segment displays the
odometer, Trip A/B, outside
temperature, and engine oil lif e and
maintenance message.
Multi-Inf ormation Display
70
SECONDARY DISPLAYLOWER SEGMENT
PRIMARY DISPLAY
UPPER SEGMENT
: Press SEL/RESET Button.
: Press INFO Button.
U.S. model is shown
\f—\f—
y
\fy
(\fy\f\fy
2008 TSX

RANGE: The estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you received over the
last several miles, so it will vary
with changes in speed, traf f ic, etc.
ELAPSED TIME: The time
traveled since you last reset the
trip computer.
AVG. SPEED: The average speed
you are traveling.
TIRE PRESSURE MONITOR:
You can see the pressure of each
tire in this monitor. If the tire
pressure is low on one or more
tires, inf late them to the correct
pressure. For more inf ormation,
see page .
The primary display always shows its
def ault setting, ‘‘INST. MPG’’ (U.S.
models) or ‘‘INST. L/100 km’’
(Canadian models) even if you press
the INFO button. It only changes the
secondary display. You can
customize this setting to your liking
(see page ).
The upper segment is divided into
two displays; primary and secondary.
After you turn the ignition switch to
the ON (II) position, press the INFO
button on the steering wheel or the
INFO knob in the instrument panel.
What you last selected appears on
the secondary display of the trip
computer. Pressing the INFO
button/knob repeatedly changes the
display as shown in the example on
the previous page. Messages in the trip computer
include:
When you turn the ignition switch
to the ON (II) position, ELAPSED
TIME is reset.
INST.MPG(U.S.models)/
INST.L/100 km (Canadian
models): Your vehicle’s current
f uel mileage.
AVG. FUEL A/AVG. FUEL B:
Your vehicle’s average fuel
economy since you last reset the
Trip A or Trip B. When you select
Trip B in the lower segment by
pressing the SEL/RESET button
on the steering wheel or select/
reset knob in the instrument panel,
the AVG. FUEL B appears in the
secondary display. 102
264
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
71
INFO KNOBINFO BUTTON
——
y
y
(yy
2008 TSX

While a trip meter is displayed, you
can change the display between
‘‘Trip A’’ and ‘‘Trip B’’ by pressing
the SEL/RESET button on the
steering wheel, or the select/reset
knob in the instrument panel.
To reset a trip meter, display it, and
press and hold the SEL/RESET
button or select/reset knob until the
number resets to ‘‘0.0.’’ When you
reset ‘‘Trip B’’ , ‘‘AVG. FUEL B’’ is
also reset. If you reset ‘‘Trip A’’,
‘‘AVG. FUEL A’’ and ‘‘AVG. SPEED’’
willberesetatthesametime.
In the lower segment, each time you
press the SEL/RESET button on the
steering wheel, the display changes
f rom ‘‘Trip A/Odometer’’ to ‘‘Trip A/
Outside Temperature’’ to ‘‘Trip B/
Outside Temperature’’ to ‘‘Engine
OilLife,’’andthenbacktothe
‘‘Trip A/Odometer’’ as shown on
page . When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed. You can also change the display by
pushing the select/reset knob in the
instrument panel.
70
Multi-Inf ormation Display
Trip Meter
72
SELECT/RESET
KNOB
SEL/RESET
BUTTON
LOWER SEGMENT
U.S.model is shown
——
y

y
(yy
2008 TSX

This shows the outside Fahrenheit
temperature in U.S. models, and
Centigrade temperature in Canadian
models.The temperature sensor is in the
f ront bumper. The temperature
reading can be affected by heat
ref lection f rom the road surf ace,
engine heat, and the exhaust f rom
surrounding traf f ic. This can cause
an incorrect temperature reading
when your vehicle speed is under
19 mph (30 km/h). When you start
your trip, the sensor is not f ully
acclimatized, theref ore it may take
several minutes until the proper
temperature is displayed.
In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace.
You can adjust the outside
temperature display (see page ).
This shows the remaining lif e of the
engine oil. It shows 100% af ter the
engine oil is replaced and the display
is reset. The engine oil lif e is
calculated based on engine operating
conditions and accumulated engine
revolutions. For more inf ormation,
see page .
96
280
Multi-Inf ormation Display
Outside Temperature Engine Oil Lif e
Inst rument s and Cont rols
73
OUTSIDE TEMPERATURE
U.S.model is shown U.S.model is shownENGINE OIL LIFE
\f—\f—
y
y
(\fy\f\fy
2008 TSX

When the engine oil lif e reaches 15 %,
the display shows ‘‘SERVICE DUE
SOON’’ and the code f or the
maintenance items to be perf ormed.
When the engine oil lif e reaches 5 %,
the display shows ‘‘SERVICE DUE
NOW’’ along with the same
maintenance items.Have your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display af ter completing the service.
If you do not perf orm the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil lif e becomes 0 %.These messages appear on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position.
For more inf ormation about
Maintenance Messages, see
‘‘
’’ on page
.
Also ref er to page f or important
maintenance saf ety precautions. 280
278
Multi-Inf ormation Display
Maintenance Messages
Maintenance Minder
74
U.S.model is shown
\f—\f—
y
y
(\fy\f\fy
2008 TSX

CONT INUED
If there is a problem with your
vehicle, f or example, the engine oil
level is low or a door is not f ully
closed, the multi-inf ormation display
will show you the problem. It does
this by interrupting the current
display with one or more messages.The system message(s) triggers the
appropriate indicator(s) on the
instrument panel, including the
system message indicator, to come
on. The system message indicator
does not go of f until the problem(s)
is corrected.When there are several warnings to
be shown, the system switches the
messages every 5 seconds.
The message is shown until you
push the INFO button.
Toseethemessageagain,pressthe
INFO button, 5 seconds af ter the
display disappears.
Multi-Inf ormation Display
System Messages
Inst rument s and Cont rols
75
SYSTEM MESSAGE INDICATOR
\f—\f—
y

y
(\fy\f\f\fy
2008 TSX

Here is a table which shows the
possible multi-inf ormation display
messages and where to f ind f urther
inf ormation on each message.See page
78
See page 78
See page 78
See page 79
See page 79 See page
79
See page 80
See page 81
See page 81
See page
81
Multi-Inf ormation Display
76
\f—\f—
y
y
(\fy\f\f
y
2008 TSX

CONT INUED
See page82
See page 82
See page 83 See page
84
See page
82
See page 83 See page
84 See page
122
See page 85
See page
83
See page 84
Multi-Inf ormation Display
Inst rument s and Cont rols
77
\f—\f—
y

\fy
(\fy\f\fy
2008 TSX