change wheel Acura TSX 2008 Owner's Manual

RANGE: The estimated distance
you can travel on the fuel
remaining in the tank. This
distance is estimated from the fuel
economy you received over the
last several miles, so it will vary
with changes in speed, traf f ic, etc.
ELAPSED TIME: The time
traveled since you last reset the
trip computer.
AVG. SPEED: The average speed
you are traveling.
TIRE PRESSURE MONITOR:
You can see the pressure of each
tire in this monitor. If the tire
pressure is low on one or more
tires, inf late them to the correct
pressure. For more inf ormation,
see page .
The primary display always shows its
def ault setting, ‘‘INST. MPG’’ (U.S.
models) or ‘‘INST. L/100 km’’
(Canadian models) even if you press
the INFO button. It only changes the
secondary display. You can
customize this setting to your liking
(see page ).
The upper segment is divided into
two displays; primary and secondary.
After you turn the ignition switch to
the ON (II) position, press the INFO
button on the steering wheel or the
INFO knob in the instrument panel.
What you last selected appears on
the secondary display of the trip
computer. Pressing the INFO
button/knob repeatedly changes the
display as shown in the example on
the previous page. Messages in the trip computer
include:
When you turn the ignition switch
to the ON (II) position, ELAPSED
TIME is reset.
INST.MPG(U.S.models)/
INST.L/100 km (Canadian
models): Your vehicle’s current
f uel mileage.
AVG. FUEL A/AVG. FUEL B:
Your vehicle’s average fuel
economy since you last reset the
Trip A or Trip B. When you select
Trip B in the lower segment by
pressing the SEL/RESET button
on the steering wheel or select/
reset knob in the instrument panel,
the AVG. FUEL B appears in the
secondary display. 102
264
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
71
INFO KNOBINFO BUTTON
——
y
y
(yy
2008 TSX

While a trip meter is displayed, you
can change the display between
‘‘Trip A’’ and ‘‘Trip B’’ by pressing
the SEL/RESET button on the
steering wheel, or the select/reset
knob in the instrument panel.
To reset a trip meter, display it, and
press and hold the SEL/RESET
button or select/reset knob until the
number resets to ‘‘0.0.’’ When you
reset ‘‘Trip B’’ , ‘‘AVG. FUEL B’’ is
also reset. If you reset ‘‘Trip A’’,
‘‘AVG. FUEL A’’ and ‘‘AVG. SPEED’’
willberesetatthesametime.
In the lower segment, each time you
press the SEL/RESET button on the
steering wheel, the display changes
f rom ‘‘Trip A/Odometer’’ to ‘‘Trip A/
Outside Temperature’’ to ‘‘Trip B/
Outside Temperature’’ to ‘‘Engine
OilLife,’’andthenbacktothe
‘‘Trip A/Odometer’’ as shown on
page . When you turn the ignition switch to
the ON (II) position, what you last
selected is displayed. You can also change the display by
pushing the select/reset knob in the
instrument panel.
70
Multi-Inf ormation Display
Trip Meter
72
SELECT/RESET
KNOB
SEL/RESET
BUTTON
LOWER SEGMENT
U.S.model is shown
——
y

y
(yy
2008 TSX

If you want to set the customizable
vehicle control settings to the default
setting, press the INFO button on
the steering wheel until ‘‘DEFAULT
ALL’’ is displayed.
Press the SEL/RESET button to
enter ‘‘DEFAULT ALL.’’ You can
change the display between
‘‘CANCEL,’’ ‘‘OK’’ and ‘‘EXIT’’ each
time you press the INFO button.If you want to cancel ‘‘DEFAULT
ALL,’’ press the SEL/RESET button
while ‘‘CANCEL’’ is shown. The
display goes back to ‘‘CUSTOMIZE
ENTRY.’’
To set the def ault settings, press the
INFO button until the display
changesasshownabove.Pressthe
SEL/RESET button to select
‘‘DEFAULT ALL.’’
DEFAUL T AL L
Multi-Inf ormation Display
90
\f—\f—
y
y
(\fy\f\fy
2008 TSX

There are five custom settings in the
Meter Setup:LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.
DISPLAY
TRIP A & AVG. FUEL RESET
with REFUEL
ELAP. TIME RESET
CONDITION
PRIMARY DISP SELECTION
While ‘‘METER SETUP’’ is displayed,
press the SEL/RESET button on the
steering wheel. Then, press the
INFO button repeatedly. Each time
you press the INFO button, the
display changes as shown.
To customize a setting, press the
INFO button repeatedly until you see
the setting you want to customize,
and press the SEL/RESET button.
Then f ollow the procedures
described on the f ollowing pages.
CONT INUED
Meter Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
93
:Press the INFO Button.
\f—\f—
y
\f\fy
(\fy\f\fy
2008 TSX

While the multi-information display
is showing ‘‘METER SETUP,’’ press
the SEL/RESET button on the
steering wheel. The display changes
to ‘‘LANGUAGE SELECTION.’’
Press the SEL/RESET button again
to enter the language selection mode.There are three selectable languages,
English, French, and Spanish. Each
time you press the INFO button, the
display changes as shown.
Select the language you want by
pressing the INFO button, and press
the SEL/RESET button to enter
your selection.
L anguage Select ion
Multi-Inf ormation Display
94
: Press the INFO Button.
\f—\f—
y
\fy
(\fy\f\fy
2008 TSX

Press the SEL/RESET button. The
display changes as shown above.
The highlighted number is the
current adjustment above or below
the outside temperature. Press the
INFO button repeatedly until the
appropriate number appears, then
press the SEL/RESET button to
enter your selection.
If you f ind that the temperature
reading is always a f ew degrees
below or above the actual
temperature, adjust it as described
on the f ollowing columns.
While the multi-information display
shows ‘‘METER SETUP,’’ press the
SEL/RESET button on the steering
wheel. The display changes to the
‘‘CUSTOMIZE MENU.’’ Press the
INFO button once, and you will see
‘‘ADJUST OUTSIDE TEMP.
DISPLAY’’ as shown above.
A djust Outside T emp. Display
Multi-Inf ormation Display
96
U.S. model is shown
\f—\f—
y
y
(\fy\f
\f
y
2008 TSX

Press the SEL/RESET button. The
display changes as shown above.
The lower segment changes
between ‘‘ON’’ and ‘‘OFF’’ each time
you press the INFO button. Enter
your selection by pressing the SEL/
RESET button.
To set ‘‘Trip A’’ and ‘‘AVG. FUEL A’’
to reset every time you ref uel your
vehicle, f ollow the procedure
described f rom the next column.
While the multi-information display
shows ‘‘METER SETUP’’ press the
SEL/RESET button on the steering
wheel. The display changes to
‘‘CUSTOMIZE MENU.’’ Press the
INFO button repeatedly until you see
‘‘TRIP A & AVG. FUEL RESET
WITH REFUEL’’ in the lower
segment as shown above.
T rip A & A vg. Fuel Reset wit h Ref uel
Multi-Inf ormation Display
98
\f—\f—
y
y
(\fy\f
\fy
2008 TSX

‘‘ELAPSED TIME’’ is the driving
time since you last reset the trip
computer. You can customize the
condition of when to reset the
‘‘ELAPSED TIME’’.While the multi-information display
shows ‘‘METER SETUP,’’ press the
SEL/RESET button on the steering
wheel. The display changes to the
‘‘CUSTOMIZE MENU.’’ Press the
INFO button repeatedly until you see
‘‘ELAP. TIME RESET
CONDITION’’ in the lower segment
as shown above.Press the SEL/RESET button. The
display changes as shown above.
The lower segment changes
between ‘‘IGN RESET,’’ ‘‘TRIP A
RESET’’ and ‘‘TRIP B RESET’’ each
time you press the INFO button.
Enter your selection by pressing the
SEL/RESET button.
Elap. T ime Reset Condit ion
Multi-Inf ormation Display
100
\f—\f—
y
y
(\fy\f
\fy
2008 TSX

While the multi-information display
shows ‘‘METER SETUP,’’ press the
SEL/RESET button on the steering
wheel. Press the INFO button until
you see ‘‘PRIMARY DISP
SELECTION’’ as shown above.
When you turn the ignition switch to
the ON (II) position, the primary
display of the trip computer always
shows ‘‘INST. MPG’’ (U.S. models)
or ‘‘INST. L/100 km’’ (Canadian
models) in def ault setting. You can
customize this setting to your liking
in f ollowing procedure.
Press the SEL/RESET button. The
display changes as shown above.
The lower segment changes f rom
‘‘INST. FUEL,’’ to ‘‘AVG. FUEL,’’ to
‘‘RANGE,’’ to ‘‘ELAPSED TIME,’’
then to ‘‘AVG. SPEED’’ each time
you press the INFO button. Enter
your selection by pressing the SEL/
RESET button.
Primary Display Select ion
Multi-Inf ormation Display
102
\f—\f—
y
\f\f
\fy
(\fy\f
\fy
2008 TSX

While the multi-information display
shows ‘‘POSITION SETUP,’’ press
the SEL/RESET button on the
steering wheel. The display changes
to ‘‘MEMORY POSITION LINK’’ as
shown above.Press the SEL/RESET button. The
display changes as shown above.
Select ‘‘ON’’ or ‘‘OFF ’’ by pressing
the INFO button, and enter your
selection by pressing the SEL/
RESET button.
If ‘‘MEMORY POSITION LINK’’ is
‘‘ON,’’ the driver’s seat moves to the
positionstoredinthememorywhen
you open the driver’s door, using the
remote transmitter.
Refer to page for setting the seat
position memory. Also ref er to page
forremotetransmitteruse.
132 143
Position Setup
Memory Posit ion L ink
Multi-Inf ormation Display
104
\f—\f—
y
\f\fy
(\fy\f
\fy
2008 TSX