service reset Acura TSX 2008 Owner's Manual

When the engine oil lif e reaches 15 %,
the display shows ‘‘SERVICE DUE
SOON’’ and the code f or the
maintenance items to be perf ormed.
When the engine oil lif e reaches 5 %,
the display shows ‘‘SERVICE DUE
NOW’’ along with the same
maintenance items.Have your dealer do the indicated
maintenance as soon as you see this
message, and have them reset the
display af ter completing the service.
If you do not perf orm the indicated
maintenance or do not reset the
display, the message changes to
‘‘SERVICE PAST DUE’’ when the
engine oil lif e becomes 0 %.These messages appear on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position.
For more inf ormation about
Maintenance Messages, see
‘‘
’’ on page
.
Also ref er to page f or important
maintenance saf ety precautions. 280
278
Multi-Inf ormation Display
Maintenance Messages
Maintenance Minder
74
U.S.model is shown
\f—\f—
y
y
(\fy\f\fy
2008 TSX

µ
µ
µ
µ
µ
µ
µ
µ
µ
µµ
µ
To see the current engine oil lif e
displayed on the lower segment of
the multi-information display, turn
the ignition switch to the ON (II)
position, and press the SEL/RESET
buttononthesteeringwheel
repeatedly until engine oil lif e is
displayed. The remaining engine oil lif e is
shownonthedisplayaccordingto
this table:
Calculated Engine Oil Lif e (%)
100% 91% 90% 81%
80% 71%
70% 61%
60% 51%
50% 41%
40% 31%
30% 21%
20% 16%
15% 11%10% 6% 5% 1% 0% Displayed
Engine Oil Lif e (%)
100% 90%
80%
70%
60%
50%
40%
30%
20%
15%
10% 5%
0%
Your vehicle displays engine oil lif e
and maintenance service items on
the multi-information display to show
youwhenyoushouldhaveyour
dealer perf orm engine oil
replacement and indicated
maintenance service.
Based on the engine operating
conditions and accumulated engine
revolutions, the onboard computer in
your vehicle calculates the remaining
engine oil lif e and displays it as a
percentage.
Maintenance Minder
Engine Oil L if e Display
280
ENGINE OIL LIFE DISPLAY
REMAINING ENGINE OIL LIFE
\f—\f—
y
\fy
(\fy\fy
2008 TSX

To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
The message appears on the multi-
inf ormation display each time you
turn the ignition switch to the ON
(II) position. Af ter canceling the
message, the engine oil lif e display
will appear in the lower segment.
This continues until you have the
indicated maintenance done by your
dealer.When the remaining oil lif e is 5 to 1%,
the multi-information display shows
a ‘‘SERVICE DUE NOW’’ message.
The display also shows the same
maintenance items that were
previously shown with ‘‘SERVICE
DUE SOON.’’ Make sure you have
the indicated maintenance
perf ormed as soon as possible.To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
After have the service is performed,
make sure to reset the display as
described on page .
283
Maintenance Minder
282
\f—\f—
y


y
(\fy\fy
2008 TSX

If maintenance service is done by
someone other than your dealer,
reset the maintenance minder as
f ollows:Turn the ignition switch to the ON
(II) position.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display. Press and hold the SEL/RESET
button on the steering wheel f or
more than 10 seconds. The
remaining engine oil lif e reset
modewillbeshownonthemulti-
inf ormation display.
To reset the engine oil lif e, press
the INFO button on the steering
wheel to select ‘‘RESET’’ on the
display, and press the SEL/
RESET button.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage of the remaining engine
oil lif e and the maintenance item
code(s) displayed. Your dealer will reset the display
af ter completing the required
maintenance service. You will see
‘‘OIL LIFE 100 %’’ on the lower
segment of the multi-inf ormation
display and the maintenance item
code(s) erased the next time you
turn the ignition switch to the ON
(II) position.
If the engine oil lif e display is not
displayed, press the SEL/RESET
buttononthesteeringwheel
repeatedly until it comes back.
1.
2.
3.
CONT INUED
Maintenance Minder
Maint enance
283
‘‘SERVICE’’ MESSAGE
\f—\f—
y

y
(\fy\fy
2008 TSX

If you do not complete the reset
procedure within 30 seconds af ter
selecting the reset mode, the mode
will be canceled automatically.
If you have the required service
perf ormed but do not reset the
display, or reset the display without
perf orming the service, the system
will not show the proper
maintenance intervals. This can lead
to serious mechanical problems
because you will no longer have an
accurate record of when
maintenance is needed.To cancel resetting the oil life,
presstheINFObuttononthe
steering wheel to select
‘‘CANCEL’’ on the display, and
press the SEL/RESET button.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
If the indicated maintenance service
is not done and the remaining engine
oil lif e reaches 0 %, the multi-
inf ormation display will show the
message ‘‘SERVICE PAST DUE’’
and the maintenance item code(s).
This message is displayed when the
total mileage is less than 10 miles
(f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%. To cancel the message, press the
INFO button on the steering wheel.
Toseethemessageagain,waitfor
an interval for more than 5 seconds,
and then press the INFO button.
Maintenance Minder
284
\f—\f—
y

y
(\fy\fy
2008 TSX

CONT INUED
Also, the percentage ‘‘0 %’’ keeps
blinking on the display.
To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.If the indicated required service is
not done and the remaining engine
oil lif e becomes 0 %, the multi-
inf ormation display will show a
‘‘SERVICE PAST DUE’’ message,
thetotalmileageaftertheremaining
oillifebecame0%,andthe
maintenance item code(s).
This particular message is displayed
when the mileage is less than 10
miles (f or U.S. models) or 10 km (f or
Canadian models) af ter the engine
oillifebecame0%.
After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
percentage ‘‘0%’’ and the
maintenance item code(s) displayed.
Maintenance Minder
Maint enance
285
CANADA
U.S.
\f—\f—
y

y
(\fy\f\fy
2008 TSX

After the message on the multi-
inf ormation display is canceled by
pressing the INFO button, the
engine oil lif e display will appear in
the lower segment. You will see a
‘‘SERVICE’’ message along with the
maintenance item code(s), and the
total negative mileage af ter the oil
lif e becomes 0 % is displayed.
Immediately have the service
perf ormed, and make sure to reset
the display as previously described.
This message is displayed when you
drive over 10 miles (f or U.S. models)
or 10 km (f or Canadian models)
after seeing the 0 % message.
Also, the total negative mileage
keeps blinking on the display.
This particular message is displayed
when you drive over 10 miles (f or
U.S. models) or 10 km (f or Canadian
models) af ter seeing the 0 %
message.
To cancel the message, press the
INFO button on the steering wheel.
To see the message again, wait f or
an interval of more than 5 seconds,
and then press the INFO button. To cancel the engine oil lif e display,
press the SEL/RESET button to
return to the previous display.
Maintenance Minder
286
U.S.
CANADA
\f—\f—
y


y
(\fy\f
y
2008 TSX

Ì
If you have the required service
done but do not reset the display, or
reset the display without doing the
service, the system will not show the
proper maintenance intervals. This
canleadtoseriousmechanical
problems because you will no longer
have an accurate record of when
maintenance is needed. U.S. Vehicles:
According to state and federal
regulations, f ailure to perf orm
maintenance on the items marked
with will not void your emissions
warranties. However, all
maintenance services should be
perf ormed in accordance with the
intervals indicated by the
inf ormation display.
Your authorized dealer knows your
vehicle best and can provide
competent, ef f icient service.
However, service at a dealer is not
mandatory to keep your warranties
in effect. Maintenance may be done
by any qualif ied service f acility or
person who is skilled in this type of
automotive service. Keep all receipts
as proof of completion, and have the
person who does the work f ill out
your Maintenance Journal or
Canadian Maintenance Log. Check
your warranty booklet f or more
inf ormation.
We recommend the use of Acura
parts and f luids whenever you have
maintenance done. These are
manuf actured to the same high
quality standards as the original
components, so you can be conf ident
of their perf ormance and durability.
Maintenance Minder
Important Maintenance
Precautions
Maintenance, replacement, or
repair of emissions control
devices and systems may be done
by any automotive repair
establishment or individual using
parts that are ‘‘certif ied’’ to EPA
standards.
Maint enance
287
\f—\f—
y
\f\fy
(\fy\fy
2008 TSX

Î
Î
Ì Ì
Ì
Î
Maintenance Minder
289
:
If the message ‘‘SERVICE DUE NOW’’ does not appear more than 12 months
after the display is reset, change the engine oil every year.
Inspect idle speed every 160,000 miles (256,000 km).
Adjust the valves during services A, B, 1, 2, or 3 only if they are noisy. Independent of the maintenance messages in the multi-information
display, replace the brake fluid every 3 years.
See information on maintenance and emissions warranty, last column, page
.
NOTE: 1:
287
Maintenance Sub Items
Rotate tires
Replace air cleaner element If you drive in dusty conditions, replace every 15,000
miles (24,000 km).
Replace dust and pollen filter If you drive primarily in urban areas that have high
concentrations of soot in the air from industry and
from diesel-powered vehicles, replace every 15,000
miles (24,000 km).
Inspect drive belt
Replace transmission fluid Driving in mountainous areas at very low vehicle
speeds or trailer towing results in higher
transmission and transfer temperatures. This
requires transmission and transfer fluid changes
more frequently than recommended by the
maintenance minder. If you regularly drive your
vehicle under these conditions, have the transmission
and transfer fluid changed at 60,000 miles (100,000
km), then every 30,000 miles (48,000 km). (For A/T
only.)
Replace spark plugs
Inspect valve clearance
Replace engine coolant
Maintenance Main Items
Replace engine oil
Replace engine oil and oil filter
Inspect front and rear brakes
Check parking brake adjustment
Inspect these items: Tie rod ends, steering gearbox, and boots
Suspension components
Driveshaft boots
Brake hoses and line (including ABS)
All fluid levels and condition of fluids
Exhaust system
Fuel lines and connections
Symbol
Symbol
B A 1
2
3
4
51
1
Maintenance Minder
 — —
y

y
( y y
2008 TSX

CONT INUED
.......................................
Child Seats .36
......
LATCH Anchorage System .46
...........
Lower Anchorage Points .46
..........
Tether Anchorage Points .49
....................
Client Service Of f ice .366
..............
Climate Control Sensors .169
.........................
Clock, Setting the .204
...................................
Clutch Fluid .301
............
Cold Weather, Starting in .249
......................
Compact Spare Tire .324
.................
Console Compartment .157
.................
Consumer Inf ormation .366
.............
Controls, Instruments and .59
Coolant
........................................
Adding .295
....................................
Checking .236
.........................
Proper Solution .295
...................
Temperature Gauge .68
Crankcase Emissions Control ........................................
System .359
........
Cruise Control Message .85,206
............
Cruise Control Operation .206
....................
Cruise Main Indicator .66
...................................
Cup Holders .156
.......................
Customized Settings .86
....................................
Def ault All .90...............
Door · Window Setup .110
...........................
Lighting Setup .106
.................................
Meter Setup .93
...........................
Position Setup .104
........................
Setting to Def ault .90
...............................
Wiper Setup .117
...............
DANGER, Explanation of .iii
...................................
Dashboard .3,60
..............
Daytime Running Lights .122
........................................
Def ault All .90
............
Defects, Reporting Safety .368
..............
Def ogger, Rear Window .124
....................................
Dimensions .350
.............
Dimming the Headlights .121
Dipstick
.
Automatic Transmission .297,298
..................................
Engine Oil .236
........................
Directional Signals .121
........
Disc Brake Wear Indicators .260
.............
Display, Multi-inf ormation .69
.....................
Disposal of Used Oil .294
Doors ............
Locking and Unlocking .129 ..................
Lockout Prevention .130
...................
And Trunk Open .11,78
......................
Power Door Lock .129
.......................
Door Lock Mode .111
..........
DOT Tire Quality Grading .353
Downshif ting, 6-speed Manual
.............................
Transmission .250
...........
Driver and Passenger Safety .5
.......................................
Driver’s ID .86
...........................................
Driving .247
....................................
Economy .237
Driving Position ........................
Memory System .143
......
DRL, Check System Message .85
..........
Dual Temperature Control .167
..................
DustandPollenFilter .311
..............................
Economy, Fuel .237
....
Elapsed Time Reset Condition .100
Index
INDEX
DD
E
III
 — —
y
y
( y y
2008 TSX