Back up Acura TSX 2009 Owner's Manual

Make sure the engine and radiator
are cool.
Remove the radiator cap by
pushing down and turning
counterclockwise.
Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.
Put the radiator cap back on, and
tighten it fully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components. Check the f luid level in the
windshield washer reservoir at least
monthly during normal use.
Check the reservoir’s f luid level by
removing the cap and looking at the
level gauge attached to the cap.
4.
1.
2.
3. 5.
6.
Engine Coolant, Windshield Washers
Windshield Washers
424
RADIATOR CAP
LEVEL GAUGE
\f—\f—\fy
\fy
)!
\f\fy\fy
2009 TSX

Remove the dipstick (yellow loop)
f rom the transmission, and wipe it
with a clean cloth.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Remove the dipstick and check
the f luid level. It should be
between the upper and lower
marks.The transmission should be drained
andrefilledwithnewfluidwhenthis
service is shown on a maintenance
message in the multi-inf ormation
display.
If youarenotsurehowtoaddfluid,
contact your dealer.
If the level is below the lower
mark, add f luid into the dipstick
hole to bring it to the level
between the upper and lower
marks.
Pour the f luid slowly and caref ully
so you do not spill any. Clean up
any spill immediately; it could
damage components in the engine
compartment.
Always use Honda Genuine
ATF-Z1 (automatic transmission
f luid).
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Make sure the rubber cap on the
dipstick f its in the dipstick guide
and that you push the dipstick in
all the way.
2.
3. 5.
4. 6.
T ransmission Fluid
426
LOWER MARK
UPPER MARKGUIDE
Damage resulting f rom the use of
transmission f luid other than Honda
Genuine ATF-Z1 is not covered by the
Acura new vehicle warranty.
Using transmission f luid other than
Honda Genuine ATF-Z1 may cause
deterioration in transmission operation
and durability, and could result in
damage to the transmission.
Use only Honda Genuine ATF-Z1
(Automatic Transmission Fluid). Do
not mix with other transmission f luids.
\f—\f—\fy
y
)!
\f\fy\f
y
2009 TSX

CONT INUED
To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the cover on the back of
the headlight assembly by turning
the tab counterclockwise.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, and remove the
screw with a Phillips-head
screwdriver.
3.
4.
1.
2.
Canadian TSX
Lights
L ow Beam Headlight
Maint enance
431
TAB
COVER
SCREW HOLDING CLIP
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Open the hood.
To change the turn signal bulb on
the passenger’s side, remove the
engine coolant reserve tank by
pulling it out of its stay.
Insert the new bulb into the hole,
making sure the tabs are in their
slots.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Pivot the hold-down wire back in
place, and clip the end into the slot.
Reinstall the cover over the back
of the headlight assembly and turn
it clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back, then
remove the bulb.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way.
1.
8.
7.
9.
10.
11.
12.
5.
6.
Lights
High Beam Headlights
432
STAY
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the coolant reserve tank.
Reinstall the f asteners. Reinstall
the cover and upper part of the air
intake duct securely.
Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
To change a bulb on the lef t side,
remove the two f asteners by
turning the head of each f astener
with a flat-tip screwdriver, then
remove the cover and upper part
of the air intake duct.
2.
3. 4.
5.
6.
7.
On the passenger’s side
On the driver’s side
Lights
Maint enance
433
COVER
AIR INTAKE DUCT
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

Turn on the lights to make sure
the new bulb is working.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Install the new bulb and turn it
clockwise to lock it in place.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.
9.
7.
8.
6.
Lights
Maint enance
435
\f—\f—\fy

y
)!
\f\fy\f\fy
2009 TSX

CONT INUED
Open the trunk.
Toreplaceabulboneitherside,
remove the two f asteners on the
left side, or a fastener on the right
side.Pull back the appropriate corner of
the trunk lid lining caref ully.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
3. 4.
5.
1.
2.
Lights
Replacing a Back-up L ight Bulb
(in T runk L id)
Maint enance
437
FASTENERS SOCKET
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Reinstall the trunk lid lining. Make
sure it is installed under the edge
of the trunk seal.
Install the f asteners.Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
6.
7.
8.
9.
Lights
Side T urn Signal L ights
Rear License Plate Light Bulbs
438
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the holding clips, and
push in its head of each clip.
3.
4. 5.
6.
7.
8.
Lights
Maint enance
441
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

If you remove a f loor mat, make sure
tore-anchoritwhenyouputitback
in your vehicle.
If you use a non-Acura f loor mat,
make sure it f its properly and that it
canbeusedwiththefloormat
anchors. Do not put additional f loor
mats on top of the anchored mats.This f ilter removes the dust and
pollenthatisbroughtinfromthe
outside through the climate control
system.
Have your dealer replace the filter
when this service is indicated by a
maintenance message on the multi-
inf ormation display. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban
areas that have high concentrations
of soot in the air, or if the f low f rom
theclimatecontrolsystembecomes
less than usual.
Make sure the rear f loor mats are
properly positioned. If not, the f loor
mat will prevent the seat operation
and make the front passenger’s
weight sensors inef f ective. Dust and Pollen Filter Exterior Care
Floor Mats, Dust and Pollen Filter, Exterior Care
Maint enance
443
Chemical solvents and strong cleaners
can damage the paint, metal, and
plastic on your vehicle.
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX