Anc Acura TSX 2009 Owner's Manual

Canadian models only
If the washer f luid is low, a
‘‘WASHER FLUID LOW’’ message
appears on the multi-inf ormation
display.
Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.
When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition the blade edges.Check the f luid level with the engine
at normal operating temperature.
Park the vehicle on level ground.
Start the engine, let it run until the
radiator f an comes on, then shut
of f the engine. For accurate
results, wait about 60 seconds (but
no longer than 90 seconds) bef ore
doing step 2.
1.
CONT INUED
Automatic Transmission
Windshield Washers, T ransmission Fluid
Maint enance
425
DIPSTICK
Do not use engine antif reeze or a
vinegar/water solution in the
windshield washer reservoir. Antif reeze
can damage your vehicle’s paint, while
a vinegar/water solution can damage
the windshield washer pump. Use only
commercially-available windshield
washer f luid.
\f—\f—\fy

y
)!
\f\fy\f\fy
2009 TSX

Remove the dipstick (yellow loop)
f rom the transmission, and wipe it
with a clean cloth.
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Remove the dipstick and check
the f luid level. It should be
between the upper and lower
marks.The transmission should be drained
andrefilledwithnewfluidwhenthis
service is shown on a maintenance
message in the multi-inf ormation
display.
If youarenotsurehowtoaddfluid,
contact your dealer.
If the level is below the lower
mark, add f luid into the dipstick
hole to bring it to the level
between the upper and lower
marks.
Pour the f luid slowly and caref ully
so you do not spill any. Clean up
any spill immediately; it could
damage components in the engine
compartment.
Always use Honda Genuine
ATF-Z1 (automatic transmission
f luid).
Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Make sure the rubber cap on the
dipstick f its in the dipstick guide
and that you push the dipstick in
all the way.
2.
3. 5.
4. 6.
T ransmission Fluid
426
LOWER MARK
UPPER MARKGUIDE
Damage resulting f rom the use of
transmission f luid other than Honda
Genuine ATF-Z1 is not covered by the
Acura new vehicle warranty.
Using transmission f luid other than
Honda Genuine ATF-Z1 may cause
deterioration in transmission operation
and durability, and could result in
damage to the transmission.
Use only Honda Genuine ATF-Z1
(Automatic Transmission Fluid). Do
not mix with other transmission f luids.
\f—\f—\fy
y
)!
\f\fy\f
y
2009 TSX

If Honda MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
Remove the transmission f iller bolt,
and caref ully f eel inside the bolt hole
with your f inger.
The f luid level should be up to the
edge of the bolt hole. If it is not, add
Honda Manual Transmission Fluid
(MTF) until it starts to run out of the
hole. Reinstall the f iller bolt, and
tighten it securely.
Check the f luid level with the
transmission at normal operating
temperature and the vehicle sitting
on level ground.
The transmission should be drained
andrefilledwithnewfluidwhenthis
service is shown on a maintenance
message in the multi-inf ormation
display.
If you are not sure how to check and
add f luid, contact your dealer.
To check the transmission f luid level,
remove the bolts with a wrench, then
remove the under cover caref ully. Reinstall the under cover and tighten
theboltssecurely.Makesurethe
under cover is installed under the
edge of the f ront bumper.
T ransmission Fluid
Manual Transmission
Maint enance
427
Correct level
FILLER BOLT
BOLT UNDER COVER
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

Check the f luid level in the
reservoirs monthly. There are up to
two reservoirs, depending on the
model. They are:Always use Honda Heavy Duty
Brake Fluid DOT 3. If it is not
available, you should use only DOT 3
or DOT 4 f luid, f rom a sealed
container, as a temporary
replacement.
Using any non-Honda brake f luid can
cause corrosion and decrease the lif e
of the system. Have the brake
system f lushed and ref illed with
Honda Heavy Duty Brake Fluid
DOT 3 as soon as possible.
The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If the level is at or
below the MIN mark, your brake
system needs attention. Have the
brake system inspected f or leaks or
worn brake pads.
Brake f luid marked DOT 5 is not
compatible with your vehicle’s
braking system and can cause
extensive damage.
Brake f luid reservoir (all models)
Clutch f luid reservoir
(manual transmission models
only)
Replace the brake f luid when this
service is indicated on a maintenance
message in the multi-inf ormation
display.
You will also see the ‘‘BRAKE
FLUID LOW’’ message on the multi-
inf ormation display when the brake
f luid level is low. Brake Fluid
Brake and Clutch Fluid
428
MAX
MIN
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

The f luid level should be between
theMINandMAXmarksontheside
of the reservoir. If it is not, add
brake f luid to bring it up to that level.
Use the same fluid specified for the
brake system.A low f luid level can indicate a leak
in the clutch system. Have this
system inspected as soon as possible.
Manual Transmission only
Clutch Fluid
Brake and Clutch Fluid
Maint enance
429
MAX
MIN
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

CONT INUED
To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the cover on the back of
the headlight assembly by turning
the tab counterclockwise.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, and remove the
screw with a Phillips-head
screwdriver.
3.
4.
1.
2.
Canadian TSX
Lights
L ow Beam Headlight
Maint enance
431
TAB
COVER
SCREW HOLDING CLIP
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Install the new bulb, and turn it
one-quarter turn clockwise to lock
it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
Reinstall the coolant reserve tank.
Reinstall the f asteners. Reinstall
the cover and upper part of the air
intake duct securely.
Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
To change a bulb on the lef t side,
remove the two f asteners by
turning the head of each f astener
with a flat-tip screwdriver, then
remove the cover and upper part
of the air intake duct.
2.
3. 4.
5.
6.
7.
On the passenger’s side
On the driver’s side
Lights
Maint enance
433
COVER
AIR INTAKE DUCT
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

Turn on the lights to make sure
the new bulb is working.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Install the new bulb and turn it
clockwise to lock it in place.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.
9.
7.
8.
6.
Lights
Maint enance
435
\f—\f—\fy

y
)!
\f\fy\f\fy
2009 TSX

CONT INUED
Open the trunk.
Toreplaceabulboneitherside,
remove the two f asteners on the
left side, or a fastener on the right
side.Pull back the appropriate corner of
the trunk lid lining caref ully.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
3. 4.
5.
1.
2.
Lights
Replacing a Back-up L ight Bulb
(in T runk L id)
Maint enance
437
FASTENERS SOCKET
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the trunk, and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.Reinstall the socket. Turn it
clockwise until it locks. Make sure
the new bulb is working.
2.
1. 3.
Lights
Replacing the High-mount Brake
Light
Maint enance
439
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX