Engine Acura TSX 2010 Owners Manual

µµ
If the coolant level in the reserve
tank is at or below the MIN line, add
coolant to bring it up to the MAX line.
Inspect the cooling system f or leaks. If Honda antif reeze/coolant is not
available, you may use another
major-brand non-silicate coolant as a
temporaryreplacement.Makesureit
is a high-quality coolant
recommended f or aluminum engines.
Continued use of any non-Honda
coolant can result in corrosion,
causingthecoolingsystemto
malf unction or f ail. Have the cooling
system f lushed and ref illed with
Honda antif reeze/coolant as soon as
possible.
To access the radiator reserve tank,
remove the right-side engine
compartment cover.
Always use Honda Long-Lif e
Antif reeze/Coolant Type 2. This
coolant is pre-mixed with 50 %
antif reeze and 50 % water. Never add
straight antif reeze or plain water.
Except 6-cylinder models
A dding Engine Coolant
Engine Coolant
420
RESERVE TANK
4-cylinder models 6-cylinder models
If you regularly drive your vehicle
under severe conditions in very low
temperature (under 31°F, 35°C), a
higher concentration of coolant should
be used. Consult your Acura dealer f or
more inf ormation of the proper coolant.
2010 TSX

CONT INUED
Make sure the engine and radiator
are cool.Remove the radiator cap cover.
Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down.
If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
1.2.
3.6-cylinder models
Engine Coolant
Maint enance
421
RADIATOR CAP RADIATOR CAP COVER
4-cylinder models 6-cylinder models
Removing the radiator cap
while the engine is hot can
cause the coolant to spray out,
seriously scalding you.
Always let the engine and
radiator cool down before
removing the radiator cap.
2010 TSX

The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.
Put the radiator cap back on, and
tighten it fully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components. Check the f luid level in the
windshield washer reservoir at least
monthly during normal use.
Check the reservoir’s f luid level by
removing the cap and looking at the
level gauge attached to the cap.
Remove the radiator cap by
pushing down and turning
counterclockwise.
4. 5.
6.
7.
Engine Coolant, Windshield Washers
Windshield Washers
422
LEVEL GAUGE
RADIATOR
CAP
6-cylinder models 4-cylinder models
2010 TSX

Check the f luid level with the engine
at normal operating temperature.Park the vehicle on level ground.
Start the engine, let it run until the
radiator f an comes on, then shut
of f the engine. For accurate
results, wait about 60 seconds (but
no longer than 90 seconds) bef ore
doing step 2.
Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.
When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition the blade edges.
If the washer f luid is low, a
‘‘WASHER FLUID LOW’’ message
appears on the multi-inf ormation
display. 1.
CONT INUED
Canadian models only
Automatic Transmission
Windshield Washers, T ransmission Fluid
Maint enance
423
DIPSTICK
4-cylinder models
6-cylinder modelsDo not use engine antif reeze or a
vinegar/water solution in the
windshield washer reservoir. Antif reeze
can damage your vehicle’s paint, while
a vinegar/water solution can damage
the windshield washer pump. Use only
commercially-available windshield
washer f luid.
2010 TSX

If the level is below the lower
mark, add f luid into the dipstick
hole to bring it to the level
between the upper and lower
marks.
Pour the f luid slowly and caref ully
so you do not spill any. Clean up
any spill immediately; it could
damage components in the engine
compartment.
Always use Acura ATF-Z1
(automatic transmission f luid).Insert the dipstick all the way back
into the transmission securely as
shown in the illustration.
Make sure the rubber cap on the
dipstick f its in the dipstick guide
and that you push the dipstick in
all the way.
The transmission should be drained
and ref illed with new f luid when this
service is indicated by a maintenance
message on the multi-inf ormation
display.
If you are not sure how to add f luid,
contact your dealer.
5.
6.
4-cylinder models
T ransmission Fluid
Maint enance
425
Use only Acura ATF-Z1 (automatic
transmission f luid). Do not mix with
other transmission f luids.
Using transmission f luid other than
Acura ATF-Z1 may cause deterioration
in transmission operation and
durability, and could result in damage
to the transmission.
Damage resulting f rom the use of
transmission f luid other than Acura
AT F-Z1 is not covered by the Acura
new vehicle warranty.
2010 TSX

Remove the transmission f iller bolt,
and caref ully f eel inside the bolt hole
with your f inger.
Check the f luid level with the
transmission at normal operating
temperature and the vehicle sitting
on level ground.
The transmission should be drained
andrefilledwithnewfluidwhenthis
service is indicated by a maintenance
message on the multi-inf ormation
display.
If you are not sure how to check and
add f luid, contact your dealer.
To check the transmission f luid level,
remove the bolts with a wrench, then
remove the under cover caref ully. Reinstall the under cover and tighten
theboltssecurely.Makesurethe
under cover is installed under the
edge of the f ront bumper.
The f luid level should be up to the
edge of the bolt hole. If it is not, add
Acura Manual Transmission Fluid
(MTF) until it starts to run out of the
hole. Reinstall the f iller bolt, and
tighten it securely. If Acura MTF is not available, you
may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API
Certif ication seal that says ‘‘FOR
GASOLINE ENGINES’’ as a
temporary replacement. However,
motor oil does not contain the proper
additives, and continued use can
cause stiffer shifting. Replace as
soon as it is convenient.
Manual Transmission
T ransmission Fluid
426
Correct level
FILLER BOLT
BOLT UNDER COVER
2010 TSX

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustments
should be done by your dealer or
another qualif ied technician.The low beam headlight bulbs are
high voltage discharge tube bulbs.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
CONT INUED
High beam headlights on all models
Low beam headlights on Canadian TSXwith 4-cylinder engine
All models except Canadian TSX with
4-cylinder engine
Headlight Aiming L ow Beam Headlight Bulb
ReplacementReplacing a Headlight Bulb
Lights
Maint enance
429
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
2010 TSX

To change the passenger’s side
bulb, start the engine, turn the
steering wheel all the way to the
lef t, and turn of f the engine. To
change the driver’s side bulb, turn
the steering wheel to the right.Pull the inner f ender cover away
f rom the f ender and bumper.
Remove the cover on the back of
the headlight assembly by turning
the tab counterclockwise.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, and remove the
screw with a Phillips-head
screwdriver.
3.
4.
1.
2.
Canadian TSX with 4-cylinder engine
L ow Beam Headlight
Lights
430
TAB
COVER
SCREW HOLDING CLIP
2010 TSX

Open the hood.
Insert the new bulb into the hole,
making sure the tabs are in their
slots.
Push the electrical connector onto
the new bulb. Make sure it is
connected securely.
Pivot the hold-down wire back in
place, and clip the end into the slot.
Reinstall the cover over the back
of the headlight assembly and turn
it clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
Put the inner f ender cover in place.
Install the holding clip. Lock it in
placebypushingonthecenter.
Tighten the screw securely.
Remove the electrical connector
f rom the bulb by pulling the
connector straight back, then
remove the bulb. Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way.
Tochangeabulbonthe
passenger’s side, remove the
engine coolant reserve tank by
pulling it out of its stay. Remove all engine compartment
covers (see page ).
1.
8. 7.
9.
10.
11.
12.
5.
6.
2.
3.414
CONT INUED
6-cylinder models
High Beam Headlights
Lights
Maint enance
431
STAY
4-cylinder models
2010 TSX

Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
To remove the burned out bulb,
push it in and turn it
counterclockwise until it unlocks.
Use a f lat-tip screwdriver to
remove the holding clip f rom the
inner f ender, and remove the
screw with a Phillips-head
screwdriver.
Pull the inner f ender cover away
f rom the f ender and bumper.
To change the bulb on the driver’s
side, start the engine, turn the
steering wheel all the way to the
right, then turn of f the engine. To
change the bulb on the passenger’s
side, turn the steering wheel to the
lef t.
4.
5.
2.
1.
3.
Lights
Replacing a Front T urn Signal/
Parking and Side Marker Light
Bulb
434
SCREWHOLDING CLIP
2010 TSX