lights Acura TSX 2011 Owner's Guide

Towing a Trailer
Driving Safely with a Trailer
189
Continued
Driving
Things You Need To Know Before Towing a TrailerHave the trailer properly serviced and keep it in good condition. t
Make sure that all the weights and load in the vehicle and trailer are within t
limits.
Towing Load Limits

P.1 8 7
Securely attach the hitch, safety chains, and other necessary parts to the trailer. t
Securely store all the items in and on the trailer so that they do not shift while t
driving.
Check if the lights and brakes on the trailer are working properly. t
Check the pressures of the trailer tires, including the spare. t Towing Speeds and GearsDrive slower than normal. t
Obey posted speed limits for vehicles with trailers. t
Automatic transmission models
Use the tD
position when towing a trailer on level roads.
Turning and BrakingTurn more slowly and with a wider turning arc than normal. t
Allow more time and distance for braking. t
Do not brake or turn suddenly. t
Driving Safely with a Trailer
Driving Safely with a Trailer
Parking
In addition to the normal precautions, place wheel
chocks at each of the trailer's tires.

191
Continued
Driving
When DrivingStarting the Engine
1. Make sure the parking brake is applied.
Starting the Engine
Keep your foot firmly on the brake pedal when
starting the engine.
The engine is harder to start in cold weather and
in thinner air found at altitudes above 8,000 feet
(2,400 meters).
When starting the engine in cold weather, turn off
all electrical accessories such as the lights, climate
control system, and rear defogger in order to reduce
battery drain.
If exhaust sounds abnormal or you can smell
exhaust gas inside the vehicle, have your vehicle
checked by a dealer. There may be a problem with
the engine or exhaust system.
Automatic transmission models 2. Check that the shift lever is in P
, then
depress the brake pedal.
Although it is possible to start the
vehicle in N
, it is safer to start it in P
.
Manual transmission models 2. Check that the shift lever is in N
. Then
depress the brake pedal with your right
foot, and the clutch pedal with your left
foot.
The clutch pedal must be fully depressed
to start the engine.
Brake Pedal
Brake Pedal Clutch Pedal

Before Performing Maintenance
222Maintenance
Inspection and MaintenanceFor your safety, perform all listed inspections and maintenance to keep your
vehicle in good condition. If you become aware of any abnormality (noise, smell,
insufficient brake fluid, oil residue on the ground, etc.), have your vehicle inspected
by a dealer. (Note, however, that service at a dealer is not mandatory to keep
your warranties in effect.) Refer to the separate maintenance booklet for detailed
maintenance and inspection information.
Types of Inspection and Maintenance Daily inspections
Perform inspections before long distance trips, when washing the vehicle, or when
refueling. Periodic inspections
Check the automatic transmission fluid level monthly. t
Automatic Transmission Fluid

P. 2 4 2
Check the brake fluid level monthly. t
Brake/Clutch Fluid

P. 2 4 4
Check the tire pressure monthly. Examine the tread for wear and foreign t
objects.
Checking and Maintaining Tires

P. 2 5 9
Check the operation of the exterior lights monthly. t
Replacing Light Bulbs

P. 2 4 7
Check the condition of the wiper blades at least every six months. t
Checking and Maintaining Wiper Blades

P. 2 5 7
Inspection and Maintenance U.S. models Maintenance, replacement, or repair of
emissions control devices and systems may be
done by any automotive repair establishment
or individuals using parts that are "certified"
to EPA standards.

According to state and federal regulations, failure
to perform maintenance on the maintenance main
items marked with # will not void your emissions
warranties. However, all maintenance services
should be performed in accordance with the
intervals indicated by the multi-information display.
Maintenance Service Items


P. 2 2 7
If you want to perform complex maintenance tasks
that require more skills and tools, purchase the
service manual.
Authorized Manual


P. 3 13

If you want to perform maintenance yourself, make
sure that you have the necessary tools and skills
first.
After performing maintenance, update the records
in the separate maintenance booklet.

Replacing Light Bulbs
Headlight Bulbs
248Maintenance
Headlight Bulbs
The exterior lights' inside lenses (headlights, brake
lamps, etc.) may fog temporarily after a vehicle
wash or while driving in the rain. This does not
impact the exterior light function.
However, if you see a large amount of water or ice
accumulated inside the lenses, have your vehicle
inspected by a dealer.
Driver side
4-cylinder models 3. Remove the fasteners, using a flat-tip
screwdriver. Remove the cover of the air
intake duct and its upper part. 6-cylinder models 3. Remove the fasteners, and remove the air
intake duct cover.
Fastener
Fastener
Air Intake
Duct Cover
Cover
6-cylinder models 4-cylinder models

Replacing Light Bulbs
Headlight Bulbs
250Maintenance
Low Beam Headlights
1. Turn the steering wheel all the way to the
opposite side from the headlight being
replaced.
Passenger side: Turn the steering wheel
to the left.
Driver side: Turn the steering wheel to
the right.
2. Remove the holding clips and screws, and
pull the inner fender back.
3. Rotate the cover to the left, and remove.
Low Beam Headlights
High voltage can remain in the circuit for a long period of time after the light is
switched off. Do not attempt to inspect or replace the high voltage discharge type
bulbs yourself. Ask a dealer to inspect and replace low beam headlights.
Low Beam Headlights
When removing the clip, insert a flat-tip screwdriver,
and lift and remove the central pin.
High Voltage Discharge Type Halogen Type
Inner Fender
Screw
Cover Clip

Replacing Light Bulbs
Fog Light Bulbs
251
Continued
Maintenance
4. Unhook the hook, and pull out the
connector.
5. Remove the old bulb and insert the new
bulb.
6. Put the connector back into the headlight
assembly.
Low Beam Headlights
When mounting the clip, insert while keeping the
central pin of the clip raised, and push until the pin
is flat.
Push until the
pin is flat
Fog Light BulbsWhen replacing, use the following bulbs.
Fog Lights: 55W
1. Remove the clip using a flat-tip screwdriver,
and lower the under cover.
Fog Light Bulbs NOTICE Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass can cause the
bulb to overheat and shatter.
The fog lights are halogen bulbs.
When replacing a bulb, handle it by its plastic case,
and protect the glass from contact with your skin
or hard objects. If you touch the glass, clean it with
denatured alcohol and a clean cloth. Hook
Connector Bulb
Clip
Under Cover

Replacing Light Bulbs
Front Turn Signal/Parking/Side Marker Light Bulbs
252Maintenance
Front Turn Signal/Parking/Side Marker Light BulbsWhen replacing, use the following bulbs.
Front Turn Signal/Parking/Side Marker: 21/5WTurn the steering wheel and pull the inner fender back in the same way as when
replacing the low beam headlights.
Changing the Low Beam Headlight

P. 2 5 0
1. Turn the socket to the left and remove it.
2. Push in the old bulb, rotate to the left until
it unlocks, and remove.
3. Insert a new bulb.2. Remove the coupler.
It can be removed by pushing the tab.
3. Rotate the old bulb to the left to remove.
4. Insert new bulb.
BulbSocket
Bulb
Ta b
Coupler

Replacing Light Bulbs
Side Turn Signal/Emergency Indicator Light Bulbs
253
Continued
Maintenance
Brake Light, Taillight, Rear Turn Signal Light and
Rear Side Marker Light BulbsWhen replacing, use the following bulbs.
Brake/Taillight: 21/5W
Rear Turn Signal Light: 21W
Rear Side Marker Light: 3CP
1. Pull out and remove the cover.
Side Turn Signal/Emergency Indicator Light BulbsDoor mirrors have the side turn lights. Have an authorized Acura dealer inspect
and replace the light bulbs.
Cover

277
If a Tire Goes Flat
Continued
Handling the Unexpected
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually
to reduce speed. Then, stop in a safe place. Replace the flat tire with the compact
spare tire. Go to a dealer as soon as possible to have the full size tire repaired or
replaced.
1. Park the vehicle on firm, level, and non-slippery ground. Automatic transmission models 2. Put the shift lever in P
.
Manual transmission models 2. Put the shift lever in R
.
All models 3. Set the parking brake.
4. Turn on the hazard warning lights and turn the ignition switch to LOCK 0
.
Changing a Flat Tire
Periodically check the tire pressure of the compact
spare. It should be set to the specified pressure.
Specified Pressure: 60 psi (420 kPa, 4.2 kgf/cm
2)
When driving with the compact spare tire, keep
the vehicle speed under 50 mph (80 km/h). Replace
with a full size tire as soon as possible.
The compact spare tire and wheel in your vehicle
are specifically for this model.
Do not use them with another vehicle.
Do not use another type of compact spare tire or
wheel with your vehicle.
Do not mount tire chains on a compact spare tire.
If a chain-mounted front tire goes flat, remove one
of the full-size rear tires and replace it with the
compact spare tire. Remove the flat front tire and
replace it will the full size tire that was removed
from the rear. Mount the tire chains on the front
tire.
Do not use a puncture-repairing agent on a flat tire,
as it can damage the tire pressure sensor.
Changing a Flat Tire

283
Engine Does Not Start
Handling the Unexpected
Checking the EngineIf the engine does not start, turn the ignition switch to START III
and check the
starter.
Checking the Engine
If you must start the vehicle immediately, use an
assisting vehicle to jump start it.
Jump Starting


P. 2 8 4

Starter condition Checklist
Starter doesn't turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.Check brightness of the interior light.
Turn on interior lights and check brightness.
If the interior lights are dim or do not come on at all t
 Battery Inspection and Maintenance P. 2 6 8
If the interior lights come on normally t
Fuse Inspection and Replacement
P. 2 9 4
The starter turns over normally
but the engine doesn't start.
There may be a problem with the
fuse. Check each of the items on
the right and respond accordingly.Review the engine start procedure.
Follow its instructions, and try to start the engine again.
Starting the Engine P.1 9 1
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
 Immobilizer System P. 9 8
Check the fuel level.
There should be enough fuel in the tank.
Fuel Gauge P. 7 5
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
 Inspecting and Changing Fuses P. 2 9 7
If the problem continues:
 Emergency Towing P. 2 9 8