light Acura TSX 2011 Workshop Manual

Braking
210Driving
Brake System
Parking Brake
Use the parking brake to keep the vehicle stationary when parking.
To a p p l y :
Pull the lever fully up without pressing the
release button.
To r e l e a s e :
1. Pull the lever slightly, and press and hold
the release button.
2. Lower the lever down all the way, then
release the button.
Parking Brake NOTICE Release the parking brake fully before driving. The
rear brakes and axle can be damaged if you drive
with the parking brake applied.If you start driving without fully releasing the
parking brake, a buzzer sounds as a warning, and
"RELEASE PARKING BRAKE" appears on the multi-
information display.
Always apply the parking brake when parking.
To prevent the parking brake from freezing when
the outside temperature is extremely cold, do not
apply it, but do the following: Automatic transmission models Put the shift lever in
P, then use a block or other
wheel chock to stop the wheels from turning.
Manual transmission models Put the shift lever in
R or
1, then use a block or
other wheel chock to stop the wheels from turning.

Braking
Brake System
211
Driving
Foot Brake
Your vehicle is equipped with disc brakes at all four wheels. A power assist helps
reduce the effort needed on the brake pedal. The brake assist system increases the
stopping force when you depress the brake pedal hard in an emergency situation.
The anti-lock brake system (ABS) helps you retain steering control when braking
very hard.
Brake Assist System

P. 2 13
ABS (Anti-lock Brake System)


P. 2 12
Foot Brake
Check the brakes after driving through deep water,
or if there is a buildup of road surface water. If
necessary, dry the brakes by lightly depressing the
pedal several times.
If you hear a continuous metallic friction sound
when applying the brakes, the brake pads need to
be replaced. Have the vehicle checked by a dealer.
Constantly using the brake pedal while going down
a long hill builds up heat, which reduces the brake
effectiveness. Apply engine braking by taking your
foot off the accelerator pedal and downshifting to
a lower gear. With manual transmission use a lower
gear for greater engine braking.
Do not rest your foot on the brake pedal while
driving, as it will lightly apply the brakes and cause
them to lose effectiveness over time and reduce pad
life. It will also confuse drivers behind you.

Braking
ABS (Anti-lock Brake System)
212Driving
ABS (Anti-lock Brake System)
ABS
Helps prevent the wheels from locking up, and helps you retain steering control by
pumping the brakes rapidly, much faster than you.
The electronic brake distribution (EBD) system, which is part of the ABS, also
balances the front-to-rear braking distribution according to vehicle loading.
You should never pump the brake pedal. Let the ABS work for you by always
keeping firm, steady pressure on the brake pedal. This is sometimes referred to as
"stomp and steer."
ABS (Anti-lock Brake System) NOTICE The ABS may not function correctly if you use an
incorrect tire type and size.
When the ABS indicator comes on while driving,
there may be a problem with the system.
While normal braking is not affected, there is a
possibility of the ABS not operating. Have the
vehicle checked by a dealer immediately.
The ABS does not reduce the time or distance it
takes to stop the vehicle. It only helps with steering
control during hard braking.
In the following cases, your vehicle may need more
stopping distance than a vehicle without ABS:
When driving on rough road surfaces, including twhen driving on uneven surfaces, such as gravel
or snow.
When tire chains are installed. tYou may hear a motor sound coming from the
engine compartment while system checks are being
performed immediately after starting the engine or
while driving. This is normal.
ABS operation
The brake pedal may pulsate slightly when the ABS is working. Keep holding the
pedal firmly down. On dry pavement, you will need to press on the brake pedal
very hard before the ABS activates. However, you may feel the ABS activate
immediately if you are trying to stop on snow or ice.
When the vehicle speed goes under 6 mph (10 km/h), the ABS stops.

Braking
Brake Assist System
213
Driving
Brake Assist System
Brake Assist System
Designed to assist the driver by generating greater braking force when you depress
the brake pedal hard during emergency braking.
Brake assist system operation
Press the brake pedal firmly for more powerful braking.
When brake assist operates, the pedal may wiggle slightly and an operating noise
may be heard. This is normal. Keep holding the brake pedal firmly down.

Maintenance
This chapter discusses basic maintenance.
Before Performing Maintenance
Inspection and Maintenance .............. 222
Safety When Performing
Maintenance .................................... 223
Parts and Fluids Used in
Maintenance Service ........................ 224
Maintenance Minder
™ ........................ 225
Maintenance Under the Hood
Maintenance Items Under the Hood .. 229
Opening the Hood ............................. 231
Recommended Engine Oil .................. 234
Oil Check ........................................... 235
Adding Engine Oil .............................. 237Engine Coolant .................................. 240
Transmission Fluid .............................. 242
Brake/Clutch Fluid .............................. 244
Refilling Window Washer Fluid ........... 246
Replacing Light Bulbs ......................... 247
Checking and Maintaining Wiper
Blades ................................................ 257
Checking and Maintaining Tires
Checking Tires ................................... 259
Tire and Loading Information Label .... 260
Tire Labeling ...................................... 260
DOT Tire Quality Grading
(U.S. Vehicles)
.................................... 262Wear Indicators .................................. 264
Tire Service Life .................................. 264
Tire and Wheel Replacement ............. 265
Tire Rotation ...................................... 266
Winter Tires ....................................... 267
Battery ................................................. 268
Remote Transmitter Care ................... 269
Replacing the Battery ........................ 269
Climate Control System
Maintenance ..................................... 270
Cleaning
Interior Care ........................................271
Exterior Care ...................................... 273
221

Before Performing Maintenance
222Maintenance
Inspection and MaintenanceFor your safety, perform all listed inspections and maintenance to keep your
vehicle in good condition. If you become aware of any abnormality (noise, smell,
insufficient brake fluid, oil residue on the ground, etc.), have your vehicle inspected
by a dealer. (Note, however, that service at a dealer is not mandatory to keep
your warranties in effect.) Refer to the separate maintenance booklet for detailed
maintenance and inspection information.
Types of Inspection and Maintenance Daily inspections
Perform inspections before long distance trips, when washing the vehicle, or when
refueling. Periodic inspections
Check the automatic transmission fluid level monthly. t
Automatic Transmission Fluid

P. 2 4 2
Check the brake fluid level monthly. t
Brake/Clutch Fluid

P. 2 4 4
Check the tire pressure monthly. Examine the tread for wear and foreign t
objects.
Checking and Maintaining Tires

P. 2 5 9
Check the operation of the exterior lights monthly. t
Replacing Light Bulbs

P. 2 4 7
Check the condition of the wiper blades at least every six months. t
Checking and Maintaining Wiper Blades

P. 2 5 7
Inspection and Maintenance U.S. models Maintenance, replacement, or repair of
emissions control devices and systems may be
done by any automotive repair establishment
or individuals using parts that are "certified"
to EPA standards.

According to state and federal regulations, failure
to perform maintenance on the maintenance main
items marked with # will not void your emissions
warranties. However, all maintenance services
should be performed in accordance with the
intervals indicated by the multi-information display.
Maintenance Service Items


P. 2 2 7
If you want to perform complex maintenance tasks
that require more skills and tools, purchase the
service manual.
Authorized Manual


P. 3 13

If you want to perform maintenance yourself, make
sure that you have the necessary tools and skills
first.
After performing maintenance, update the records
in the separate maintenance booklet.

229
Maintenance Under the Hood
Maintenance
Maintenance Items Under the Hood 4-cylinder models
Brake Fluid
(Black Cap)
Engine Oil Dipstick
(Orange Handle)
Washer Fluid
(Blue Cap)
Engine Coolant
Reservoir
Radiator Cap
Manual transmission models Clutch Fluid
(Light Gray Cap)
Engine Oil Fill Cap Automatic transmission models Automatic Transmission Fluid
Dipstick (Yellow Loop)

Maintenance Under the Hood
Opening the Hood
231
Continued
Maintenance
Opening the Hood
1. Park the vehicle on a level surface, and set
the parking brake.
2. Pull the hood release handle under the
lower left corner of the dashboard.

The hood will pop up slightly.
3. Push up the hood latch lever in the center
of the hood to release the lock mechanism,
and open the hood.
4-cylinder models 4. Remove the support rod from the clamp
using the grip. Mount the support rod in
the hood.
When closing, remove the support rod, and
stow it in the clamp, then gently lower the
hood. Remove your hand at a height of
approximately 12 inches (30 cm) and let the
hood close.
Opening the Hood NOTICE Do not open the hood when the wiper arms are
raised.
The hood will strike the wipers, and may damage
either the hood or the wipers.
When closing the hood, check that the hood is
securely latched.
If the hood latch lever moves stiffly, or if you can
open the hood without lifting the lever, the latch
mechanism should be cleaned and lubricated.
Grip
ClipSupport Rod
Hood Release Handle
Pull
Lever

247
Replacing Light Bulbs
Continued
Maintenance
When replacing, use the following bulbs.
High beam headlight: 60W (HB3)
Low beam headlight: 55W (H1 for halogen bulb Type)
35W (D2S for high voltage discharge type)
High Beam Headlight
6-cylinder models 1. Remove all the engine compartment
covers.
Engine Compartment Covers

P. 2 3 3
Passenger side
All models 2. Remove the engine coolant reservoir.
Headlight Bulbs NOTICE Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the glass can cause
the bulb to overheat and shatter.
The headlight aim is set by the factory, and typically
does not need to be adjusted. However, if you
regularly carry heavy items in the trunk or tow a
trailer, have the aiming readjusted at a dealer or by
a qualified technician.
The HB3 and H1 types are halogen bulbs.
When replacing a bulb, handle it by its base, and
protect the glass from contact with your skin or
hard objects. If you touch the glass, clean it with
denatured alcohol and a clean cloth.
Headlight Bulbs
Engine Coolant
ReservoirEngine Coolant
Reservoir
6-cylinder models 4-cylinder models

Replacing Light Bulbs
Headlight Bulbs
248Maintenance
Headlight Bulbs
The exterior lights' inside lenses (headlights, brake
lamps, etc.) may fog temporarily after a vehicle
wash or while driving in the rain. This does not
impact the exterior light function.
However, if you see a large amount of water or ice
accumulated inside the lenses, have your vehicle
inspected by a dealer.
Driver side
4-cylinder models 3. Remove the fasteners, using a flat-tip
screwdriver. Remove the cover of the air
intake duct and its upper part. 6-cylinder models 3. Remove the fasteners, and remove the air
intake duct cover.
Fastener
Fastener
Air Intake
Duct Cover
Cover
6-cylinder models 4-cylinder models